SolidWorks Tutorial

[@capitaocavernadobras]

Parabéns. Ótimo Trabalho. Obrigado por compartilhar.

[@carlosmaffessoni4638]

So ingenious and useful video, a truly revision of basic SW resources. Although it has no sound is perfectly easy to follow, thank you!

[@khalidashzz]

in 11:10 he chose the line to the left downward (the one with the gab of 5mm with respect to the line he draws) and the point of contact between the two lines and then chose (make coincident ) check the selected entities box in his selection to ensure that you choose the right one!

[@Peace10427]

Hey man, at 6:00 min you made a hard cut and the lower two circles sit no more on the 12.7 mmm offset.... where did you chance a measure that they mve into the offset?

[@SamnissArandeen]

This is quite awesome. I should ask, though...where are the rest of the mains? What about oil galleries? The water jacket is nice, but there's no ports for water to be pumped in and out.

[@simatmakina2963]

thankyou: ) very Much. Bror. God bless you..

[@kakanipavan801]

Can please please tell which car engine model is these

[@joseluisMartin]

really nice job, you've got the dimensions of the model?

[@sairocadiz9571]

how did you make the line in 11:10?? thanks

[@ManojKumar-lv5qo]

Very nice. If you explain evey command in English it becomes more useful.

[@kinhvule6470]

at 11:09 i don't understand how can you do that? i can't do it in my drawing, please help me!!

[@dragoro3033]

Hopefully you found the solution, but if not and you are still interested -> My solution was going back to the very first part and drawing out the shape of the engine. My numbers were wrong. check those, and make sure they match up. that fixed it for me.

[@Eviscerate86]

Hey. You are my SW mentor. After car engine project is done what would be your next project? I am hoping for a jet engine. Thanks always!!

[@Sw-tcNet]

Lust Thanks Lust for your comment. Yes, you are right. a jet engine is planned a little later. after covering a motor cycle and it's engine!

[@2slamsala7]

how can i get full dimensions of all parts of engine ?

[@bravelionfamous2552]

Hello, would you like please to tell me how would I be able to see clearly the demensions of different pieces in those tutorials? should I subcribe or so? I hope to get the answer very soon, because IM in dire need to learb more about solidworks, thanks in advance

[@muhammedince4429]

ı can't select the centerline in the move/copy command.( 10:00 ) How did selected the line ?

[@Lalogalviz]

gracias amigo por estos tutoriales son muy buenos exitos

[@ZZ-ob4pc]

I am truly enjoying working on the engine with you. I just want to know why are the holes in the block not aligned? and why you never used the "hole wizard" for the holes?

[@TitovIgorBro]

Hey everyone: this video is outdated a little and now it's better to copy&rotate using the circular pattern function

[@danielhamonangan799]

my thin feature is checked when I want to make the boss-extrude and it can not be unchecked, please help!!!!

[@sumitpatil6346]

why didn''t you use mirror command for left and right side block

[@christianjimenez1169]

Very niiiiiiiice. How do you do the thing at the end with all the purple lines??

[@timmyp1337]

Hey at 14:14 do you filet all the inside corners or just the three you did?

[@mahirkepic3273]

Did you find out the answer?

[@stonelisek2787]

any issues building this in solid works 2012. looking to start this tomorrow on my 2012 software.

[@jerryiceland]

Hello Bro. Thanks for this project. I have a little problem completing the engine block. Did you combine both bodies to make it one solid block. The combine function is not working for me. Pls help. Thanks

[@Sw-tcNet]

Jerry Iceland Thanks bro for comment. No I didn't use the combine because it will combine automatically after extruding the shorter body!

[@jerryiceland]

SolidWorks Tutorial ☺ ok thanks very much for your reply . I'll try it again

[@ilyasata1723]

Tiresome but, it is good exercise.

[@kakanipavan801]

Can please please tell which car engine model is these

[@dariodedomenico5647]

At 6:38 I can’t understand how you make that rib

[@adeelsyed7291]

What command did you use at 3:53 to give all the snap points of the circle?

[@3goldy]

Where is the feture of "Always Assume Symmetry", so it can save the indevidual use of "mirror" for EVERY SINGLE feture?

[@Sw-tcNet]

3goldy is there an icon for it? the second half of block is not symmetric.

[@3goldy]

SolidWorks Tutorial ☺ this software should have it.

[@AhmedSaberSayed]

how did you fix the cut at 5:48 ??

[@AhmedSaberSayed]

the origin suddenly is no longer mid point and I don't understand why

[@danielbustos7801]

what you have to do is take the first sketch and make the constructive line, the middle point of the top line.

[@AhmedSaberSayed]

Thanks man, but I already figured it out but I have a note to tell you. the cam shaft mechanical rotation isn't reasonable. Isn't there a way to make the gear mesh with the cam shaft to make the rotation real?

[@emrahatagan]

Hello 10:57 how did line make you blue

[@I-TingYen]

i think we should make convert entities first, then choose the line when you make the offset entities

[@DeepakSharma-dm5wv]

sketch ki PDF with dimenision kise download ho ghi

[@avdheshtiwari1073]

How to mirror used 8:12 please

[@AmanKozybayev]

awesome!!!

[@amyphillips1801]

What happens at 5:58?

[@vinny659]

How come i tried to copy the feature, it shows on the preview but once i pressed ok it disappears!

[@ratimachaberidze9453]

what is program name this loocks like REVIT

[@eslam841]

Solidworks 2014

[@grupoamecanica6157]

What I shoul do if I want to make a v8? thanks :)

[@hamadahoussien8833]

how i can download this video

[@dinozorskull]

FREEMAKE VİDEO DOWNLOADER

[@mohammadasri4395]

my sw crash when trying to cut at 11:16

[@konstruktionsmarktde9007]

Tol Tol Tol! Bist du Konstrukteur und möchtest du deine Projekte und Idee weiter verkaufen? Melde dich auf www.konstruktionsmarkt.de - Platz für deine Projekte!

[@TwiiOne]

10:48 !!!!!!!!!

[@Norman_Peterson]

audio

[@angrypotato97]

if u need audio to understand this, then go find tutorials for beginers

[@mahirkepic3273]

Hey at 14:14 do you filet all the inside corners or just the three you did?