Taking Apart Canon MG6320 Printer for Parts or Repair

[@ibariban]

I have a message "Ink absorber is full", but no explanation it is. Video clips are for other models that are completely different from MG6320. Can you help me, please? Thanks a lot

[@303electronics]

Hi. I understand why instructions may be different since this printer model has a touch sensitive control panel rather than the actual pressing buttons. I do not know how to reset it, but will update this answer if I find help for you after some research. I apologize for not being very helpful at the moment.

[@Anubis6175]

just got my MG6350 working again, didn't get past Error code 5200, not sure of original problem but once i ripped the side off and check all the cables to the PCB it started working again, nothing even look loose.

[@303electronics]

Glad it started working, thanks for sharing! Good work! Have a great weekend!

[@TheMagista88]

Do u know how to send this printer into service mode? Thanks.

[@calibar1]

wondering the same

[@robira1313]

All I wanted to do is clear a paper jam. It's under that big black panel on the bottom but I cannot get it off.

[@시나매]

I hope there is a specific decomposition video of the waste ink line.

[@randomdude420puff]

Looking forward to the reassembly video ;-)

[@Acecryz]

I have a MG7770 but I lost which wire goes where to the main board. Does anyone have a photo I can refer to? There's two types of 4 pin connectors one white and orange and I can't tell which goes where since they are close enough to plug into either and are both 4 pins. Any help would be greatly appreciated. Thanks!

[@303electronics]

Most wires should be different and one will not fit into the wrong slot. The printhead wires are same, but are in order and shouldnt cause confusion. I know it is a bit of a complicated job.

[@f.ferdhian7669]

Hi, is there any possible open the body without open the scanner? . coz only need replace ink tank waste pad

[@303electronics]

You don't need to remove the scanner, just skip to removing to portion.

[@f.ferdhian7669]

@@303electronics okay thanks for your advice 🤗

[@naniSinek]

Thank you very much. I followed your video and was able to clean my timing strip. Unfortunately I had also to remove the upper metal rail of the print head carrier. Do you have a video how to correctly remount it so that the print head is leveled again and the alignment is correct? Thanks a lot. Please need your help.

[@303electronics]

Hi. I have a similar model on which I'll try to show that. I'm sorry it took me a while to reply. First had to check if I have one.

[@303electronics]

Hi. Just posted this video on replacing carrier. I hope it helps: kzbin.info/www/bejne/aYKTq3ecpp54bbM

[@longintybur]

@@303electronics t

[@natsufire1667]

have the exact printer but its mg7570, but i says cpuld not detect ampunt of ink on cartridge. 2 of them. and ty

[@mos9676]

Hi is there a way to get into the absorber pad in a simpler way?

[@303electronics]

I am not sure, but possibly there is an easier way. I will look into that and let you know,

[@mos9676]

@@303electronicsHi again. were you able to look into it. My printer marks an error that ways ink absorber almost full but has not been able to figure out a way to clean it. I even tried to send it to Canon repair center and they just let me know that I need to buy a new one. Which is illogical because it works correctly and only shows that error that I don´t know if will affect more the use of it. Hope you can help me.

[@laurencelance586]

What to do for a paper jam inside the printer?

[@ar8594]

Hi, thank you for the video- I am having issues with the output tray not opening automatically. It gets stuck and I have to manually force it open. It also won’t close all the way. Does this mean I need to replace the output tray? And if so, do you have a video on how to install the tray? I can’t seem to find one.

[@303electronics]

Not necessarily. You can check the tab on the right and make sure it is on the correct position. You may remove the tray and reinstall it properly, but I doubt you need a new tray.

[@ar8594]

Hi thank you for the response. I have removed it according to your directions but the small tab that’s supposed to open when the tray opens is not moving with the white piece. How do I connect the two?

[@zinedv]

I have a similar printer and it doesn’t turn on. Any ideas on what could be wrong?

[@303electronics]

It can either be a bad printhead, main board, or a power supply that shorted your printer. Try removing the printhead if possible and then turn printer on. Sometimes.

[@zinedv]

@@303electronics thank you, I will try that.