Very nice product. Good design and a valuable addition to the machine. VERY WELL DONE.
@Grizz0220 Жыл бұрын
Can’t wait for mine to arrive!
@ddlanguages6497 Жыл бұрын
idea is good .. but as you pushing and pulling that guide back and forth ...i can see it wobbling ...may need to tweek the design a bit
@themotofixery3 жыл бұрын
Can this be set up to traverse across the belt rather than along the belt? This would be useful for grinding something wider than two inches.
@griftopherhitchens9926 Жыл бұрын
Any way I can get some general dimensions to rig it to my BEE grinder?
@BeaumontMetalWorks Жыл бұрын
The surface grinder attachment connect to the 1.5 inch square tool arm of the KMG and KMG-TX 2x72 belt grinders. The support plate for the unit attaches to the bottom of the tool arm, while the contact wheel spindle is on the top of the same tool arm. The tri-helix contact wheel is 3 inches wide (and 2.5 in diameter) with its edge starting a half inch away from the tool arm. Hopefully that helps!
@superazzoto84333 жыл бұрын
Salve ,mi puoi dire di cosa è composto il davanti , sono calamite o altro e a cosa servono ( tenere il pezzo per la lavorazione forse ?) Grazie se mi vorrai rispondere
@BeaumontMetalWorks3 жыл бұрын
83 / 5000 Translation results Il mandrino è in acciaio al carbonio con magneti al neodimio scanalati che trattengono le parti ferrose.
@doc5593 жыл бұрын
🏆🏆🏆👍🙏 Thank you for sharing ❄️⛄🎅🎄
@dr.jecklemisshigh94293 жыл бұрын
How is this to use this with a non horizontal grinder?
@BeaumontMetalWorks3 жыл бұрын
It is designed to work with belt grinders in either vertical or horizontal mode. For vertical operation, such as on a classic KMG, rotate the base plate so that the magnetic chuck arm can move freely across the surface of the abrasive wheel. Chose and angle that is comfortable for use and also allows the chuck sufficient clearance past the wheel. This video shows one vertical setup. There are some other vertical setups shows on Beaumont's instagram posts @BeaumontMetalWorks and on our website BeaumontMetalWorks.com
@rudyjackson22533 жыл бұрын
Will this work on the classic
@BeaumontMetalWorks3 жыл бұрын
Yes, this surface grinder attachment works very well on the classic KMG. It is designed for use on either the classic KMG or the KMG-TX.
@castelmichel86703 жыл бұрын
Nice piece, very useful in a metal shop for quick dimensioning. On a side note Please wear a mask or a respirator. I cringed watching you breathe all that silica and metal dust dust. Nice work.
@BeaumontMetalWorks3 жыл бұрын
Good tip! Definitely good advice!
@jacquelinesears17709 ай бұрын
You got to be kidding me My mom fell for this sh!t when i was a kid you want to buy a Vacuum Cleaner
@jacquelinesears17709 ай бұрын
It does it all
@koolsolutionszx12r553 жыл бұрын
As a machinist with a critical eye for precision parts. THIS HAS FAR TOO MUCH SLOP IN ITS MOVEMENT. Just watch it flopping about even on light cuts. It's a good start but it needs at least two additional rollers on the back side of that slide to stop it from flopping about in it's track. That and nect time have the man that built it demo it not the CEO whom is cllearly not very mechanically inclined
@peterstenabaugh30413 жыл бұрын
@Johnny One Plate I am also a machinist and this thing makes me cringe. Why not have a small aluminum bar - screwed down to the magnetic plate instead of pounding in some roll pins. Aluminum bar with 2 brass screws. The other thing he doesn't address is how to clean off the grinding dust. These guys needs to design a mag chuck that can be turned off, it's not rocket science. It's waaaaaay too expensive for what you get.
@OUTDOORS552 жыл бұрын
These type of belt surface grinders are not for ultra precision work. They are for FAST work such as grinding knife flats and flattening. Knives do not require Precision down to .0001 its a complete wast of time and you would never make any money. Theres a tool for every job.
@jacknissen60402 ай бұрын
taper grind procedure is flawed. grind one side then the blade will need to be shimmed with a tapered shim