Swept Blend in-depth | Ramsbottom safety valve in Creo Parametric

[@vikassinha9557]

This part consumes lot of time because of tiny features thanks sir learn something new today

[@arabstar50]

Dear Mr Satinder Your tutorials are great ❤️

[@ravichandrauppin4418]

Thank you very much sir for sharing your immense knowledge with everyone one....

[@franciscomorales3396]

Muchas gracias por enseñarnos a conocer este software.

[@kelvinle8662]

Right click and hold for half a second for the dropdown menu to appear.

[@uday29]

small doubt sir how you take 50 degrees for axis at 22:20 for rib and also radius 3 at end of video

[@CADxTraining]

I have considered it 50 degrees as it gives me the best result. Actually it should be tangent there. But I was getting some error when I was using tangent condition there. So I considered 50 degrees to get the result.

[@arkaaldov5893]

Thank you! You are the best!

[@arkaaldov5893]

Do you have any future plans on covering assemblies and multibody parts? Also a quick tip explaining hole options in parts? Such as linear and diameter etc... Thank you for all the hard work please keep it up!

[@CADxTraining]

Yes, it's coming soon.

[@swapnil8854]

Thanks sir nice explanation

[@chetanargiddi3352]

Sir do u hve practise exercise from start to end which cover all function one by one

[@wildtiger.]

Sir, How you mentioned the centre line for rib sketch Please explain!

[@CADxTraining]

I have taken it as approx value

[@omkargarud84]

Sir you have added the part drawing next to the model tree. Can you guide me how to do that ?

[@piyushrampariya4652]

Overall fantastic . super..but where is the dimensions in the sketch page. Show as during sketching .

[@CADxTraining]

I didn't understand your question.

[@piyushrampariya4652]

Sir ..you make sketch from a 2d drawings..where all dimensions are given..but you take dimensions very fast from that drawings . Our mind don't get it.

[@CADxTraining]

You can pause the video sometime in between to understand the topic better. I don't indicate dimensions all the time to reduce the length of the video. That is why I keep the drawing open all the time on the screen. Hope you can understand the reason.

[@piyushrampariya4652]

Ok sir ji ...your all videos are great upper thanks a lot.

[@antonysilverious5626]

sir can u please try swept blend method ..i tried swept blend to create the part but i cant able to create the rib feature

[@CADxTraining]

If you are following swept blend method then at the rib using extrude.

[@antonysilverious5626]

@@CADxTraining got it sir ..I used The extrude feature now .. it worked ..but can I know the reason sir why rib feature is not working in swept blend method

[@CADxTraining]

The surface generated by swept blend is different than extrude and revolve.

[@antonysilverious5626]

@@CADxTraining yes sir while doing swept blend .. the surface was not fully closed to do rib feature ... So like u said I did extrude instead of rib ... Thank u for helping me out sir .. learning a lot from u daily

[@CADxTraining]

Keep learning

[@prasadhire184]

Sir in my creo 7 when i use "Skecher pallets" then i received "fatal error -traceback error" Get only when sketcher pallets i use

[@CADxTraining]

There is some technical issue. Uninstall creo and try to reinstall.

[@prasadhire184]

@@CADxTraining it occurs every time i reinstall so many times

[@CADxTraining]

You try any other version to check

[@prasadhire184]

@@CADxTraining i checked 5 6 7 8 version

[@CADxTraining]

Than this will be the graphics related issue

[@yuvaraj8556]

sir how to add pcd as shown in this drawing

[@CADxTraining]

There is no direct method in Creo parametric to do this. You can only do this by adding a draft entity.

[@sandeeppk3564]

Super sir... Thank you...

[@chetanargiddi3352]

Start point and blend vertex not coming while right click

[@CADxTraining]

Just right click will not work. Right click and hold the right click, you will get the options.

[@agsamuel10]

How to keep the drawing on the left as you did in creo?

[@CADxTraining]

This is done by video editor

[@agsamuel10]

@@CADxTraining Thank you so much sir, Your videos are so helpful.

[@gasserjoshua7448]

22:19 how did you derive 50 degrees? Love your videos!

[@CADxTraining]

I have considered it 50 degrees as it gives me the best result. Actually it should be tangent there. But I was getting some error when I was using tangent condition there. So I considered 50 degrees to get the result.

[@gasserjoshua7448]

@@CADxTraining understood thank you for the explanation

[@niharika9524]

Thanks sir

[@chetanargiddi3352]

During video all time dimension sketch is showing which cover half area of display that is annyoing