Table Saw & Toggle Fence│DIY 쉽고 편한 목공 테이블쏘 & 조기대 만들기

E-mail : [e-mail]
Donate to dekay : toon.at/donate/dekay
It is dangerous to fix the circular saw with only the screw.
I added urethane bond and hardware to fix it.
Add a coupling device for your safety
목공을 취미로 하다보면
자주 쓰진 않지만 없으면 아쉬운 테이블쏘를 책상에 설치했습니다.
토글 클램프를 이용해 완벽하게 피팅되는 조기대도 만들었습니다.
기대 했던 것 보다 정확해서 꽤 만족스럽습니다.

[@ZXCharlieR]

Simple and effective,now all it needs is a dust collector!

[@leftthenright88]

no kick-back safety, it is too risky to lose fingers or get hit in the nuts/head by the wood thrown back at you

[@patrickwilliams6464]

This table is an accident waiting to happen

[@user-uk1kj2kc2h]

자제 설명도 좀해주시면 않되나요??? 제가 완전 초보라서요.

[@AnnArkhan]

What is your table clamp's name?

[@tvu111974]

It’s not bad but I’m a bit confused. So, this table saw (only) makes 90 degree cut??? Regular table saws are adjustable to make from 90 - 45 degree cuts. I’m sure if you make more cuts with the saw at various angles up to 45 degree then it should accommodate what I’ve addressed. However the manual angling of the saw would (not) be fun to mess with every time you have to make an angle cut. I do like your makeshift version of a sliding fence for your table saw. This video is entertaining but I’m not sure if it super practical for pro contractors.

[@namgunheo4738]

이렇게 제작해서 팔기도 하나요?

[@user-yk8ph3oh6i]

Hlo sir how are ypu

[@paripayeng5212]

How to make this table management ?

[@anythingaboutyourshelf8418]

What do you call the clamp for the guide

[@leiftismo2793]

Sir what do you call that holder/locker

[@user-if4sn3fo4p]

심플하고 효율적이에요 배워갑니다 좋은영상 감사합니다!

[@morbachpr]

Teu trabalho ficou simples e efetivo, faça uma caixa em volta da serra com encaixe para aspirador de pó, só isso para ficar 100%, abraços do Brazil

[@user-mi6ub7gy4b]

잘보고 갑니다 ^^ 조기대 고정 부분이 마음에 드내요 ^^ 목공은 잘 모르고 관심만 가지고 있는 1인 입니다.

[@plumberyunmoneytalk3415]

플로우님 영상 보다 들러봅니다. 한국분들도 많으시지만 외국분들도 시청을 많이 하시네요. ㅎㅎ 좋은 영상 잘 보고 갑니다. 감사합니다 😊

[@skdanceacademy]

와 이거 너무 훌륭합니다-! 따라 해보고 싶어요~!

[@rafezetter8003]

DK - if you add 2 small bolts with hex heads to the inner surface of the fence runner (the bit that runs along the edge of the table) at each end where the toggle clams are, you'll then be able to "tune in" the fence to be PERFECTLY 90 deg to the TABLE, by adjusting the bolts forwards or backwards - there are various ways to do this, but the most simple would be to draw a pencil line on the table along the fence, then flip the fence to the other side of the table and see how it lines up, a discrepancy will be obvious (it's the same trick as checking a carpenters square for "square". Once you've got the fence to a perfect 90 deg to the TABLE, then you can also fine tune the blade to the fence by just slightly enlarging the screw holes holding the saw frame to the table and making tiny adjustments until tha saw blade is perfectly aligned ot the fence. This is standard practice for setting up a table saw - having a misaligned blade or fence will cause unlimited poroblems until it's correctly set and aligned to each other.

[@Unclecarpenter]

진정한 능력자시네요~언제나 즐거운 목공하세요~^^

[@pwhite214]

Nice work. I would add a T-Track on each side for "feather boards" to prevent kick back and possibly a miter gauge and / or cutoff sled

[@saragogogerar]

정말 잘 만드시네요! 완전 프로 같아요 ㅎ 인정 ㅋ 인정 ㅋ 잘 보고 선물삼종세트 남기고 가요 ㅋ