Super Beast Module 12volt Conversion

[@michaelcharge4783]

Best 12v super beast headway conversion I have seen so far!

[@MrM_Full-Send]

Thank you 😊

[@drfoulcheese]

Thank you for the video. The way you showed to convert it is much easier than others have shown.

[@craftchest]

Very nice. Thanks!

[@danvird8649]

does this turn the bank into 96ah?

[@MrM_Full-Send]

correct

[@SamuelHollandsh]

Thank you

[@MrM_Full-Send]

You are welcome!!

[@myrontaylor77]

Do you need a BMS. Or should you use a BMS?

[@MrM_Full-Send]

yes bms is recommended. the next video i did was hooking up a 4s battery management system to a modified beast module

[@curtisnavarro7098]

Is that a Robot Underground sub?

[@MrM_Full-Send]

No sir. That is a Rebuilt JVF custom. It is an RE destroy motor on a Cerwin Vega Stroker ST154D ti style basket with an Sundown Audio X15 megaroll v2 surround

[@drfoulcheese]

If you could possibly tell me what balancer I would need I would really appreciate it or post an Amazon link. I had a 5 wire balancer.

[@drfoulcheese]

It should be just an 8s balancing board right?

[@MrM_Full-Send]

5A 3S 4S 12V Battery Active Equalizer a.co/d/4URYtIF

[@MrM_Full-Send]

@@drfoulcheese 4s this is the one I used

[@drfoulcheese]

In the video you said it would need 8 wires. I must be confused lol

[@MrM_Full-Send]

@@drfoulcheese correct. Plates 2,3&4 need to be split because those plates aren’t connected. There are two of each of those plates and each needs a wire. So… depending on balancer… yellow green and white need to be conned to two plates

[@guerrillawar616]

What’s your amp hour to wattage?

[@MrM_Full-Send]

These units are 1.23 kWh

[@ATCA]

Yea. Ill just redo half thr bank and reduce the need for this x shape connections

[@MrM_Full-Send]

Normally I just pull cells and put them onto buss bars but.. this is an example of an alternative approach that may work for some people 🤷‍♂️

[@ATCA]

@@MrM_Full-Send I've built my sets of buss bars. Sometimes I just want to keep it like it is

[@MrM_Full-Send]

Flipping 24 cells seems like a lot more work to achieve the same outcome. However, as is often the case, there is more than one right way to do things 😊

[@jimn8389]

I bought 2 of these and fully charged them to 14.6 volts also and I did not disassemble them I made them into two 12.8 Volt per super beast which should be a total of 192 amp hours at 12.8 volts to my surprise my inverter shut off at 10 volts and when I recharged both superbeasts all together only took 50 amp hours so something is not right with these batteries. 50 amp hours is not even close to 192 amp hours. Anyone else testing these?

[@MrM_Full-Send]

🤔.all the ones that i have purchased have worked out pretty good. that being said… i have had a few cells crap out on me. i guess that is a risk when buying used cells. but two entire banks seems a bit much🤔. did you reach out to battery hook up?

[@jimn8389]

@@MrM_Full-Send just finished charging them an hour ago and will call battery hookup tomorrow

[@luisvillalobos4976]

There’s another Chanel that explains this way better.

[@MrM_Full-Send]

cool!