Suzuki Quadrunner 250 Carb Rebuild!!!

[@Raffuentes030999]

Great video! Do you have part 2. Also the throttle screw to the carburetor what is the bottom setting to start on? Thx

[@undeserved1781]

mechanic extraordinaire

[@lucasramsburg7629]

Ngl I was lost doing this, but you saved my ass man. Thanks a lot. Very helpful video

[@twintwo1429]

Despite the new comers, like I was, in the beginning, this is all basic mechanical crap. You learn and you get way better, real quick. MEN, PLEASE LEARN THIS AND PASS IT ON TO EVERYONE. NO ONE LOSES WHEN WE LEARN AND PASS IT ON EVERY DAY. LADIES, DO THE SAME, PLEASE.

[@chrismaciejewski2568]

Yeah you my kinda people . Facts

[@johnzygmunt6073]

10:39 good video I just bought a 1991 250 4wd and someone deleted the fuel pump and switched the lines around on the carb any idea where I can get a vent , vacuum and fuel diagram? Thanks

[@adamyz8198]

I took the air box out on mine and had a lot more room to work in but the boots were the worst to put back on.

[@HoursFreeAOLsp]

I am working on a King quad 300 and I just did an engine swap from a donor quad, Jesus Christ though I cannot get the carb back in. Like you said the rubber boots fuck you in the ass with no lube.

[@ferguson20diesel49]

Found it easy enough. Got be patient lads.

[@dw4940]

1000HoursFreeAOL sp totally eh

[@dw4940]

Ferguson 20 diesel how’s it easy? Maybe easy compared to a really hard job lol. Or the rubber boots are loose goose like a hookers snatch!

[@TheFritz423]

I used words I haven't used in a long time. Total PITA.

[@lavender_heart5263]

4:38 does that go on the small elbow peice down there?

[@zaksnook3200]

I have the same model bike same size engine I picked it up for a deal everything runs fine he clean the carb before he sold it to me just wondering on where the idle screw was people are saying it’s on the right side near the back or on top I can’t find it for the life of me

[@dickwelts8817]

I took mine apart and almost had the brass cable end adapter @14:20 for the throttle cable roll down into the intake manifold. So I swept the ground for a 10 foot radius around the Quad and found it, lucky I did

[@Loompius]

Jesus

[@elliot7179]

This is a bastard of a job especially the bloody choke cable , ive since put two inline filters on mine so i hopefully never have to do this crap again haha

[@ferguson20diesel49]

Elliot everyone is saying the choke cable was a pain. I thought it was easiest simple job job ever

[@jeffreyferlotte6379]

I was doing a polaris trailboss that had a similar carb, couldnt get a wrench on it. Ended up taking the whole lever and cable out of handle bar hole, cleaned it while still attached, runs mint

[@MerchantMetals]

leaving fuel on can dump gas into your crank case? i left mine on for a month sitting there. brushed snow off and it stared real hard then started idling high thinking it was just the cold making it act up. i ride off into the woods for it to die on me. then i noticed a nasty smell from exhaust. so i think no oil? i unscrew the rear oil cap and watch gas and oil (mainly gas) rush out like it was in a hurry or something. is my bike screwed? where do i start to fix this? there is no vent line port on this fuel petcock just 1 gas line from the petcock to carburetor. think if i just change the oil and make sure the gas is shut off after each use will fix this? or do i need to be looking elsewhere for problems.

[@RogueMachines17]

most likely you can drain everything out, put in new oil and at least see if any damage was done. You probably did not do any damage but you won't really know until you tear it apart or try running it. If the fuel is left on it can fill the bowl and leak into the combustion chamber and then into the oil. Root cause issue could be a bad or leaking float valve. Correct fix is to replace the float valve, but even new ones can leak. turning off the fuel can prevent this issue entirely

[@MerchantMetals]

@RogueMachines17 thank you friend this was helpful. I've never seen so much fuel come out of a crankcase.

[@macharrington7853]

Any one tell me where the line that come direct off the petcock that gives fuel where to hook it up? I got the vacuum line on top twords engine and the caged line on the bottom by the float and itll run but die after a few moments of running

[@alexanderramosn1428]

I just bought one and the owner said it sat for a year of no use, ive put gas into it and it just cranks over like it wants to start but wont. I suspect its not getting gas but i dont know where to start?

[@brodenmurray4047]

Thanks mate this came in very handy, your a champ😊

[@quintonbraylen8530]

i guess I'm kind of off topic but do anybody know of a good website to stream new movies online?

[@graysonelliott5649]

@Quinton Braylen I dunno I watch on Flixportal. you can find it on google :) -grayson

[@quintonbraylen8530]

@Grayson Elliott Thanks, I went there and it seems like a nice service :D Appreciate it!!

[@graysonelliott5649]

@Quinton Braylen happy to help =)

[@Loompius]

Basically standing on those bowls screws hahah it's always like that

[@Crazybrother802]

I have 87 Quad Runner that gas goes into the oil . Wood rebuilding carburetor fix this problem?

[@RogueMachines17]

Do you shut your fuel off when it sits?

[@Crazybrother802]

@@RogueMachines17 i just changed the oil so I will try shutting the off the gas when it’s setting. Thank you

[@MerchantMetals]

@@Crazybrother802 did this work for you or did it fill back up with gass?? im in the same boat. my crank case is full of gas and i left my fuel on.

[@chrismaciejewski2568]

It's a good video, dude and thank you.I watch a lot of these videos on pretty much.Anything that I do like this because I really don't know And I just want to say it's probably better if you just go to the video afterwards and talk and explain what you're doing instead of the music. Cause yeah, if you know what you're doing on this kind of stuff.It's helpful for us But I find a lot of The Times the music is just a kind of annoying. just trying to get you some More views so theres more people out here that know what they are doing cause yeah it's a good video thanks

[@jerryf581]

How did you get that dang plastic nut restarted? Not enough room to use a wrench.....HELP!!!!!!!!!!!

[@RogueMachines17]

There are many different nuts to loosen and tighten in the process... at what time in the video is the same nut you were talking about removed?

[@jerryf581]

The plastic choke plunger nut. Removal from 7:06 thru 12:35. I just can't seem to get it restarted..

[@jerryf581]

Nevermind, I got it.....finally. Thanks, anyway!

[@TheFritz423]

I ground down a cheap 12 mm wrench to fit

[@xandscrazyworks2561]

Hey sir I have that same quad. Would You mind making a video of how the vacuum lines are ran. I've been trying to find a diagram and I couldnt find anything. I switched to a low pressure electric fuel pump which was a very bad idea because of not knowing how to route the vacuum lines.

[@RogueMachines17]

Zhavonnetie Alexander sorry, I really would but i sold that quad a few months back

[@1208ink]

Zhavonnetie Alexander did you ever find what you needed ? If not I'll be rebuilding a carb tomorrow I'll get you some pics it's easier than explaining it

[@colingeorge2431]

I replied to a comment up above explaining the carb and vacuum a bit. I wouldn't change it they need to creat vacuum to work. To open the safty pit cock. The vacuum from carb opens it and allows the gas to go to fuel pump which also works on a vacuum. The one single line on top front of carb is vaccum for pit cock. Check for cracks or lose connections. The other to lines and back upper part of carb is vaccum as well think for fuel pump will reply again when finshed quad I am working.

[@Jacoblikestoskim]

What size wrench did u use for the choke

[@Loompius]

12 mm

[@undeserved1781]

like those tools and the selection of them u must work in cycle shop

[@Brian-my3gd]

because he has screw drivers and combination wrenches? doesn't get much more basic than that.

[@awptickes]

What's the music used in this video?

[@snkombo2586]

hi, do you have any idea why my suzuki goes so bad, it revs up and sometimes you can't even drive because its like its getting to mock fuel or to less? it dies and goes really bad, have cleaned the carb, bhougt a new choke cable, whats the problem? it is getting maybe air somewhere?

[@RogueMachines17]

It could be your valves. Suzuki quadrunner exhaust valves are know to leak. I would check your compression

[@colingeorge2431]

They work of vacuum. Your carb works up the vacuum in the top part with the big rubber diaphragm. It then opens the safty pit cock that works with having to have vacuum. Then letting gas get pumped to fuel pump then on to carb. If your bike has not been used in years I would go ebay and order new pit cock and fuel pump and replace it . Also any lines that are dryed up in the vacuum lines..you can try that first before replacing the pit and pump. This works as I have fixed these in the past and have one in my garage know with same issues..found broken pit cock line that could cause the issues and the diaphragm in carb looks worn. Good starting point for lot of Suzuki that have all these vacuums lines on them

[@snkombo2586]

the bikes works now(: it drives good

[@dickwelts8817]

@@colingeorge2431 That's is almost the same system as a Yamaha Vino scooter I just fixed, no fuel was getting through the pit cock and fuel pump. it had a vacuum tube from the carburetor, so I bought a new fuel pump and it started right up . I am buying a new fuel pump for my 96 Suzuki Quarunner 250, I cleaned the carb already, so I'll have to check the fuel pump

[@1stclassgarage771]

can anyone tell me what the fuel petcock vavle looks like on a 1999 suzuki king quad 300

[@snkombo2586]

the thing that you removing in around 7:38 is that the choke? because then i need a new cable hehe

[@RogueMachines17]

sn kombo yes, hope it all goes well for you

[@snkombo2586]

RogueMachines17 oh okey thanks, where can i found the cable? I cant find the cable that looks exactly like this, i have the golden thing in the carburator but not the rest of it

[@RogueMachines17]

I have copied two links to what I think you need (only the cable) - www.partsgiant.com/p341663-motion-pro-choke-cable?m=538990&gclid=CjwKCAiA3JrQBRBtEiwAN7cEGtBbq8SqOL5DwXuMptj6i1l4sy5VvDk5Ole6s98v4IdL6ZpG7OVkaxoCNM0QAvD_BwE&f=114712 www.summitracing.com/parts/mnp-04-0112/applications/model/lt-4wd-quadrunner-250 If you need the new parts inside the carb (spring, plunger, or cap) will be the part numbers 16, 45, 44, 43 on this website - USE THE LINKED WEBSITE FOR THESE PARTS www.suzukipartshouse.com/oemparts/a/suz/50d0b118f870022c2c53634f/carburetor-model-l-m-n-p-r-s

[@snkombo2586]

RogueMachines17 yrs thank you, i need the 45,44,43 to get the cable to fit in there,

[@snkombo2586]

do you now if they deliver to sweden?

[@beautyflower5452]

How do you take off the seat

[@RogueMachines17]

Beauty Flower there is a latch on the left side of the seat (as if sitting on it) pull either towards front or back of the atv and push the seat forwards then lift up on the seat

[@wadewarnock5926]

Do you happen to know where I can get an aftermarket carburetor for this model 4wheeler

[@RogueMachines17]

My best bet would be ebay. If not, try rebuilding the current carb and increasing the jets slightly.

[@rickybobbyinc293]

Don’t buy a cheap $75 knock-off you have to buy a used or real Mikuni carb, but it will run $300+. Or buy the China-junk and keep rebuilding it every month.

[@rickybobbyinc293]

Bike Life_93 : That can be true if you are lucky and get a good one. The parts just aren’t made that great, that’s why they are so cheap. With name brand, its one and done. But hey, my advice ain’t for everyone. Have at it and be safe!

[@Badhacktime]

The cheap Chinese carb also burn spark plug preferably rebuild yours or buy a OEM one so you won't burn you spark plug in one week it maybe more expensive to get the OEM but you get your money back when you think of how many spark plug you've burned in a month

[@elainebaker2573]

where is the other part of this video

[@RogueMachines17]

Elaine Baker there is no other part. that is the complete disassembly and just do the opposite for reassembly

[@undeserved1781]

did you fumble with everything on reassembly like the ignorant disassembly easy to see you are lost

[@rickybobbyinc293]

There is sooooo much more if you want to even moderately rebuild that carb. SMH!

[@TheFritz423]

@@undeserved1781 Lighten up, Francis

[@alexanderraykhert1019]

I thought you sold the quad runner 250?

[@RogueMachines17]

AlexMoto I did, this is footage I filmed a month before I sold it and never uploaded

[@mrdodgeman9566]

Mine won’t idle

[@mrdodgeman9566]

I’m just tryna find the idle screw damit

[@thcnred1]

Large Philips coming out of the bottom of carb

[@39knights]

I have one of these bikes (1992 250 2x4). Anyone else out there want to take the sob so-called engineers that needlessly designed these serviceable parts into such tight spaces out behind a woodshed for a much needed a**-whooping. I found the choke plunger near impossible to put back on and with a wrench ???? forget it. Choke plunger is a 12mm wrench but needle nosed pliers worked far better.

[@jerryf581]

Heck yeah, they need a serious beat down!!LOL!! Man, how did you get that dang thing started??

[@JoseSanchez-dv5sw]

ok

[@curtischislett3215]

I need your help ASAP please I have the same bike please message me back

[@RogueMachines17]

I sold this atv about 4 years ago but I'd be more than glad to help you as much as I can

[@helenegirard6959]

Sorry,pry off

[@rubenbenitez785]

The music is terrible 😂😂