When you put the head back on verify valve/cam timing with a degree wheel and a dial indicator. CALL JBR or Drag Cartel and ask where you should set it. Valve lash not being properly adjusted is why those valves were black. I would check lash before and after the dyno just in case. This isn't a street engine. If that engine really had 2 miles on it and 5-6 pulls you have some valves that are bending or tuliping if lash wasn't set after the head was bolted on the second time. Verify your coolant temp sensor is reading properly with a temp gun and let the engine cool off between hits. It failed on the exhaust side, that tells you things are hot and moving around
@traviskridler886822 күн бұрын
Would the lash be too loose or to tight in this case?
@Jonny_trans21 күн бұрын
@traviskridler8868 A couple of things happen. If a valve is getting too too hot and tuliping, it's effectively pushing the stem further up. Losing(or tightening) any set lash. And possibly hanging the valve off the seat ever so slightly. It looked like only 1 valve per cylinder. There's a possibility the Lash wasn't set after the head was bolted on, and the distortion from those really fancy headstuds took lash away (not likely but not impossible)
@petedavis993523 күн бұрын
“Should be a nice and simple build” famous last words.. ha
@joelh336423 күн бұрын
nobody beats this daily content!!!!!! 👌👌🤘🤘💪💪💪
@LuisGonzalez-qv7xz23 күн бұрын
Great job! 👍
@jayhow99723 күн бұрын
What's the cold start set up like on those. is there coolant pipes running to the throttle body idle control valve that has a rubber gasket in kind of like the Subaru's. Very high boost could push past a failing seal into the coolant system through there and push coolant. Obviously not if that system has been removed or non existent on that car.
@SewellT9923 күн бұрын
I know your tools work great but I think you would love Milwaukee 3/8 stubby and the insider rachet, as a technician I use them daily and they are fantastic!
@Boostlee23 күн бұрын
Just went through this with a newly built ramey racing block, i also moved on with stainless steel wire and 625+ head studs. Those studs are torque to 100ft lbs in three equal steps.
@onyangogift923323 күн бұрын
i dont like how the rebuild episodes are short😭😭😭😭
@bmwpride23 күн бұрын
What engine stand catch pan are you using?
@professorlife161923 күн бұрын
The gun show, putting those guns to work🤭 also is the oil pump upgraded, meaning did Josh port the oil pump to prevent starvation past 8k?
@jedidiahmoloisi568020 күн бұрын
What are those copper O-ring for?
@SollessGarage23 күн бұрын
Gas ports on the pistons too
@OkayJayy_23 күн бұрын
I own a 04 accord and would love to get a rhd 90s Honda just for the experience 🔥🔥
@BaderBuiltRacing23 күн бұрын
1000whp here we come 🥳
@hondaboyz213-cj2og23 күн бұрын
HONDA BOYZ FOR LIFE 💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙💙
@Kyleb9423 күн бұрын
This has to be one of my dream builds. 😊I will own one one day only problem hear in the uk there all rusted out
@BuiltByBurt23 күн бұрын
You guys got all the bmw cars I want and we got all the Hondas In the world lol
@TheOriginalSpawn23 күн бұрын
Salute Hass💯
@RomarkySosa21 күн бұрын
Saludos desde república dominicana me gusta mucho tu contenido pero siempre son en inglés sube en español para yo aprender más de todo lo que ases
@karlsundbeck102823 күн бұрын
You should put that 1000hp in one of the nsx
@TheGlennpoland23 күн бұрын
Very cool
@stevendurbin900623 күн бұрын
🔥🔥🔥
@flint70723 күн бұрын
🔥 🔥 🔥
@rolandotillit286723 күн бұрын
Hondas torque to 22ft/lbs +180 degrees in 2 steps 270 degrees for new bolts. New that comes out to around 200ft/lbs.
@dominicmaguire955023 күн бұрын
Loose for boost is the honda way 🤘
@emansuela_real23 күн бұрын
Do you help others rebuild their engines?
@massacre223123 күн бұрын
2 liter heater!
@AS-fm6iw22 күн бұрын
Most dont understand how bad it also is to tighten head studs that tight. U will blow gasket every 10k or 5k miles depending on how you drive it
@kevinrios659123 күн бұрын
Finally 🫶🏼
@spoopdiewoopdie809223 күн бұрын
Soooo someone fill me in. I’m not familiar with k at all. Don’t most people want vtec what is the gain of the vtec killer cam beside permanently deactivating vtec ?
@4g63boost823 күн бұрын
It makes it always in v tec
@spoopdiewoopdie809222 күн бұрын
@@4g63boost8 gotcha appreciate it.
@adamarm2623 күн бұрын
Why aren’t you wearing your vasyn latex gloves
@Wigwam9323 күн бұрын
Isn’t it called a “Fire Ring” not an “O-ring”
@tonitakave977523 күн бұрын
Lessssssssssgo
@rolandotillit286723 күн бұрын
Aluminum con rods don't last.
@caponecashfunds23 күн бұрын
I remember the days when u dropped daily videos at 3pm est on the dot. U fell off so hard 😂🤣 jk
@Hoopers_s23 күн бұрын
Hey. His times have been way toooo random.
@pimpfolyfe31223 күн бұрын
Jbr sending out leaking motors?
@murymih23 күн бұрын
Sometimes the BMW rip video is playing in my mind subconsciously the way a good blockbuster replays in the mind.✌️✌️🇰🇪🇰🇪