Suzuki Intruder VS1400: Remove Cylinder Head Case - Tear Down Part 15

In this video, I will show you how to remove the head cases/units from the engine of a 1997, Suzuki Intruder vs1400/Boulevard. I have the task of changing the piston rings to look forward to and this is the first step of getting to them. By removing the cylinder head on this motorcycle, I will be able to access the valves and valve springs of the Suzuki VS1400 intruder as well. This means that I can inspect, and fix any issues that I may currently be having with the cam and cam chain on the bike.
Hagar Moto Website: For detailed, step-by-step instructions, visit:
bit.ly/3bdUWEp
Suzuki Intruder Workshop Manual:
Clymer Repair Manual Suzuki Intruder VS1400: amzn.to/3onx9FP
Popular Clutch Parts for Suzuki Intruder VS1400:
Full Clutch Kit by Barnett: amzn.to/3hMq1k1
Clutch Gasket by Caltric: amzn.to/3rUlrEZ
Clutch Friction Plates by Caltric: amzn.to/2Lrtsk0
Gasket and Friction Plate Kit by Caltric: amzn.to/2XeMvQW
Tapered Steering Stem Bearings by All Balls: amzn.to/38jGlWc
Popular Carburetor Parts for Suzuki Intruder VS1400:
Carburetor Rebuild Kit by KIPA: amzn.to/35bGWY7
Rear Diaphram Membrance by Lanbao: amzn.to/2MIDrCd
Popular Fuel System Parts for Suzuki Intruder VS1400:
Spark Plugs by NGK: amzn.to/38hsZtB
Iridium Spark Plug by NGK: amzn.to/2JQ3o1n
Pod Filters by DNA: amzn.to/3s1AA7u
Fuel Pump by Bruce & Shark: amzn.to/35dxG5S
Fuel Pump by OSIAS: amzn.to/2LrUc3T
Popular Brakes Parts FOR Suzuki Intruder:
Front and Rear Brake Pads by Master Chen: amzn.to/2JQlgJD
Popular Electrical System Parts for Suzuki Intruder VS1400:
Replacement Battery (YTX16-BS-1) by PowerStar: amzn.to/2XjjXWy
Popular Tools:
22 Litre Ultrasonic Cleaner: amzn.to/397dDXN
6.5 Litre Ultrasonic Cleaner: amzn.to/2MGCFpd
BelRay High-Quality Waterproof Grease: amzn.to/2LaLerV
Rotary Tool: amzn.to/2MGU9lh
Screw Driver Set: amzn.to/392Fato
If you have any questions, please leave them in the comment section below, hit subscribe and I'll get back to you asap.
_____________
This is the biggest project I have taken on, The bike will be completely stripped down to the frame, the engine will be removed for new piston rings to be installed, the wiring harness is going to be rewired and the entire bike overhauled, ready for spring 2020....I hope.
[***Disclaimer***]
Please keep in mind that I am not a mechanic, I have no professional training and the advice that may be interpreted from these videos is purely my own opinion and does not reflect that of which a professional mechanic or motorcycle engineer would provide.
-------
Motorcycle Specs:
Manufacturer: Suzuki
Model: Intruder VS1400
Year: 1997
Engine Size: 1360cc
Fuel Type: Petrol - Four Stroke
Cooling System: Air/Oil Cooled
Transmission: 5 Speed
-------
Camera Gear:
Sony A7iii
Interfit SuperLite 9
Neewer LED 660 Panel
Sennheiser MKE300 External Mic
#hagarmoto #suzukivs1400 #suzukiintruder

Q&A -> Thanks for checking out the video, if you have any questions drop them here!

[@ryanridesmoore]

Loving your videos man. Saved me a few times so far.

Glad to know they are helping you Ryan :)

[@tttony9426]

hay bubs,ive just bought a 99 / 1400,its in mint condition But its popping pretty bad at idle and acceleration,its coming from the back cylinder only,the previous owner replaced the stock pipes with 6 inch shortys,im hoping by putting the stock pipes back it will help with this problem,,if its a burnt valve,is that maybe fixable by spraying some cleaner into the carb throat while its running OR what do you think,,thanx for your shows i really enjoy learning more about the intruder,in my opinion they are the best looking and riding bikes out there, ill take my early model broncos and my intruder anyday over anything else,

[@MrLinkinho]

Do you think a head gasket replacement would be possible without removing the engine on a c50?

[@MadiliaSarwary]

Did you find out the reason oil leaking in to the air cleaner?

[@RogerWilco66]

Oh man. I took off the bolts of the rear cylinder head on the right side (the long ones). The rear bolt went off fine, but the front one snapped way down where it is threaded into the engine case. I guess I have a ruined block now?!

[@jimmibak9616]

Hi. I have a wierd ticking noise from from front cylinder. I fear its my headgasket. Do I need to remove the intire engine from the bike to change it or can it be done on the bike?

Hi Jimmy, a ticking noise would usually signify metal on metal. If you find me on Facebook and send me a video ill try to point you in the right direction

[@jimmibak9616]

@ i will make a video tomorrow and send you. Thanks 😃

[@jimmibak9616]

I was a little delayed but I send you a dm on Facebook Hägar.

[@ЖораКаспаров-у5ж]

Молодец 💪👍

[@danielrivera1663]

I need to change the top gasket on a same motorcycle. I see that the frame is in the way of taking the long screws out. Do i need to take off the entire motor and transmission out the frame or how can i get it do? Please help!

You need to remove the engine to remove the cylinder bolts my friend. You might be able to manoeuvre the front bolts around the frame but it would likely be more trouble than it is worth. There is an engine removal video on the channel as well which might help. Best of luck!

[@danielrivera1663]

Thanks for the info. Will let you know the outcome.

[@coltonspellman7170]

I need help I need to know where all the head bolts go buddy took it apart an now we don't now where what ones go where

Have you got a copy of the green workshop manual?

[@Frenchy1312]

What's the right setting for valves?

Setting? These ones are not adjustable.my friend, whats important is the position of the cams when putting the head back together. I go through that in my top end rebuild video

[@patriciochipantashi1327]

Necesito poner el punto de encendido de la c50 suzuki año 2005 un video de esa por favor

[@rumppan]