Carter WO Carburetor Initial Adjustment And Checks G503 Willys MB CJ2a and Ford GPW, A1223

  Рет қаралды 33,956

Team G503

Team G503

Күн бұрын

Пікірлер: 41
@paulcornelljr5140
@paulcornelljr5140 16 сағат бұрын
Excellent video
@LetsBuildaWillysJeep
@LetsBuildaWillysJeep 3 жыл бұрын
G503 instructional videos are a great help with restoring a Willys Jeep!
@johns.earljr.3631
@johns.earljr.3631 Жыл бұрын
Just bought a new manufacture YO carburetor for my 46 Willys. Mounted it on the engine and fired it up. First thing I noticed was that gas was pouring out of the carburetor. Tried it a couple more times and decided to send it back to the supplier, which I did with his blessing. I have an original YO so I ordered a rebuild kit for $55.00. Not sure why it flooded like that but I didn't want to dig into it and maybe void a warranty.
@jimshaw7322
@jimshaw7322 3 жыл бұрын
Great Information, glad I found this Video before I tore my WO apart. THANKS
@Truffle1947
@Truffle1947 Жыл бұрын
Thanks Scott. Today I discovered my Jeeps old solex carb has developed a huge fuel leak so I will finally be pulling it off and fitting one of these JMP Carbs :D This video is really helpful.
@user-fp3gx2ow7p
@user-fp3gx2ow7p 3 жыл бұрын
Excellent Scott! By far the best WO video I have seen to date.
@johnbradshaw354
@johnbradshaw354 Жыл бұрын
Thanks Scott ,Great video. Keep um coming!
@gordonliddy9418
@gordonliddy9418 4 ай бұрын
Thanks for the vid. Helped with the setup of my grandpas 50 cj3a jeep.
@nschluter8709
@nschluter8709 Жыл бұрын
Love the video! Any update on when the carb tuning adjustment video will be released?
@danodamano2581
@danodamano2581 2 жыл бұрын
Lots of nice little parts that my fumble fingers can drop into the intake.
@danielausten3840
@danielausten3840 2 жыл бұрын
I took the carb off and made sure it was fine. A few weeks later, it just stopped. I had to choke it, but it idled. I replaced the fuel pump and now my jeep idles fine, but as soon as I push down on the accelerator, it revs a little bit and stalls out. Do you know what could be wrong?
@peerplaut
@peerplaut 2 жыл бұрын
Thanks for this video! I successfully, I hope, adjusted my carb!
@thebiggerman6975
@thebiggerman6975 3 жыл бұрын
Well I bought one of these carbs for my old cj2a I plow my dooryard with,It hasnt had brakes since 1988 so shes no show piece but I just wanted it running good to plow.It had the original carb and ran kinda rough so I thought it would cure her but it didnt,Its easy to blame the carb on a old vehicle,I wanted to but I didnt,come to find out my pcv valve innerds were missing and number 3 and four cylinders were getting a watered down dose of fuel ,I repaired that issue,Installed electronic ignition cause you cant get a decent condenser anymore and re installed the carb,I didnt monkey with it like in the video but instead chanced it,I can say on start up it ran like shit,little to no accel pump action but after about 15 minutes she came on line and has been fine since . my advice give it a little time to get that accel pump working and settle in before you get discouraged
@sabbasihota183
@sabbasihota183 Жыл бұрын
You guys are awesome 👌
@ginacoronel6872
@ginacoronel6872 3 жыл бұрын
A great video for sure, I've never seen the metering rod tool used before so that was great, also what camera do you use image quality was amazing!
@paulsworld07
@paulsworld07 Жыл бұрын
Scott. Where'd did you go?
@alphaalpha8270
@alphaalpha8270 2 жыл бұрын
Hi great job Plz show me how to fix seat belt for front seat in 1942 ford gpw jeep
@danielmarquess7860
@danielmarquess7860 4 ай бұрын
Do you have any videos of replacing the master cylinder
@leftcoast9261
@leftcoast9261 2 жыл бұрын
No gasket between the middle casting and the top one? Why is this?
@rgvfdengineer
@rgvfdengineer 3 жыл бұрын
Scott, I am doing a frame off on a 1947 CJ2A. I have been following alongs with your vidoes of the MB. Have you done a video on the installation of the transmission on the frame? I just viewed the rubber mount on the transmission crossover and you installing the engine videos. Saw you have the trans mounted on the frame.
@rickmaltz5632
@rickmaltz5632 3 жыл бұрын
Nice Scott
@TeamG503
@TeamG503 3 жыл бұрын
Thank you my friend 👍
@jeeperalainbigal
@jeeperalainbigal 2 жыл бұрын
Superbe video , merci !
@drdghattierdc
@drdghattierdc 2 жыл бұрын
I had a joes carb in a metal box. Thought I could take it and drop right on the gpw. No go. ran like crap when it ran at all. The video states the gauges are included Not so. waiting on gauges now to try and make this carb work. There really should be a note in the carb box stating this needs to be gauged before install. i have had carb for a WC from John Bizal at Midwest. Drop them on the truck and never touched it again. Just plain worked. This is a nice looking carb, perfect in every way, just not adjusted properly. At least there is a video on what to do.
@joe3973
@joe3973 10 ай бұрын
How do you clear fine particles in carburetor housing chambers that’s the most problematic.
@bobbyradford2711
@bobbyradford2711 3 жыл бұрын
From other videos I've seen, after setting the metering rod, the linkage should slide into the top and bottom levers without moving the them. If it doesnt then the linkage needs to be bent slighty so it hooks to the top and bottom levers with out moving the metering rod lever or the throttle lever. Is that correct, or am I missing something ? thanks
@joshbagley1959
@joshbagley1959 8 ай бұрын
Have you done the fine-tuning video for these Joe's Motor-pool Carter Carburetors?
@yvesderyckel4500
@yvesderyckel4500 2 жыл бұрын
Again a great video. Thanks Scott. BTW, how can we differentiate an original Carter from that very good replica?
@brucejones5341
@brucejones5341 Жыл бұрын
Show the final needle adjustments please.
@jfpooliovids
@jfpooliovids 3 жыл бұрын
Unless I'm missing something you want to set the metering rod with the linkage from the throttle connected. Setting it the way you did means that the metering rod is likely to be raised up and too high when you connect the linkage. Is there a reason to set the metering rod disconnected and fully lowered like you did?
@TeamG503
@TeamG503 3 жыл бұрын
Initial setting. The metering rod should be set with no tension on the idle screw. This is to check before you install on the engine. As stated in the video, this is a pre installation check. If the linkage is installed correctly, there will be no force from it until the accelerator pedal is depressed. We will get further into the adjustment process on the engine in the future👍
@jfpooliovids
@jfpooliovids 3 жыл бұрын
Oh, and thanks for the videos and parts! Really appreciate folks like you that are helping us keep our awesome jeeps rolling.
@TeamG503
@TeamG503 3 жыл бұрын
@@jfpooliovids I’m not expert, and learning everyday. Thank you for watching, and for your comments 👍 That’s how we all learn. Including myself.
@keithkohl6305
@keithkohl6305 3 жыл бұрын
So Joe in the Motorpool can't properly assemble and adjust their own simple one barrel carb? Maybe Joe would learn something if he watched your how to video. Can you recommed a brand of carb that does not have to be taken apart, properly adjusted and then reasembled by the user ?
@mbmpablo3631
@mbmpablo3631 3 жыл бұрын
So fuckin true!! $500 on a carburator is not ready to install !!
@keithkohl6305
@keithkohl6305 3 жыл бұрын
@@mbmpablo3631 crazzzy huh.. I remember when I was 12 I took apart a Rochester Quadrajet four-barrel carburetor. Rebuilt and adjusted it perfectly without anybody's help. Come on Joe's Motorpool it's a ONE Barrel Carb, how many of them do you have to improperly assemble before you accidently get one right
@celioazevedo4848
@celioazevedo4848 9 ай бұрын
Perfeito 👍
@frankporfidio9813
@frankporfidio9813 3 жыл бұрын
The very word carburetor is derived from the latin word "Leaveitthehellalone" .......LOLFactory should've done a better job installing that stuff though . Those are static settings and should've been done during assembly .
@billpayne3983
@billpayne3983 Жыл бұрын
Excellent. It doesn’t come much clearer and well produced than that. So many other carb rebuild demonstrations are badly lit, out of focus and have the camera so badly positioned that hands and arms obscure the action. Not that one. Thank you.
@Bob-tn5xn
@Bob-tn5xn Жыл бұрын
The crappy directions with all master rebuild kits show adjusting accelerator pump linkage with a tool that dosent come in joes kit and shouldnt that have a bearing on final metering rod linkage positing and adjustment !
@kirkpencil1791
@kirkpencil1791 3 жыл бұрын
👍
Can you tune a Willys jeep better than the factory?
18:38
Greendot 319
Рет қаралды 84 М.
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 30 МЛН
Honda GC160 Pressure Washer | Bad Oil Leak!
29:44
Tom Doby Mower Repair
Рет қаралды 736
Rebuild Carter WO Cj2A carburetor
27:35
Red Eye Cafe Garage
Рет қаралды 4,9 М.
TOP 5 Ways you are DESTROYING your WW2 jeep (without knowing!)
18:13
VINTAGE WILLYS: Trail Wheeling 70-Year-Old Flat Fender Jeeps | EP5
19:21
Nicole Johnson's Detour
Рет қаралды 457 М.
If you own a WW2 jeep....check this NOW!
15:11
Greendot 319
Рет қаралды 109 М.
Willys MB Carter WO Carburetor Installation G503
6:44
Team G503
Рет қаралды 35 М.
Willys Jeep How To: Carter Carburetor Rebuild Pt. 1
21:50
Kaiser Willys Auto Supply
Рет қаралды 7 М.
Willys Engine Heat Riser Problems, Problems, and A Fix !!
17:26
metalshaper
Рет қаралды 13 М.
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН