TCM Transmission Control Issues on Mazda 3, Mazda 5, 2006 - 2015.

[@patrickclark223]

I had my TCM replaced by Upfix and it fixed my shifting issues. saved me a lot of money. I have 1 question. Can driving on a faulty TCM cause speed sensors to become faulty? I ask because my 2010 mazda5 still has a hard kick into 1st gear (this is also after getting the transmission rebuilt recently as well) and the speed sensors are the only thing in my mind that could still be the problem

[@upfixauto]

The sensors won’t go faulty by a bad TCM. However, continuous hard shifting can degrade the life of the transmission assembly itself. It’s best to get the TCM as soon as possible, especially if there is hard shifts present or the vehicle is already in limp mode.

[@reuvenwachtfogel7012]

So I have these kinds of problems (2011 Mazda5) but they come and go. Also the engine light is sometimes on and sometime off. Specifically, everything will be working fine and then, usually during a long drive: 1) Gears will not automatically shift 2) I move to manual shifting and sometimes that helps for a while 3) Often it will stick in 5th gear at this point even if I try to manually shift 4) The panel may flicker or show nothing And then the problem will often go away on the next drive. I have a cheap OBD2 reader which confirms LOSS of communication with TCM. I took it to a local garage and they tried to fix it but did not succeed. I'm guessing either: 1) that the fact that the problem comes and goes makes it harder for them to find the problem and be sure that they fixed it 2) OR they are looking at the wrong place and the TCM is fine but something else causes this intermittent communication problem.

[@upfixauto]

This is a common issue for Mazda 3 for this year range. The TCM unit is starting to slowly fail and causing these issues. The transmission is almost always good, the TCM is mounted directly on the transmission and the heat transfers from the transmission directly to the TCM unit causing it to fail. We do offer a TCM repair service and an exchange as well

[@weldean46]

Have a 2008 mazda 5 with a issue of a hard forward engagement at times and sometimes it goes in Normally with no problem, trans has been gone through and solenoids have been replaced and valve body rebuilt question is have you guys had many complaints about this problem

[@upfixauto]

yes this is a common issue with these Mazda 5 TCMs. See this link: www.upfix.com/product/tcm-mazda-5-2007-2015-transmission-control-module-repair-tcm-tcu/ Hard Kick on Drive & Reverse Hard Kick On Reverse Hard Shift From 1st Gear to 2nd Gear Issue Hard Shift From 3rd Gear to 4th Gear Issue Hard Shifting Issue Harsh Downshift Issue Harsh Gear Shifts Issue

[@emilyrizzo6589]

I'm looking into ordering this part. Personally don't have the knowledge of replacing the TCM myself. Thought about taking it to a Mazda dealership and have them install it. Probably not the best idea, but there isn't anyone I know or trust that can do this for my vehicle.

[@upfixauto]

So the dealership can install it, but we recommend your remove it yourself and install it as you will save yourself quite a lot of money. $500+. You certainly can have them remove it for you and then send it to us to repair. Just make sure when they reinstall it they don't mount it where the previous one was or you could get the same problems again. Here's some information on removal: blogs.upfix.com/mazda-repair-near-me-best-auto-repair-service-that-ships/mazda-tcm-removal-instruction-guide/ Here's some information on installation: blogs.upfix.com/mazda-repair-near-me-best-auto-repair-service-that-ships/tcm-install-mazda-instruction-guide/ We actually offer a same day service so your vehicle wont be out of commission for to long.

[@azulmarinoify]

Do you live in California?

[@azulmarinoify]

If you do live in the bay area I would help you with this.

[@emilyrizzo6589]

@@azulmarinoify Unfortunately I live in New York, but greatly appreciate the offer 🙏

[@azulmarinoify]

Oh I see it ! U are welcome !

[@rickpinili]

Hello , I have a question about where to install the new one or replacement TCM. Do i put it back from its original place ,under the battery frame or i heard something that you said ,,,is to install it or hook t up on the brake line? Thanks and i'll wait for your response and be safe out there..

[@upfixauto]

Yes you can attach the TCM to the brake lines that are next to it by using zip ties.

[@niridan6339]

"I have a Mazda 5 from 2010 with an automatic transmission. Sometimes, when shifting from 2nd to 3rd gear, or when downshifting from 3rd to 2nd gear, there are loud clunking noises and the car vibrates severely. It's especially difficult for the car to shift from 2nd to 3rd gear. The issue also occurs occasionally when shifting into reverse gear."

[@upfixauto]

yes this is a common issues with Mazda 3 and Mazda 5. The TCM unit is failing. It needs to be replaced or repaired. Here is more info on repair: www.upfix.com/product/tcm-mazda-3-2006-2014-transmission-control-module-repair-tcm-tcu/

[@radzer0966]

We got ours installed yesterday. Seems to have fixed all the issues but the AT light went off than came back on after about 4 miles. Clear codes and it pops back up. Any suggestions? We did a drain and fill with a filter as well but no slipping or anything crazy that we would consider transmission related.

[@upfixauto]

What codes are you getting?

[@perazo78]

I went on line to order this TCM but the price is not what you state on the video, plus there is a$100 upcharge for TCM programing/update that you must get when buying this part

[@upfixauto]

If you send your original for repair then it is just repair cost. If you need one immediately then there is a refundable charge and programming fee to your vehicle.

[@victoranderson1264]

I'm being charged $300 for core plus an Extra $100 programming + waiting more than 1 week for service. Still waiting and trusting that this will work.

[@peshmadscientist1833]

Im out of your area and would like to try to attempt a repair on a mazda 5 2010 L39C 18 9E1D . Have some silicon removed from tbe edges of the board. Can it be lifted out? How did you clean it up so well? Care to share? A solvent? I repair electronics daily and would like test any caps maybe found on the other side and check for bad solder, etc. .

[@upfixauto]

Microblaster works well

[@marcj2651]

Is the Shift Solenoid electrical fault could be a TCM issue aswell? Symptoms was hard kick on R and shift to 3rd gear even when I put on ditectly to D. Tried erasing the code it was ok for a bit but then after couple minutes of drive fault comes back again. Please let me know if it is related to TCM issue.

[@245artist]

More often than not, the TCM itself is actually at fault not the solenoids. Especially if you're getting the DTC codes that are commonly related to the TCM failing. UpFix has all the codes listed on the website that you can check out right on the product page. If those codes are the ones showing on your scanner chances are, the TCM will need to be rebuilt.

[@upfixauto]

For sure

[@edwardgabotswegope7235]

I can't locate the module under the battery fort Mazda 2 2004 harshback

[@edwardgabotswegope7235]

Please help

[@derrickforrester103]

Hello Up Fix . Where is TCM module located for mazda 5 2005. Removed the battery cabinet and there's no sign of a module .

[@upfixauto]

Some of the Mazda 5s dont have TCM module

[@jairolivo7685]

I have a 2010 Mazda 3 2.0 and it recently got a AT light and a check engine light with the code p2709 shift solenoid f electronic. When going into reverse there’s a hard kick, and it won’t let me check what gear it’s on when in Manual mode. It’ll just say “M”, Should I start with the solenoide or what’s your thought?

[@upfixauto]

Yes, it is very common for these Mazda 3 TCM units. It is faulty TCM. Needs to be replaced or repaired. Check out upfix.com

[@porry6941]

Hi I have a similar problem here with the Transmission Control, hmm i think so. It´s an 2012 Mazda 5CW. Do you offer the service worldwide as well?

[@upfixauto]

Sorry, currently offering shipping to USA address

[@dziggy3004]

What about CX-5 2024 TCM's? Mine is missing SHIFT from 2nd-to-3rd on morning drive (for about 5 minutes, then all is normal)

[@upfixauto]

No that sounds like something else. Yours is too new 2024 to be having issues like that

[@ИльяЛогинов-б8д]

Hi, I have a problem, the cruise control stopped working on my mazda 3, the master said that it is tied to the tcm block and needs to be repaired, tell me is it so? I was also lent the lfs3189e1a unit, but the cruise control did not work with it, it is with the Japanese mazda axela, what should I do?

[@lonzellflemming9516]

We got a2010 Mazda 5,I am going through the same thing,to where the gear is shifting and dropping, how much is it going to cost

[@upfixauto]

This is a common issue for this vehicle. Currently it is $329.99 Here is more info: www.upfix.com/product/tcm-mazda-5-2007-2015-transmission-control-module-repair-tcm-tcu/

[@howardlewis4148]

I have a 2006 Mazda 6, stuck in third gear hard kick in reverse ATL on or ATM on of those, but, only third gear. Am from Jamaica 🇯🇲 could I actually send it to get repaired?

[@upfixauto]

Yes this is the common issue. We can rebuild this TCM.

[@jenniferorrill1566]

What about a 2005 Mazda MPV? Intermittently acting like it's in neutral while driving. Overdrive light flashes. It's showing transmission codes p0706 and U0073.

[@upfixauto]

No sorry we dont do Mazda MPV at this time

[@sattilus]

Hi. Are you shipping to UK?

[@upfixauto]

No, not at this time

[@lizettegonzalez4074]

Hi, we have 2010 Mazda5, the Transaction Control Light is on, AT light is on, wont move and will jerk, but after 10 mins the lights will turn off and will run normally. Loose Cables? Or TCM failing?

[@upfixauto]

Yes, this is your failed TCM for sure.

[@virginialee4057]

I have a 2008 Mazda 5. I know it’s already 14 years old, but seeing if I can hang onto it longer. Currently the AT warning likes go on for a few seconds and then turns off. For those 2 seconds it slips gears. We have taken it in to a transmission place. When they do a diagnostic test nothing shows up, so they can’t do anything. Can it be the TCM, even though the AT warning light doesn’t stay on and no diagnostic codes show up? Can I do the exchange program and have my mechanic replace it?

[@upfixauto]

It sounds as though the TCM could be beginning to go out. You certainly can do the exchange program and have a mechanic replace it. You could save yourself $500+ by doing so yourself. The removal and installation is very easy to do and can be done in less than an hour. Here's some more information: Here's some information on removal: blogs.upfix.com/mazda-repair-near-me-best-auto-repair-service-that-ships/mazda-tcm-removal-instruction-guide/ Here's some information on installation: blogs.upfix.com/mazda-repair-near-me-best-auto-repair-service-that-ships/tcm-install-mazda-instruction-guide/ We actually offer a same day service so your vehicle wont be out of commission for to long.

[@gallo23]

Hi, I'm glad I came across this comment! I just started to have the exact same problem with my 2012 Mazda5 😐

[@gallo23]

Although, I checked the transmission oil and it's black and stinks as if it was burned 😳

[@gallo23]

Not sure what to do 🙁

[@fabianjimenez9163]

Hi, i just bought a 07 mazda with a bad engine. engine has been replaced but now it wont move on D or R nor in any gears No weird noises it just wont move I had it on idle for at least 30 min and transmission fluid didn't even get hot (80° max) Could this be tcm issue? Btw no check engine or any warning light's on the dash Thanks

[@upfixauto]

Thank you for reaching out. The engine swap is more related to the ECU. If the ECU (replaced or original) has already been programmed to the car's VIN then no programming is needed. The TCM already has the original VIN and should be good to go.

[@TJ-so8kv]

My son owns a 2006 Mazda 5 automatic transmission. He needs to warm the engine before start shifting in to Drive, if not the AT light will turn ON and the numbers starts scribbling. The ATF and filter has been changed. We tried to locate the TCM. everything that we watch is located under the battery, but there is no TCM there. Is there any other place where the TCM is located. Thank you. Keep safe.

[@upfixauto]

If you have one, it will be under the battery. Yes, we have also heard and come across some Mazda 5's that dont have the TCM unit.

[@Domiano542]

I have the same problem. I changed my transmission oil and nothing. Mine started switching gears as I was driving. Then just jumping everywhere. I read it might be the transmission solenoid. I bought one rebuild threw Amazon for 75$. Going to do this tomorrow hopefully. I’ll let you know how it goes.

[@valerieuribe1620]

What if I have a tcm and I rubb off some of the rubber coating . And has never been repaired can u still fix it and how in the world u fix it with all that rubber stuff stuck on the circuit board...

[@upfixauto]

Yes we fix it with that rubberized silicone in the back. If you attempted to remove it, its okay, as long as you did not damage the circuit board and board components.

[@iarebrianiare]

My Mazda 3 will drive fine but sometimes gives a kick and the AT light and engine light come on.but there are no codes stored making it difficult to diagnose the issue ,given the modus such a common fault do you think it will be a module fault?

[@upfixauto]

Yes, this is very common, and the TCM module is starting to fail. Here is more info www.upfix.com/product/tcm-mazda-3-2006-2014-transmission-control-module-repair-tcm-tcu/

[@husseinhamid5700]

Hello, how much will cost me to rebuild tcm for Mazda 5 2012 in Canadian $?

[@upfixauto]

Here is the link for current pricing www.upfix.com/product/tcm-mazda-5-2007-2015-transmission-control-module-repair-tcm-tcu/

[@ibmtpx24]

Why is Mazda 5 2015 not part of the affected model? 2012-2015 Mazda 5 are the same generation right?

[@upfixauto]

Yes the 2015 is affected as well www.upfix.com/product/tcm-mazda-5-2007-2015-transmission-control-module-repair-tcm-tcu/

[@MuttonChops24]

If i do the exchange program how quickly will i get the new part? I got a hot date next weekend and need my car running asap

[@upfixauto]

It usually takes about a few days before we ship you a good working exchange part, it also all depends on your part number. Some part numbers we have plenty in stock and can ship to you same day and other part numbers are harder to come around and we are constantly getting cores back and try to turn them as quickly as possible.

[@ryanmaratas9087]

where is the TCM location for 2009 mazda 3? I already checked under the battery tray but I couldn't see it

[@upfixauto]

If it is not under the battery, then your vehicle does not have a TCM

[@HuskerRed11]

Do you guys have a TCM for a 2008 Mazda 6? 2.3L, 5 speed automatic.

[@upfixauto]

No sorry

[@ConwayBarnett]

Hi, is the Mazda premacy Japanese and the Mazda 5 TCM compatible

[@upfixauto]

No they are not, this is one of the common questions that we get.

[@Wimba099]

Hi I have a problem with a Mazda 3 2006. The gear lights start blinking and the transmission works at a constant speed but if you put on gas it starts to jerk and feels faulty. I get no AT light on or any fault code. I am really lost here any help or suggestion will be highly appreciated.

[@245artist]

I would recommend getting it scanned with a good scan tool that way if there are hard faults an decent scanner should pick it up. 2006 was the first year of that body style. Some early Mazda 3 2006 units don't have a TCM especially if it's a 2.0L engine. If yours is a 2.3L, chances are you have a TCM that simply needs to be rebuilt if it wasn't done already.

[@upfixauto]

Great answer Ernest!

[@ManaBDew]

The ECM is inside the battery box 🗃️ ✅

[@JT2474]

Took my 2011 Mazda 3 to get a transmission rebuild because I noticed some issues with the transmission it was slipping and jumping and the AT light came on. I just got my car back not even a day and the AT light came on and when I put the car in reverse it started to jump. When I’m driving it doesn’t jump or slip. Do you have any ideas what could it be?

[@upfixauto]

Transmission that was rebuilt was original? If not, I’d check if the TCM is original or matches and if it has ever been rebuilt. If your light is on, then best to scan for codes will help pinpoint the issue.

[@JT2474]

No not original. The car was driving fine when I got it back but the rpm’s went crazy all of a sudden when I was barely going 20-25 mph and the AT light came on. I turned off the car i waited a few hours the AT light went away but I took the car for a drive again and the same thing happened again the rpm’s went crazy and the AT light came back on.

[@upfixauto]

RPM reving sounds like the gear is slipping. Either the replacement transmission has a bad TCM or the transmission had an issue during the install. On that year range Mazda 3 and Mazda 5, transmission is usually okay and problem with TCM. Very common issue for TCM to fail and make it seem like transmission is slipping. We do rebuild TCMs, here is more info: www.upfix.com/product/tcm-mazda-3-2006-2014-transmission-control-module-repair-tcm-tcu/

[@michealchanda9726]

Were is TCM for Mazda Demoi zj engine 2003?

[@upfixauto]

Should be under the battery

[@ambrosiotorres3387]

Only mazda from 2006 and over can be fixed. Have a 2004 mazda 3 with same problem.

[@josephlind5773]

Any chance you know how to fix/where to start with a p0791 code (intermediate shaft speed sensor) Recently replaced my TCM and now this code appears

[@upfixauto]

No sorry, not familiar with this code

[@jesusvargas4522]

Hi i have a cuestion sorry my name jesus my question is wen replacing tcm nee to be programed

[@kiwishbj1]

Sounds great. With the exchange program, what if your TCM doesn't fix the problem and I have not sent you my Core TCM... Can I get all my money back if i send back your Up-Fix TCM.??

[@upfixauto]

Yes, if there is still an issue after the replacement TCM is installed, you can send it back for refund minus the shipping amount. Please do proper diagnostic and see common issues that are associated with bad Mazda TCM: www.upfix.com/product/tcm-mazda-3-2006-2014-transmission-control-module-repair-tcm-tcu/

[@upfixauto]

Here are some of the common issues with bad Mazda 3 and Mazda 5 TCM units: -Hard Kick on Drive & Reverse -Hard Kick On Reverse -Hard Shift From 1st Gear to 2nd Gear Issue -Hard Shift From 3rd Gear to 4th Gear Issue -Hard Shifting Issue -Harsh Downshift Issue -Harsh Gear Shifts Issue -Intermittent speed sensor signals issue -Late shifting issue -Transmission not shifting issue -Check Engine & AT Lights Come On -DTC Code P0753 (Shift Solenoid A Malfunction) -DTC Code P0758 (Shift Solenoid B Malfunction) -DTC Code P0763 (Shift Solenoid C Malfunction) -DTC Codes U0101, U0100 (Lost communication with TCM) -Hard Kick On Drive -Vehicle stays in 3rd gear only (safe mode) -Error P0715 -Error P0720 -Error P0744 -Error P0745 -Error P0748 -Error P0768 -Error P0773 -Error P0778 -Error P0791 -Error P0841 -Error P0882 -Error P0883 -Error P0884 -Error P2709 -Error U0073 -Error P0772 -Error P0762

[@upfixauto]

Mazda 3 - Full List of TCM Common Issues: www.upfix.com/product/tcm-mazda-3-2006-2014-transmission-control-module-repair-tcm-tcu/

[@upfixauto]

Mazda 5 - Full List of TCM Common Issues: www.upfix.com/product/tcm-mazda-5-2007-2015-transmission-control-module-repair-tcm-tcu/

[@kiwishbj1]

I sent my TCM for fixing.. it's now 2 weeks. I was only contacted once that my product was an hold actually on the day it was supposed to have been completely fixed. After that I was given a 3 days of completion affirmation that it will be ready. 5 days later and I have heard nothing.

[@tvbenguisimao6908]

Hey upfix I just get new pcm but the light stil one not work what should do please

[@upfixauto]

If you got a new/used PCM. First make sure the part number of the replacement part is same as your original part number. Then you may need to have it additionally programmed. That can be done with a diagnostic scan tool.

[@ManaBDew]

Difficult to find too

[@IsrarKhan-zi9cc]

Hello, my 2013 mazda5 is been acting up for a while. Every once in a while, my transmission will shift gears for no reason a and i will get AT sign on my dash. Could u plz tell me what it is and how to fix it.

[@upfixauto]

I recommend going to read the codes with a diagnostic tool. Could very well be your Transmission Control Module as they are notorious for going out in your model of car. We can repair the control module if that is the issue.

[@DamionHardin-xn3js]

How long does it take to get a TCM back from you

[@upfixauto]

It usually takes 2-3 days for repair

[@thusomosaunyana5721]

Please help I have Mazda 3 LF4 engine last time it brings AT light,it refused to go beyond 40km/h I replace the gearbox filter and when I drive it suspended it moves fast What could be the problem that makes the gearbox to fail to move

[@upfixauto]

First, we would need to know the year of the vehicle. Depending on the year, we would know if the vehicle has a TCM or not and once the hard codes are provided, we can assist in troubleshooting further. The symptoms described means the car is currently in limp mode.

[@rubenrrodriguezsr4417]

We're is the tcm on a 2005 mazda3 2.3 hatchback?

[@upfixauto]

It is on top left (driver side) corner, under the battery. Here is the part removal video for a Mazda 3 kzbin.info/www/bejne/r5CyiXaLnpd2gbM

[@adzsness]

i have the problem with my mazda 3 2015 model , i dont know where the location of the tcm is

[@upfixauto]

It should be under the air filter box.

[@kiwishbj1]

I sent my TCM for fixing.. it's now 2 weeks. I was only contacted once that my product was an hold actually on the day it was supposed to have been completely fixed. After that I was given a 3 days of completion affirmation that it will be ready. 5 days later and I have heard nothing.

[@245artist]

Normally it's 1-2 business days turnaround. If there are any delays you should've received an email from UpFix stating if there was a hold on the order. I'd reach out to UpFix and find out if your issue wasn't resolved already.

[@kiwishbj1]

@@245artist After 10 days.. it was fixed.

[@upfixauto]

Sorry for delay we were experiencing an increasing demand on Mazda 3 TCM repairs and were hiring and training new techs for this repair.

[@kiwishbj1]

@@upfixauto THANK you UP-FIX. My TCM was installed back in to the car and it's working so well ever since. It's now 2 months gone since I have been using it.

[@victoranderson1264]

The delay for me has been even longer. I'm still hoping Upfix can come through.

[@rrltruckingllc2605]

How much is a new rebuild one

[@upfixauto]

Here is our TCM page on our web site. Let us know if you have any more questions, and Thank YOU! www.upfix.com/product-category/repair-return/tcm-repair/

[@kevinthomas1320]

Where can I buy a Tcm for my Mazda 6 2008 ??

[@upfixauto]

Here is a link www.upfix.com/product/mazda-3-2006-2014-tcm-transmission-control-module-exchange/

[@Josh-vp2iz]

Hey what if it has the same problems once I’ve replaced it?

[@upfixauto]

Well then that means, the problem was not with TCM and elsewhere. Please make sure to properly diagnose the issue and make sure problem is with TCM, before you send it in for repair. Dont send it for repair if your TCM is good.

[@Josh-vp2iz]

@@upfixauto am I able to email you guys? Or what would be the best way to contact you?

[@upfixauto]

Yes you can email, call or text us. Our website is upfix.com Email is [e-mail] Call/Text 1-888-979-9343 We are open Mon - Fri 9am to 5pm ET

[@raphaelarlequin]

@@upfixauto I sent mine for repair with the exchange option. Everything was better than before when I installed the TCM you guys sent me. After 3 days symptoms of rough downshifting, slipping and no reverse came back. What’s next 🤷🏼‍♂️🤦🏼‍♂️

[@upfixauto]

@@raphaelarlequin when you re-installed your TCM back in t your vehicle, did you mount it to brake lines or installed back on the transmission? If you installed it back on the transmission then it will overheat again eventually and fail. Also, what codes do you get? This will help to identify what issue you are having.

[@James.Gornell]

does anyone know if the 2014 Skyactive 6-speed automatic 2.0l suffer from this TCM issue?

[@upfixauto]

What codes are you getting?

[@GenesisZagal-pn5ep]

it's Mazda 5 2009 So I'm having a problem with my car so I start the car and put it into drive let go of the brake and step on the gas and instead of driving off it just rev when I step on the gas any Idea

[@upfixauto]

Would be good to know the codes first. Vehicle not moving at all when in drive is either faulty TCM, solenoid issue or something physical like transmission going out or not enough fluids. Sometimes when it’s that severe it’ll only go in reverse but not drive.

[@jasonranches8847]

I have this problem with my CX-9

[@245artist]

What codes are you getting and are there any phsyical symptoms?

[@jasonranches8847]

@@245artist when warmed up it shift hard in reverse and third . Sometimes it won't go in third or it gets stuck on 3rd and A/T light turns on. When the A/T Turns I pull over and turn off the car then turn back on and the A/T light goes away

[@245artist]

@@jasonranches8847 I'm curious to know what year your CX-9 is. They typically don't suffer from the notorious TCM failure like the Mazda 3 & 5. So either the transmission fluid and filter needs to be serviced and if possible, provide the specific codes the ECU/TCM is throwing off.

[@jasonranches8847]

@@245artist 2010

[@245artist]

@@jasonranches8847 Your TCM most likely just needs reprogramming which any local Mazda dealer should be able to do.

[@notiturismoonline]

can you send to Mexico? if you do, thetre is any tax if you send the tcm??

[@upfixauto]

No sorry we currently dont ship to Mexico, just to a USA address

[@jimsefulu4385]

Hii im looking kearbox of Mazda premacy 2008 please

[@upfixauto]

Yeah Premacy has same issue

[@myronleboeuf8969]

What site do I go to?

[@upfixauto]

UpFix.com

[@kuyaarnisvideos6632]

hi! how can i order a 2010 mazda 5 tcm from you? pls help im having problem on my car. thank you and godbless

[@upfixauto]

You can send yours for repair or get one ready to ship to you with a core fee: www.upfix.com/product/tcm-mazda-3-2006-2014-transmission-control-module-repair-tcm-tcu/

[@kuyaarnisvideos6632]

yes i would like to send my tcm for repair, and if i get one how can i make payment? thank you for your help and godbless

[@upfixauto]

@@kuyaarnisvideos6632 you can choose options on our website upfix.com

[@kuyaarnisvideos6632]

i cannot open your website

[@upfixauto]

@@kuyaarnisvideos6632 what country are you in?

[@karlapesina135]

I just replaced mine with y’all, and I paid $329.99 not $199 🤨

[@upfixauto]

Sorry the video was outdated. For current accurate pricing please see our website www.upfix.com/product/tcm-mazda-3-2006-2014-transmission-control-module-repair-tcm-tcu/

[@derrickforrester103]

My mazda 5 sticks in third speed and races before changing to the fourth and fifth speed than a AT light seen.

[@upfixauto]

kzbin.info/www/bejne/r5CyiXaLnpd2gbM

[@rafaelmeneses5066]

Great video but the music drowns out your voice.

[@upfixauto]

Hi Rafael! Thanks for letting us know. Also, thanks for watching and commenting, and please subscribe. If you ever have questions or suggestions, we'd love to help! - UpFix

[@joseordonez4654]

I have 2013 masda mx-5 miata with ctm problem code u0101 but can't find where is location if someone know please

[@upfixauto]

Here is a video that shows removal instructions kzbin.info/www/bejne/r5CyiXaLnpd2gbM

[@luizcermeno5411]

Hey question my 2010 mazda 3 2.5 my check engine light and the AT light came on my car won't go pass 3rd gear is that 3rd gear a safety for the transmission?

[@upfixauto]

Yes the TCM is failing and causing this issue.

[@luizcermeno5411]

@@upfixauto copy that thanks for the fast response 👏

[@kenrey7817]

Mazda 5 2.3 error code is p 0700 and a t light is on

[@upfixauto]

This is not a common code for a bad TCM unit

[@rays4067]

06 mazda 5 cams without tcm? now what

[@upfixauto]

Some Mazda 3s dont have them. It is built into a different module PCM/ECU

[@DanKirchner5150]

i gotta busta clusta ?

[@upfixauto]

Not sure what you said?

[@DanKirchner5150]

@@upfixauto THE CLUSTA

[@unclejun84]

Hey buddy I'm entrepreneur candidate, that looking for new business, can we talk private

[@rohncox7067]

Mazda axela

[@upfixauto]

As far as we know its for Mazda 3 and Mazda 5

[@myk3ch1chas196]

Hey I got p0600 U0101 in the engine ecu but in the TCM it's not code is my ECU the problem?

[@upfixauto]

Code U0101 is a common code for a bad failing TCM unit on Mazda 3 and Mazda 5. We are flooded with customers sending these parts in for repair with this issue.