EASY Common TV Repair for DLP !!!

[@MoshiDFA]

I'm not sure if anyone posted this but if you want to know why this happens, then keep reading. first the lamp burns out and you replace it. Sometimes a generic lamp is different in terms of energy and light output. Therefore the heat from the lamp is greater when it hits the mirrors, at levels that it wasn't tested for. Over time this "glues" the microscopic mirrors. The best way to prevent this is to provide the proper cooling. First clean all dust inside including fans AND the most important is to clean off the thermal grease on the heatsink and replace it with fresh and more efficient silver thermal grease. Not expensive and found easily online and in electronics stores. This allows less heat to remain in the DLP chip and therefore the heat leaves through the heatsink out the fan. Many computer guys would know this and this WILL prevent from buying another DLP chip or at least extend the lifetime. Hope this helps!!!

[@chris2028]

Very easy to follow, thank you! The only trouble i had was i tried it before i put the lamp.door on. Turns out the lamp door triggers a platic safety switch. So i was just getting a blinking orange light. I put the door on and the tv was fine. Its a blue switch just to the side of the fan. Your video was freat help 5 stars my friend. Go a little slower M on the screws when you pull them out i got a little confused on what screws went where. Thank tou thank you

[@edgarreyes4488]

Thank you, Your comment save me from spending a couple of thousand dollars on another TV I was having Issues with the lamp (Steady red light) so I order one from Amazon and didn't fix the problem, so I order a different one (A bit more expensive, and hopefully better quality) but figure not to put the plastic cover just to save time in case that the new lamp didn't fix the problem. So instead of a steady red light, now I was getting a flashing orange light so I thought the TV had reached his end, But then somehow GOD direct me to read your comment and Voila! TV is working like new. Thank you!!!

[@jayclas4023]

Hello I blew compressed air in my Mitsubishi DLP and fried the Ballast. I'm hoping to replace the Ballast and fixed the problem but thanks to your video I'm going to pull the entire light unit out and clean it!

[@PoeLemic]

Mine just went out for my Mother's TV, so I plan to replace it. The dots were getting bad, but we were just holding on. But, I am going to use your strategies and save some money. Nicer TV's have arrived, but I want to push this one as far as possible. Because Comcast cable box isn't 4k yet, so I'lll upgrade when 4k's get added to our cable box. Again, thank you for really showing us how to save money and protect our family's income. Much appreciated ... Very good job !!!

[@daledonaldson2295]

Hello and Thanks for All you do. I've had DLP TV's for around 20 years now. I just replaced the bulb in the one I have now, Mitsubishi Diamond Series WD-82842, it did burn out. Bought an OEM, worked fine for about a month. My TV, this morning will turn on, but no Video at all, checked the bulb, seems to be fine, no blown filament or glass. Can a bad DLP Chip cause no video or a bad circuit board, or even yet, dust, I have not taken the back out yet? Looking forward to your reply over in Central Florida :)

[@senorv6]

Great Video! How about the white and black dot issue as well as a flickering background of white lines? Is this issue associated with having a bad DLP bulb?

[@JohnnyDesaint]

Great video.mine the center blue light lit along with the red stand by temp and the green lamp light.the screen does not turn on

[@Joey-hv4yq]

I did this repair about 7 years ago on a 7 year old LDP TV. I was a little intimidated at first. But the hardest part was making sure I labeled plugs and recorded the disconnection of the plugs to make sure I knew where everything went when putting things back together. One mistake I made, was that I did not screw the DLP lamp door completely closed just in case it did not work and I had to troubleshoot some more. So I plugged the TV in and turned it on and there was NO PICTURE! The TV would not turn on. I assumed I screwed something up with the chip replacement. However, I noticed a yellow light blinking a code on the front of the TV. I looked up the code and saw it was telling me the lamp door was not closed completely. This is a safety feature to prevent you from burning yourself on an extremely hot lamp. When the screw is all the way in, it activates a small safety switch which then allows the TV to turn on normally. I WAS SO RELIEVED and so was my wife. But replacing the actual chip itself was easy. Great video! The TV is now 14 years old and still going strong with a very nice picture. I hope I didn't jinx myself. LOL

[@grnicanet4969]

my is about that old wd73737 , now just blinking red and bad smell, burning something any body , any ideas....???

[@joedpl]

Excellent video, made cleaning the fans on my DLP easy.

[@TampaTec]

those are sustain boards in plasma tv, no video but sometimes audio you might get. if you got good dc volts to those boards buy x or y boards at shopjimmy website.

[@Mrbob111]

Have had a WD-65738 for years and still strong at 8100 hours (knock knock) . I had a problem now with no sound on left speaker. Connected an external audio source to both speakers through the side service holes and both have sound. Is this a board and is it work repairing??? Thanks and great videos.

[@everythingrosey4813]

hi, I watched your videos and they are great ,but I can't fine anything on my particular problem. My TV screen continues to show half screen left side show vertical lines and the other side is normal....i spoke to a expert and he said its the Pcb . I already purchased a lamp and a color wheel

[@SheriTyrrell]

If I heard you right, the dits could be caused by a bad connection at the lamp? My lamp went out and I ordered and replaced the bulb. The tv started working almost instantly, but we started getting white dots right away. Then they got worse to where now it looks like your in a snow storm. Could have I caused it? Or should have I replaced the chip at the same time. Also there was a chip that looks like this chip next to the bulb. In fact. Had to remove the chip to remove the bulb. What chip is that?

[@Raiders757]

My 2011 Mitsubishi 65" DLP has worked great thus far. had to replace the bulb one time already, but that;s no big deal. My main issue is that I am hearing a faint whirring sound that cuts off and on like it's a fan winding up and then cutting off over and over again. Could this be a dirty fan, and can I clean like I to my PC tower in order to quiet it down?

[@MrApplefarm]

Thanks to videos I have replaced a lamp and a chip in the past on my older Samsung DLP TV. But now sometimes (not always, but more frequently lately) when I turn on the TV I can hear sound but the image is stuck looking like one of those computer-generated 3D art images, with the same mish-mash mostly green image repeated in rows and columns. It seems to correct itself eventually by turning off the TV, waiting 10 seconds, and turning it back on. Sometimes It takes multiple on/off cycles and sometimes I wait longer between turning it back on. Sound familiar at all, and is this an issue for replacing the chip or something else? Thanks in advance!

[@EvrydayErik]

I took out 2 screws most videos show, but the light engine won't slide out. Stuck and feels like there is another screw. Any Help?

[@Spartan9299]

Worked great! Thanks!

[@omarmcclary843]

I replaces my DLP chip in my Mitsubishi tv and it’s showing better than ever except for the fact I now have two black lines in my screen

[@jasonthejawman5442]

Great Set... I stay away from DLP TV's LED Sets are Better... The repair is great good Job

[@mr.markj.moorer450]

Jason Cruz

[@michaeljames2056]

Where do you plug in a optical cord on a 73" DLP tv for your sound bar to work?

[@peerlessroger]

what would cause lines across the screen horizontally to happen? It's like the picture is going out. not the dead pixels problem I fixed a couple years ago

[@nightspeed98]

HI Tampatec, i repaired the white/black spots on my Mitsubishi 73" DLP few months ago with help of ShopJimmy. now it won't power on. i get a crackling/sparking/ratcheting sound and then nothing. thoughts?

[@justinb5759]

Do you have a video on how to repair the screen if it's slightly tilted (crocked) picture shows just fine, in fact I just had the chip replaced. I moved the tv to another location, plugged it up and the screen was slightly shift with one side higher than the other.

[@bobbypeterson1266]

i have a mitsu 1080p, 60735. replaced the dlp chip and it worked great for about 3 weeks and then the screen went black. I replaced the lamp but did not fix the problem and I still have audio. what can i do next. thanx for the help with the dlp chip and this problem as well, hopefully

[@VaughnDecker]

Hello Tampa tech I have a Mitsubishi 82738 dlp TV I replace the bulb powers on no picture no error codes flashing what could be the problem do you make in home repairs

[@belartful]

screen is a bit flimsy and pushes inward (causing an hourglass shape to the image) any DIY fixes for this? i was thinking maybe gluing in some wooden dowels, but not sure how well that would work unless there's a common way among the community to fix this :P

[@jameshass1791]

How do you fix a Mitsubishi projection TV that got a power surge or strike by lightning. I have a power surge protector.

[@brendaqualls8709]

Is there any way I can just clean the DLp Chip before I purchase one for my Mitsubishi WD73C9 tv I only had this tv for 4yrs , but I had it in storage for 2yrs, I have replaced the bulb twice since I had it

[@nin4ever1]

When I turn my tv on it makes a high pitch noise that seems to rise and fall in volume. It does this for about a minute or so then turns off. The screen stays black with no sound. I’ve checked the lamp and it seems to be fine. Do you think it’s the chip cause I’d hate to waist money!

[@smell5118]

Hello i have a toshiba DLP 62HM95 i have had this tv for 11 years the picture was beautiful now its bad the color is it the color wheel or the chip thank you for your time oh the lamp is find

[@TampaTec]

thanks, DLP TV lost out quick out to LCD & plasma, LCD or LED is my choice of tv too. but my Next few videos are plasma, lcd and LED tv fixes too. 8^)

[@hevanrichards2237]

Do you have any advice for a wd 82740 dlp tv? Ours has developed black lines on it.

[@JavsfromChiTown]

Great video! I replaced the DLP chip on my mitsubishi wd-73735 tv but when I plugged it back in there was only sound and a black and grey bar screen with with horizontal lines. I checked everything 3 times and still can't find if I put something back wrong. Any ideas as to what went wrong? Thanks

[@TampaTec]

some dlp mitsubushi TVs have extended warranty on dlp chips. Mitsubishi- phone: [phone]

[@mr.markj.moorer450]

javier franco

[@kevinrumsey3735]

I have JVC 65" with strange red or out of color of sync letters in the menu . How do I adjust the ventricle or horizontal holds on this 2003 model AV65WP74 and have a better picture to look at. Kevin.

[@scotttrottier2833]

I have a 62 inch toshiba dlp tv and there is like a floating web or something inside that you can see on the screen which looks like it would be outside but it is inside. IIt looks like a two thin flowers moving in the wind just off center to the right of the screen. Is there a way to get inside to remove the dust from the back of the screen or is something else causing this?

[@CK2012]

I do not have this TV I have the HL61A750, Had my TV chip replaced by a tech about 3 years ago, it is almost 10 years old now still going strong, The LED's may go out soon I have some on hand about how long does the TV holds the charge after it is unplugged?

[@charlesmayo4933]

I have a Mitsubishi 60" that has a washed out screen on the bottom and up the sides. I have cleaned everything and replaced the bulb. Any idea?

[@robertdonlan8193]

hoping you can help, i have 2 of these DLP TV's, wd-y65 and I'm getting error code 39, i have cleaned all fans, new dip chips, new thermal sensor, still same issue, powers on for 30 sec to a min. then shuts down, solid yellow light, tv will turn back on after reset but just shuts down again, with error code 39 this has me stumped I was hoping to use parts from both to get at least one of them working again, i searched and everything i found online says air flow restriction and to clean it out or thermal sensor and I've replaced them too , I'm starting to think its a problem on the logic board but wanted to check first before i caused any additional problems, any suggestions? thanks rob

[@TL-xl8df]

I have model WD92840 and I’m getting 6 red blinking lights and 1 yellow blink, then it repeats do you know what the diagnosis is?

[@o0obonga]

I have a mitsubishi DLP with a horizontal rainbow, I changed the bulb hoping that would solve the rainbow and now there is also a rectangular rainbow on the right side in addition to the horizontal rainbow. Any idea whats causing this?

[@debbietroxel7713]

Hi. I have a 73 inch mitsubishi tv wd 73733. I am getting a flashing green light, then it goes black. No more lights. When i turn the tv off, i get a steady red light. Wont go off unless i unplug the tv. I have been told that one of the three cooling fans are bad. How do you know which one? Any help would be greatly appreciated.

[@starballenger5618]

Is the red light under the lamp indicator or all the way on the right?

[@imeldamalajacan3781]

debbie troxel 9p

[@douglaseaton1581]

I've got a 50" led dlp from samsung. Not only does it have white dots appearing, but there has been a "dark vertcal line" on one edge of the screen for at least a year now. The picture still shows through but it's kinda greyed out. I don't know if both problems are from the same culprit or more than one component is faulty. The tv is probably close to 10 years old. With advances in tv tech, does it really make sense to invest in trying to fix a dlp tv?

[@douglaseaton1581]

I can't imagine oem parts are even available at this point for a reasonable cost.

[@vtxvick1333]

Do you have a video on how to fix a black screen , its on and sound but no images.

[@et94303]

Will a video board be y-board or x-board? On a ph50 vizio plasma

[@thomasswitzer3876]

I have a VIZIO M260VA 32-Inch Class RazorLED 720p LCD HDTV with red and green dots that cover the screen obstructing the view on startup. After a few minutes they subside and then become widely scattered dots of the same two colors ?

[@davidrowe4909]

My image is fainting. Still visible, but horrible watching tv with any room light. No issues turning on. Bulb or chip? BTW this video is awesome

[@OldschoolLo]

that's going to be bulb, very simple to do we've had to replace our bulb a few times

[@OldschoolLo]

also when you get the new bulb set settings to cooler and energy save mode bulbs last longer

[@davidrowe4909]

Awesome. It's sitting on the sidelines right now awaiting a new bulb. Know of a good place to purchase these?

[@OldschoolLo]

+David Rowe we just Googled local places that sold them we got ours at a place called crown tv

[@janiceshaffer5482]

+David Rowe amazon 34.00 dollars light for mitsubishi tv I bought one for my 65 inch

[@myname2263]

I did this , but ended up messing with the geometry settings in service menu , do you know how to get the TV back to default settings ?

[@Skatersesh10]

I have an issue with a WD-73833 Mitsubishi DLP 1080p. When I turn it on , the audio sounds like it's popping almost as if it's like a record player when the record player skips the record, idk what the problem is, when I watch a show the audio will skip as if it sounds like it's muting /popping every 5 seconds or so

[@scottfromoahu2896]

hey. samsung dlp in Tampa left sitting for years.turn on and vertical hold off. picture appears to be stuck in cycle from bottom to top. any advice?

[@onebadbum]

I have a very important question, I just bought my Samsung DLP TV (55" Don't know what model besides it has 3 HDMI Ports PC ports, 3D port and basic ports) and when I turned it on (Don't know if this is a sign of a problem ) the Temp. light is Red solid for a while but then the lamp light (infront) is green and blinking. It makes the sound of coming on but the problem is the screen doesn't work nothing pops up. Any ideas? My guess is the actual lamp needs replaced but I don't entirely know. The lamp lightbulb comes on so could someone possibly help me?

[@cristianalejandro8911]

hey man what do you do if u already replaced the lamp on a 70 in jvc projection tv but it still looks dim?

[@thomasbolton2121]

I get Blue and Pink static on white or gray background during shows and movies.. What could cause that? thx.

[@MICHAELBRANDTTrashcan]

i have a 32 inch lg tv works great except the sound what or where do i look for the problem somtimes i get volume but crackly and hardly hear it iv changrd most capisitors and video board same problem though

[@ldl0021]

I need one of these for a hitachi 55 inch DLP television...

[@bigdog8882]

Good Video Bro!

[@arniecan8531]

so the dmd board is the same as forematter board?

[@LukeJosiah]

My samsung hl61a650 won't fully power on. It has power to it. When I press the power button the t.v. powers on. The audio sound starts, the lamp and color wheel turn on. All seems well for about 3 seconds. The lamp quickly turns off and tries to power back on but comes back very dim then turns off completely. The television then goes through a power cycle where it all starts over again. This process happens for infinity till I unplug the machine or active the safety switch for the lamp housing. I've replaced the DMD board, lamp, power supply and ballast. The only thing I haven't replaced are the computer chip and the main board. Any help would be greatly appreciated. Thanks, Luke

[@neptuneruler28]

Luke Tilton Did you ever find out the problem with your Dlp?

[@midnitetoker3042]

top 12 inches of screen slightly darker than rest of screen ..... replaced bulb ..... any suggestions?

[@gilsmith3738]

Where do you get the chips

[@rashidahwise2158]

my 32 inch lcd and dvd combo has a blank screen flashing black blue red and green what doese that mean? is it fixable?

[@tmogilnicki]

I just replaced my bulb yesterday. cleaned it all out real good. turned on my set, it comes on but after about 3 to 5 minutes, it shuts itself off

[@tmogilnicki]

any ideas why

[@lelandrobertson9964]

Try resetting and check blue power switch by bulb door. Fixed mine.

[@MegaSurfgod]

Use electrical tape and tape down the blue plastic wheel , this will heat up and continue to shut off tv. over and over. Can be very frustrating. Speaking from first hand experience

[@tonim8669]

@@tmogilnicki buy USB fan plug it in keeps TV from overheating.

[@StinkyBeans]

Should'nt there be some thermal paste between the heat sink and the chip?

[@TampaTec]

true great eye, i will add a speech bubble in thanks, that will help transfer heat away from chip to heatsink using heatsink compound.

[@Patte157]

***** where exactly would I apply the thermal paste? does it just get applied all over the under side of the heat sink? sorry I have no clue about all this lol :)

[@77dddraiders38]

im getting green scribble lines on my mitsubishi 73" dlp any suggestions what it might be? thank you.

[@darrellrosales7793]

This is happening to me now. What was the problem and the solution.

[@leowatson1580]

Thank you you've been great help

[@cspawards]

Do u know how to fix if the TV shuts it self off...

[@TampaTec]

Check TV eco energy saving settings but if your TV is over 10 years old it can be bad capacitors in power board. Get TV boards at shopjimmy.com 👍

[@arniecan8531]

tampatec Whtas the difference between dmd and dmb board.Itook my tv to the repair shop they told it was the dmboard.thks

[@TampaTec]

DMD is video board with dlp chip on it, And DM board is video board too but with video inputs on it, but never heard of DMB board maybe they meant DM or DMD.

[@TampaTec]

first replace batteries then unplug powercord on tv for 1 min to reset tv, call for ir sensors 1 [phone] / [phone]

[@LADYTECH60]

Great video guy!

[@Santifiu]

Que precio tiene la pieza que se le cambio y como se pide para comprarla

[@mikebishop3771]

hello. I have a mitsubishi WD 65838 dlp HD TV. I recently replaced the bulb. now when I turn it on, it works perfectly fine for about 20 minutes. then it starts strobing green and purplish colors on all settings. do you have any information as to what causes this and how I can fix it? please help. thank you.

[@randykruger9710]

Hey Mike-Same problem..No answers here. Bought a new bulb,What did you finally do?

[@Whitese7en]

What are the symptoms of a bad lamp?

[@TheWendalls25]

How about a high pitch buzzing? Any ideas?

[@TampaTec]

+Wendy Justice Can be bad filter capacitors in main a/v board or power board or transformer.

[@TheWendalls25]

+Tampatec thank you for your input, really didn't want to get rid of a perfectly fine flatscreen without at least trying

[@TampaTec]

happy to help, sub and follow me on G+ for free tech support :)

[@adonissepquin]

If the buzzing occurs after you've recently turned the set off and turned it back on, that's normal. I have the Samsung 56" DLP HLT5676SX and it happens to me when I do that. The sound is normal.

[@edwardkim3854]

Wendy Justice

[@fededej]

Help! Had 100+ tiny white dots replaced chip w yours now have 25+ vertical white lines top to bottom !

[@dimplesjackson3080]

I have a 65 inch LG big screen power button blinking red light blinking sound or pic have do i fix it

[@ivonrobledo6512]

I have a 60 inch Mitsubishi dlp. When I click on button the status light blinks green continuously but screen does not come on. No sound comes from it either. Would I need to replace the chip on it or the lamp?

[@bigcee65]

Ivon Robledo Did you ever find out how to fix this issue? I have the same problem and I've asked before too but no one ever gives a solution.

[@neptuneruler28]

Ivon Robledo I have the same problem did you find out what it was?

[@Skatersesh10]

I have an issue with a WD-73833 Mitsubishi slip 1080p. When I turn it on , the audio sounds like it's popping almost as if it's like a record player when the record player skips the record, idk what the problem is, when I watch a show the audio will skip as if it sounds like it's muting /popping every 5 seconds or so. Please help asap

[@musicmaker4the1]

Great video. Clear instruction. Step by step. Along with the replacement part from shopjimmy, my TV looks brand spanking new!!!! Thank you so much for this video. Well done!!

[@Gearsofwarplayer555]

I have a wd 73737 mitsubishi tv shuts off after less than a minute. It will turn back on then shuts back off. The red light goes solid red, no flashing. It did start having white spots a few months before this.

[@davide4680]

Hello, My Mitsubishi 65" is doing the same thing. Comes on, picture shows, ~ 15 seconds later it shuts down. Then I wait about 15 seconds and turn it back in. 15 seconds later... it shuts off again. Help! Curious is you received a response. I didn't see any response to your problem If you fixed yours, would you share what you did? Thanks.

[@mdmd-qt8ch]

Freestorm Seabreez i have the same tv as you, mine was doing same until lamp went out and just replaced the lamp and it stopped but now i have the white dots and have to replace the chip, also had another tv did same thing just was too much dust

[@scottschmitz6061]

I have a Samsung hl67a750a1fxza dlp and once in a while when I turn it on the screens all red tint then goes back to regular picture. What could this be

[@richarddude1]

hi, i have a samsung sp50L 7hx, picture goes off after 20 minutes but sound is ok i suspect overheat problem what do you think..new bulb? just a clean? or could it be some thing else..thanks

[@TampaTec]

common issues is lamp, dirty/bad fans, bad color wheel, bad dlp chips, then bad capacitors in power board like 1000uf, 2200uf, 3300uf 10v or 25v, go to Shopjimmy.com or 1 [phone] / [phone] for TV parts

[@mr.markj.moorer450]

Tampatec

[@thedisposableheroesmcgta5683]

Thanks!!

[@peterspokus3761]

I replaced lamp on Samsung dlp. it worked for five hours now TV shuts itself off and on. sound with no picture. any thoughts. thanks so much. very frustrating

[@trancendedsoul]

Same situation here but with a Mitsubishi but after 1.8 days of continuous use. It shuts off and blinks red constantly or with added fans it just shuts off and stays solid red after replacing the lamp. I just got done cleaning out the entire unit tonight so I am in the process of eliminating dirt and dust build up which would create some problems including this from what people claim on the Internet. So far this is still not a solution though. I will RMA the lamp and then try a new ballast next. If anything works I will let you know. I have searched for hours and found the top 6 things I have found searching for a week are: 1: bad lamp, 2: dirt clogging up or slowing down fans, 3: ballast needs new caps or is damaged, 4: door switch heats up and becomes faulty causing it to stop, 5: the thermal sensor under the color wheel or the color wheel itself needs replacing, 6: resetting lamp timer manually.... I am going to finish testing this to see if I can fix it. If I figure this out, I will post some information.

[@williamroman9460]

Great video.....

[@edwardecko]

I don't have. On my screen but the TV only stays on 4 15 to 30 seconds and then turns off the turns on but nothing comes on the screen would you have any idea what it could be.

[@orengellharper8180]

i have a 55" Mitsubishi smart tv that wont come on but its blinks 4 red and 8 yellow what can i do to fix it

[@tdrlsb]

I have a green blob on my sony dlp...about 3 inches roumd...how can I fix it

[@TampaTec]

check video board (the one with dlp chip and fan)

[@iowaland7658]

What about only an occasionnal picture. Has sound but no picture

[@johngardner2407]

After replacing my chip and reassembled. TV will not power up. I have a red static light.

[@blainegwen4858]

i have 2008 wd65831 -- i get error code 59 which says "dm short detected" -- im thinking its toast but i dont even know what the 'dm' is -- could it be short in fan?

[@TampaTec]

[@nspectrmustache]

Tampatec my Mitsubishi wd7373 is doing a few weird things and I need insight as to what may be wrong with it. The screen will randomly make everything have a green tint, sometimes the picture will scroll very fast from side to side or up and down, other times it will shrink the picture down to half of the screen making the other half black and lose color making it black and white. These are all intermittent issues and do not all happen at once. Any help would be wonderful thank you!!

[@billyweems4984]

Tampatec i have a question how can i send you a message

[@NunYa953]

Tampatec Shop Jimmy doesn't have the DMD chip in stock for my Mitsubishi and hasn't for a long time. Where do you recommend I look for one? It's gotten to the point where unless I'm watching a hockey game I can't see anything through the white dots.

[@salceti]

***** Great video and precise instructions Keep it up

[@enzodunn2577]

What would cause green and pink squiggly lines moving around on my dlp

[@zacbond8833]

i have a Samsung 61 white dots and then it just completely cut off is it the DLP chip

[@jalensweet579]

w what do I do if my screen is tilted a little what I be able to fix it without doing all of the disassembly

[@daviddavies9909]

Hello can u help me how do I fix my TV screen its flashing black

[@seaview1776]

No thermal paste between the heat synch and the new board?

[@therhetoricalman8936]

Correct

[@garybutlerjr]

I'm having a problem with my dip its giving me a code 61 and some times when i turn it off it makes a loud buzzing noise any ideas

[@joeshmo4929]

HEY GARY, JUST SAW YER POST ON TV REPAIR COMMENTS SECTION AND I HAVE SAME PROBLEM. I KNOW ITS BEEN 8 MONTHS BUT DO YOU REMEMBER WHAT THE FIX WAS AND MAYBE ALSO WAS NOT ? APPRECIATE ANY HELP BRO ! THANX

[@garybutlerjr]

It was the color wheel I replaced it and it fixed the problem

[@arniecan8531]

hi tampatec i have a dlp wd-65831 65' mitsubishi i just replaced the lamp and cleaned dust bunnies and air flow passages after 20 minutes the screen flickers briefy and then i lose video tv stays on b-cuz i can hear audio i let it sit for a while and i get video again but after 20 minutes it does it again thks in advance

[@TampaTec]

Call mits- 800.332.2119 Cause i think that tv's model DMD board had extended warranty. DMD board "might" be free www.city-data.com/forum/consumer-electronics/1162259-white-spots-mitsubishi-rear-projection-tv-9.html

[@MightyMansion]

I have a Vizio 55" flat screen and I had it for a long time and it's been having lines across the tv and just now a quarter of my screen went dark then started blinking normal with a bunch of lines... And right now the quarter bottom came back to normal with a yellow black tint and now it's flashing again... Any way to contact u

[@trancendedsoul]

Sounds to me like the screen is going dead from forcing in the wrong vertical or horizontal frequency. The T con board is unlikely as it has horizontal lines.. I had several TVs have that issue in the last 10 years. Sadly most TVs are made very cheap and are likely throw away's within 10 years for many people. try googling a new TV with a low number of complaints regarding equipment failure. It is very hard to find any model right now that is not loaded with 5% complaints or more after being on the market for one year. It is time to buy a new TV for you. Your old one is not worth repairing unless you want to spend $800-$1500 on screen replacement they do not even make anymore..

[@charles-bigchazz-herrera3582]

I have code 57 on my Mitsubishi 73638 model

[@carrillokimberly55]

have you ever fixed a micro sd memory card? i really need your help if you've have...

[@TampaTec]

if its cracked it maybe permanent if contacts are damaged but most cases its dirty or dust on sd card contacts or dirt inside sd card port preventing good connection so just blow out dust inside port, but some sd cards have lock switch to prevent deleting data.