Techniques Idea How to Paint a Wood Fence in less 5 Minutes

[@waitersluvhjy66]

I am sure it could be improved. Check out the plans on the Stodoys website.

[@ragandoil]

I have been spraying since leaving the military in 87 ... no hard and fast rules on how to spray ... you work out your own method .. good steady work rate ..good job

[@AlexKunstar]

You did an outstanding job! I've been painting for 20years, obviously not everything can be sprayed like this but when it can its a great feeling. Only thing I would have done is use a small extension (and maybe a swivel) on your gun, but that's just personal preference. A+ job buddy.

[@russellbarton7565]

he is using a professional sprayer that is syphon fed from the 5 gallon paint bucket. I have painted houses with these sprayers and they work very fast and efficient. they can be rented from home depot and other tool rental places. the problem is cleaning, you have to go through multiple stages of cleaning by syphoning water and or paint thinner through the hose and sprayer depending on what kind of paint or stain your using.

[@911alps]

Very useful thanks for sharing that.....I didn't realise all the prep time with the sprayer until your post - thanks

[@edisonorellana]

Ok

[@bestpeter78]

Cleaning is much raster than painting by roler

[@luckyvet]

So in other words, saving the time and expense of renting, cleaning, and returning the paint gun is probably trumped by staining it with a roller and a brush on a job this small. Amiright?

[@johnadlington8063]

Fernanda Valdes s

[@lazydadsgarage]

4 minutes spraying, 40 minutes cleaning up the machine haha. I just got my first sprayer and I'm looking forward to learning how to use it!

[@thehoneyflow]

I know! Me too..but I think I'd rather clean it :P

[@josecubas2001]

Can you read the title. Use you mind and the others

[@scooboy]

Obviously the guy checked he was doing no harm with the overspray. Great job man and I will be hiring a sprayer when it's time to do my fence and deck!!!

[@Pfr10001]

Looks like a nice job. You have the technique and the use of tools down.... On painting wooden fences in general - it is relatively forgiving as surfaces to be painted go. Two coats and it comes out fairly even - you don't have any apparent light spots, streaks, etc.... It probably took as long to tape off the hardware as it did to paint that section of fence. As long as there is no problem with small amount of overspray (a little on the grass, a little over the top) I'd say it's a good method.

[@josecubas2001]

+fourmileroad1 Remember the grass grows again, that any customer has problem. So you do not leave streaks or splashes have to use the correct pressure tip with the appropriate machine.

[@martingomez2611]

Good job Jose! Let the haters hate!

[@josecubas2001]

I do not like to be treated badly but! defend myself

[@77Avadon77]

Looks good, you're obviously going faster then most people would to show how fast it can be done. Most of the time your first coat is a mist coat and then you go back for full coverage. You can use a wider tip and get a broader angle with more volume as well. That way you get greater coverage in each pass. I'm using the widest tip they make in my graco when I paint my fence. I'm going through 4 gallons every 30-45 mins or so.

[@paragondave5638]

Looking good Jose. 2 coats with 2nd coat up and down should allow for good even coverage. Pretty much how I did it for several years. Roll out any overspray and you're good to go. When I prepped, I'd recycle card board under the fence where possible to keep the stain or paint off the grass. Nice work in 4 minutes.

[@josecubas2001]

+David Orosz Thanks at least you're one of many who see the meaning of what I'm trying to show. Good luck and that life of you deserve

[@lightwithin37]

very nice technique, May Allah give you a reward i will try :)

[@christopherwebb650]

Great Video Jose! I'm going to use your technique when I paint my fence. thank you!

[@josecubas2001]

+Christopher Webb Thanks you is pleasure help you. any question text me to my phone or call me

[@FernandoRodriguez-ds5ri]

Tip of the day, paint going with the grain of the pickets. Up and down. Never side to side. Good luck amigo.

[@josecubas2001]

Gracias por tu comentario, la diferencia aqui es el producto que se utiliza. Es diferente al que aplicas en una puerta interior o los gabinetes de la cocina. Por eso no se hace como tu piensas que se deberia hacer

[@331whf9]

Tip of the day....he did...on second coat...gringo juevon

[@alcidestapia8077]

Excusas, excusas. Nadie es brujo para saber del second hand. El paisa esta lejos de mostrar un trabajo profesional. Tambien te recomiendo que hagas tus videos en español, si alguien no lo entiende, con google translator estaran 100 veces mejor.

[@luckyvet]

@@331whf9 It's good we have gringo's who invented electricity, compressors, and paint guns to make the job easier for you advanced humans to complain about it on your internet, iphone from a heated/air conditioned house invented by another lowly gringo.

[@op2352]

which gringo invented electricity, compressors and paint guns?

[@johnnycash7803]

Good man actually cross hatched it. Left to right then up an down. That's how you know a finish sprayer from just a sprayer.

[@orlandoflores6037]

I wonder how it looked fully dry. Stain runs and sprays unevenly just like paint does. I saw a lot of uneven spraying. I guess when I do this I focus more on on even coats for a nice seamless finish. Back brushing helps too. Also, you should let the first coat cure for a while before applying the second. That helps too for an even finish.

[@josecubas2001]

Thanks for your comment but after so many years doing the same thing I do not think you want to teach me to do my job

[@orlandoflores6037]

jose cubas You’re right. I can’t teach you. Like the saying goes, you can’t teach an old dog new tricks. But when you post a “how to video”, don’t get pushy when someone gives you suggestions to up your game. That’s just hypocritical and counterproductive.

[@josecubas2001]

Remember my purpose is for other people to learn, as I do for others. I do not think I answered you in a bad way. good luck

[@tabithasmith9349]

Bare wood must be brushed in, you can spray but backbrush is needed. Any manufacturer, paint store, rep, or professional will say the same thing. The bucket will also say it on the application method. Backbrushing will push the product into the wood and also enhance the appearance and the longevity. Always spray with the grain never side to side.

[@josecubas2001]

Read the instructions before talk

[@mohawksteel2215]

you are hired Jose , thank you

[@davedg33]

should wear a mask man you breath it in

[@josecubas2001]

I know, but I forget to use it.Good Luck

[@SnowBunnyMan]

That's a quick way to get cancer, paco. ^_^

[@ankhmaathotep7913]

you are very funny...

[@STV-H4H]

Do you have suggestions about using a clear stain? I have a cedar fence that I built 5-6 years ago that I am just about ready to begin staining. Because it was aged and grey with several years without any protection I used a pressure washer and spent several days cleaning all the crud from years of weather off of it, and I want it to stay the bright yellow/orange of the natural cedar for a few years. I have used airless and air painting equipment, but it was 25+ years ago and I don't know what I might need to know when I go rent a machine. Are you using an airless? I hear what sounds like an air compressor in the background.

[@josecubas2001]

In wood fence we use Solid Color Stain for Fence or Semi Transparent Stain for Fence. That Fence Stain you Can't use in other Jobs Special for Door or similar. I Use gas sprayer

[@KiaRashan]

Great video! New subscriber. I’m spraying my fence today but I don’t have that professional sprayer. 😩 Hoping it looks as good as yours!

[@josecubas2001]

That is easy. just be careful if it's windy

[@Jesse-hw7cd]

I like that the hinges match the fence👌👌

[@josecubas2001]

I'm sorry is taped

[@julienriegel8246]

I appreciate your technique brother, I'll try it in a minute. thanks hombre

[@josecubas2001]

Good Luck . Just Remember text me or email for any question

[@4jacquelines]

2 coats Good job ( I would like the spray then a coat on with a brush to last longer, I 🤔

[@andrewdavies1312]

Do you charge extra for painting the hinges walls and grass?

[@josecubas2001]

Use you brain if you have. What you think the other painters do it

[@andrewdavies1312]

@@josecubas2001 I have painted fences. I don't spray hinges I tape them off.

[@josecubas2001]

I thought you were smarter than those who speak stupid. watch the video well and learn. There you will find your answer

[@labonitapz]

Jose te va a dañar el hígado de tantos corajes que haces......take it easy bro!!!!

[@praise2day]

It looks pretty good. What type of paint and color did you use?

[@josecubas2001]

you can find the color in home depot the paint too

[@stusmith83]

jose you're a boss!!! fast good job

[@josecubas2001]

+stu smith Thanks any question I'm Here To Help You

[@cesarortega2671]

Great job Jose ... I’m a painter as well and I usually do a coat of primer so it won’t suck the paint, what it’s your opinion on that ?

[@josecubas2001]

I'll tell no need apply primer to wood fence, just two coats of paint; remember that it is a special product that does not need it. Este producto lo puedes aplicar directo. (WOOD FENCE STAIN).

[@stevemcqueen3878]

great job you did not just paint the fence you painted the neighbor's trees the neighbor's car and God knows what else fantastic job

[@josecubas2001]

because you do not use your head and think a bit, not only to have the hair used, do not talk what you do not know

[@tonyoliveira4786]

How did I get here

[@brianholloway1267]

Tony Oliveira

[@prithvimann1539]

Same

[@ss_whole]

...and you may ask yourself "How did I get here", and you may ask yourself, "Am I right? Am I wrong?" And you may say to yourself, "My God! What have I done?"

[@G0dspelronin]

@@ss_whole Letting the days go by, let the water hold me down...

[@toneroable]

Jose..una pregunta.............. es el mismo tiempo...con el STAIN..??????

[@josecubas2001]

Aqui estoy pintando con wood stain para cercas solid color

[@josecubas2001]

Aqui no se deberia aplicar otro tipo de stain si es a ese q te refieres, como el que se usa en puertas

[@josecubas2001]

Veo que te gusta cantar, Felicidades el sentimento lo llevas dentro.

[@sergeantc4073]

Nice 👍

[@yesikamatute9043]

You are the best!

[@usooalo3b09]

Nice Job👍🏽👍🏽👍🏽👍🏽

[@mrsoulivue]

Looks great my friend!😀

[@cameras5824]

Yes! Fast!!! Very good!!

[@stephiec2763]

How do you keep the paint from going through the cracks between the boards to the neighbors side? I've been wanting to paint my fence with a sprayer because it looks like it saves so much time but I just don't want to have any issues with my neighbors. Thanks 🙂.

[@josecubas2001]

Thanks for your question. 1. First you can't do it when it is very windy. 2. The paint that crosses the cracks is very little. 3. If your neighbor has something near or near the fence you can use a cardboard which you can buy it or it would be better to use a painter drop cloth (this is what we use sometimes),

[@josecubas2001]

Good Luck

[@johnsomerset1510]

Great, but what sprayer and paint did you use?

[@josecubas2001]

Graco 5900 gas sprayer . Paint you can find paint store

[@johnsomerset1510]

Thanks

[@thelandballin747]

@@josecubas2001 Man that's a $5,000 sprayer. No wonder my $250.00 graco airless doesn't work as good.

[@josecubas2001]

But you sprayer is good.

[@virgiliogarcia2105]

Eh jose una pregunta sepuede pintar fens d metal con eso y sisepuede q numero d boquia seria lo adecuado

[@josecubas2001]

No puedes usar ese producto, tienes que usar DTM WATER BASE. comprala en sherwin williams. Tip del verde number 308

[@josecubas2001]

O algo mas barato pero bueno seria all surfaces enamel water base.

[@Pinyoo81]

There might be some tutorials out there "how to build a straight fence"! :) Nice and quick paint job tho...

[@josecubas2001]

I not Build, just painting. Anyway thanks

[@dennismadigan2023]

I think you did good. What color is that? What is it stain or paint? What brand?

[@josecubas2001]

Im sorry about the color name or number, the paint and color you can find in home depot

[@rubenluque6032]

Que máquina marca y modelo usaste en el video , gracias.

[@josecubas2001]

graco 5900

[@capitanamerica4562]

What size a tip you used for stain? I have airless x7 paint sprayer Great job

[@josecubas2001]

I try use 411 sometimes 308. Depending if weather windi

[@josecubas2001]

That depends on the wind,

[@Vtard1]

I like to paint with brush....big board right hand 🤚, small board left hand 🤚. Bend your knees and ALWAYS LOOK EYE!!!

[@PeteS-cl3ny]

This guy has skillz

[@jonathanmarin6123]

can you use a stain product through a paint sprayer or will the product mess up the machine?

[@josecubas2001]

+jonathan marin Not really, it would be best to use a brush and a rag to remove excess

[@josecubas2001]

+jonathan marin to paint wood fences or wooden houses if you can use a machine to spray, because these products are like paint

[@LOREMIG]

oye nose una pregunta pinte mi gasibo con stain y puso un clear protector a la madera por lo del agua y polvi ademas esta cerca.de una alberca pero ahora noto despues de 4 semanas manchas como de agua manchas blancas si lo tallo con la una se cae pero ralla la pintura que puedo hacer para quitarlas o desaserme de este problema .... muchas gracias

[@josecubas2001]

Pintastes con el producto correcto.? Mira en un gazebo no se deberia usar el stain que utilizas para una puerta. dos cosas muy diferentes donde se usan productos diferentes tambien.

[@LOREMIG]

Se puede o no se puede usar lacquer sobre stain basado en aceite ... hace tiempo te pedi un consejo sobre un problema. Q tuve con mi gazebo me gustaria mandarte una fotos para que veas lo que paso y como me gustaria que quedara por q quiero repararlo ... tienes email? Gracias

[@pballer2005]

how is the overspray between the boards? I plan on sprayingmy fence but I'm worried about spray getting between the boards into my neighbors yard

[@josecubas2001]

+pballer2005 In our experience we take several factors: 1. Wind speed. 2. Separation of each piece of wood 3. Distance of what you have to protect your neighbor. 4. If this does not help you, the most important thing is to use a painters drop cloth , gradually moving over your neighbor's fence.

[@ajm9238]

Great job man!!!

[@miamiflow5701]

up and Down paint along the grain not across you'll get a more sequenced finish

[@josecubas2001]

Different products different techniques if want I think learning best for you

[@johnykash6856]

Jose es un vacano. Tremendo

[@castillofishing5483]

Good job🙂🤙

[@robgp6987]

Looks like you know what your doing sir.

[@nurseguy7581]

Jose what kind of sprayer and what did you use to run it? I have an air compressor what more do I need. thanks

[@josecubas2001]

+nurseguy7581 Now you have what you need.

[@josecubas2001]

+nurseguy7581 the best way to painting a wood fence and the best quality is using a spray machine,(compressor is fine)

[@antoniorivera1311]

Que pintura usastes?

[@josecubas2001]

Creo que a1ui fue wood scapes

[@halverdog4146]

What about back brushing the paint? Needed?

[@tamikabrooks7606]

great job I would be doing the same thing to my fence and the paint is green label good to know like I said be fore great job

[@josecubas2001]

+Mika Moore Thank you very much for your comentario.espero that my video will help a little. Glad you have initiative to do so. Any questions call me or send me a text message,. a pleasure to help

[@AB-jp9jb]

The compressor is crying .. What size is the compressor you using

[@josecubas2001]

5900 graco

[@Carolyn1952Hoxton]

Wow, I don't have a sprayer, would have to use a paint brush, impressive!

[@josecubas2001]

+Carolyn Hoxton Thank you, hopefully I can help a bit, so will give you an idea of how to do it. Good luck

[@christopherwilcox9654]

1. No overspray protection. 2. No mask. 3. No backbrushing.

[@josecubas2001]

Nothing is perfect

[@josecubas2001]

Whg you not try learning first, before open you mouth. Back brush. That is not a door. Ha ha

[@sammyrios8356]

Jose how much you charge the ft ? with material or with out material?

[@josecubas2001]

$0.70 to $1.20 Material Included. If the fence is over 2000 sf $0.70, less 1000 sf $1.2/ Note: 20 cents less with out material

[@911alps]

What spray gun and generator are you using ? How much would you charge for that job then for those panels you painted in your video ??

[@josecubas2001]

+Alps P Graco 5900 gas machine, that Job is $200 not less

[@josecubas2001]

+Alps P The machine I'm using is a gas graco 5900 machine, the gun comes with the machine. I did that job for $ 200, since we painted the house also

[@911alps]

+jose cubas thanks so are u using that with an air compressor or is it airless - I'm the uk and looking to buy a decent paint sprayer

[@redorangeuk]

+Alps P I am in the UK too - which paint sprayer you did up with? I have 22 x 3m fence panels to do, both side, so I'm looking for something that can help me there, instead of using a brush...

[@highway855]

Thumbs up for your badass accent

[@josecubas2001]

My proposal is help anyone, if you can learning a little is enough. You not think

[@dozermendoza]

What system is being used for spraying?

[@josecubas2001]

Could you ask your question better

[@dozermendoza]

jose cubas what type of spray gun are you using for painting? What brand of spray gun are you using?

[@josecubas2001]

graco 5900 gas machine

[@MrHuggys]

How much paint did you use?

[@josecubas2001]

150 square feet for gallon , sometimes depending the color

[@krazytrinisteve]

Looks beautiful, hire him I would but I am in va

[@zacharya.bradley8592]

Looks like good quality work to me. Well done sir.

[@josecubas2001]

+TankOfSpades85 Im here to help you

[@marinoldus]

Well done.

[@MrRyan0608]

sorry mi amigo. but when you cut the edges, its not necessary spray to high. i believe you painted the backyard also. next time use a bigger tip like 517 or 515. in your case will need at least one more coat. Thanks for the video.

[@duartepaintinghandymanservices]

MrRyan0608 those 2 tip size are good when theres no cars around or doing a big job, the size tip his using looks fine but he needs to learn how to control his overspray

[@DanOne1513]

Juan Navarro ...correct!

[@Djzpiky]

Amigo, apuesto a que después de pintar llegas a tu casa y tienes "toz" es porque no usas máscara y ese dolor en la garganta es por lo mismo. Es un consejo de PINTOR a PINTOR 👍🏼 saludos desde Hidalgo, México. Y a todos mis compás en Atl. Ga. ✌🏼

[@josecubas2001]

Gracias pero no casi nunca me duele la garganta

[@labonitapz]

Jose. Eres cubano?

[@ramonramon9185]

Saludos desde Oklahoma City me puedes decir a como cobrar te lo agradecería muchísimo hermano fíjate que acá no se mira ese trabajo estaría bueno para comenzarlo

[@josecubas2001]

$1 el pie cuadrado con material, recuerda que eso es por una sola cara si lo pintan por ambas caras seria doble, suerte ojala te ayude. Tambien puedes usar mi cuenta de home depot or sherwin williams. Solo text me 7869757597

[@ramonramon9185]

jose cubas mi nombre es Ramón hermano muchísimas gracias por tu Respuesta sigue adelante y mucha suerte y dios te ayude seguiré viendo tus videos échale ganas saludos desde Oklahoma City

[@josecubas2001]

Saludes que Dios llene tu vida de abundancia y sobre todo felicidad Salud.

[@omartorres1615]

@@josecubas2001 que onda raza como estamos aqui nosotros chingandole en la pintura te puedo llamar para a ver si me ayudas con algunos consejos sobre pintura?

[@rafaelmeza376]

the stain it's a solid color right

[@josecubas2001]

yes

[@salsan8896]

jose , muy bien tu trabajo solo que veo que no te pusiste protector o cubreboca,que opinas de las airless sprayer machine from harbor freight?.

[@josecubas2001]

Gracias, no conosco esas maquinas pero lo barato nunca sirve. Suerte

[@salsan8896]

si muy cierto,lo barato sale caro,que maquina me recomendarias, es solo para usarla eventualmente, no soy profesional en la pintura ni me dedico a eso,quiero algo no muy profesional,gracias.

[@josecubas2001]

No tengo idea de como sean esas maquinas, compra una maquina buena lo barato no te durara

[@salsan8896]

como que marca y que modelo

[@salsan8896]

como que marca y modelo

[@mijit.859]

Good job !! Excellent!!

[@josecubas2001]

Thanks

[@mijit.859]

+jose cubas 👍

[@spencercooper-thorn2624]

Why did you paint the gate brackets - shoddy oddy

[@josecubas2001]

If you see the video well, you will notice that they are covered. Thanks and good luck

[@everardotorres4688]

Jose from Miami south painting 1st of all protect your self from breathing all these paint chemicals 2nd of all cover the customers grass and use a blower to take all the leaves and grass away from the fence!!!

[@josecubas2001]

Thank you for your comment, You know the first thing that customers tell me, Jose, forget about the grass that grows. You do not believe it

[@pjpaps7687]

good job

[@logex2785]

He makes it look so easy

[@josecubas2001]

It's easy when you do the right thing

[@renatorossi3593]

Great job

[@josecubas2001]

Thank you, my purpose to give them ideas on how to do some work

[@chrisc.c52]

I'm a professional painter and what I can tell you about this video is: This is a perfect example of a painter that doesn't have pride in his work, he's just there to get fast money by cutting corners and finishing as fast as he can. When you don't back brush the stain after spraying it, it won't penetrate as it should and it's not going to last as long. You also have to let the first coat dry a little bit before applying the second coat. You can ask anyone that works in a paint store and they are going to tell you the same thing as me. Of course is going to look nice in the beginning and the homeowner is going to be happy that it was done fast, but when that stain starts to fade by next summer, he's not going to be as happy. By spraying it that fast without back brushing, the homeowner is going to have to pay again to have it restain way sooner. I might be slower in doing my work, but I guarantee my work and take pride in my work. Don't like cutting corners and taking advantage of my clients. Just be careful who you hire, and have him explained in detail, what steps his going to take, and if something doesn't feel right, you can always ask for a second opinion. Most contractors give free estimates, so you don't have anything to lose by getting more than 1 estimate. Everybody has their own opinion and this is mine.

[@fudgedogbannana]

2 coats in 4 minutes ay? No prep, no covering up anything, you don't use a shield over the top of the fence? YOUR FIRED ! …ok, ok I know you covered the hinges and the fence next to the wood, I only meant that prep is everything, painting is easy.

[@josecubas2001]

+fudgedog That is the problem that many people think that painting is easy. You know that there are many people looking for other painters to repair damage from what others painted, these were told painting is easy.

[@JodBronson]

+fudgedog 100% correct !!! TRASHY PAINTER HE IS !!! Painting is EASY... People are just lazy... It's NOT they can't do it, they are just lazy !!! But in the end he's a "TRASHY PAINTER "

[@STV-H4H]

I remember when I first began painting. I remember thinking it was 'easy'. I remember my boss the first time telling me I was an idiot and I thought he was a dick. But when I finally shut my mouth and opened my eyes, and realized he was correct and I didn't know shit. Painting isn't 'hard', but it's a skill that is more difficult to learn than it appears.My first job painting was using airless equipment, and the 'stop' at the end of every stroke isn't visible to the person watching, and it's not 'easy' to master. Doing a fence like this isn't something I've ever done, so I'm studying various videos to see different painters and their techniques.My later jobs working as a painter, I again thought 'painting is easy' when the new boss again told me I was an idiot, I again thought he too was a dick. But again, I came to understand that it wasn't 'easy' and he was correct in telling me to shut my fucking mouth and just pay attention, because rolling a wall and not having lines and drips and other mistakes is REALLY DIFFICULT until you actually know WTF you're doing, and doing it consistently.Thanks for your video. It demonstrates the speed that I knew was possible to spray my fence. Another video I watched earlier today was so slooooooooowwwww I was thinking I might not be willing to take the time to DIY after all.

[@dakotaforrester1406]

SamytheGreek Couldn't have worded it any better. I ALWAYS tell people this. Painting is easy, but the prep? Sheesh

[@duartepaintinghandymanservices]

z3dsdead your first job painting was spraying? you skipped many years of training, your first job should have been prepping, like sanding, patching, caulking. second job should have been using a roller than using a brush and after you master those you move up to spraying. I hope you went back and learn the basics, because the basics is what makes a painter. spraying is nice but is not something you would do daily. prep roller and brush is a everyday thing and without the proper prep the job wont come out right.

[@Wilson19604]

your neighbor must love you.

[@josecubas2001]

Happy you, your house in the jungle. With no one around, where nothing you do annoys your neighbor. Something as simple as cutting the grass, painting your house or washing your car. Nothing in this world is perfect. Those who want perfection are making trips to space.

[@allenpatterson329]

Good Job Jose!

[@josecubas2001]

Thank you very much. Hope it helps you, that's my purpose.

[@danielarnone7734]

Good work on the paint job. Keep up the good work.

[@josecubas2001]

Thanks

[@LOREMIG]

que clase de pintura es esa que color es?

[@josecubas2001]

Disculpa hasta ahora pude ver su mensaje. La verdad no lo recuerdo. pero este color es de home depot

[@josecubas2001]

Wood Stain para cercas vale como $37 el galon

[@LOREMIG]

Ok gracias

[@LOREMIG]

Una ultima pregunta si uso clear wood sealer para mi gazebo este tipo de productos no afentan en nada el color que tenga ?

[@josecubas2001]

no le afecta.

[@dagr8ape]

Great job Jose! I will call you for an estimate.

[@josecubas2001]

cuando quiera

[@jofloresz]

Fast efficient and great job great video thank you for sharing!!

[@josecubas2001]

thanks. good luck

[@Cleveland_Chris]

what size compressor please?

[@josecubas2001]

+Chris Zano I use graco gas 5900

[@BABYITSLIGGS]

can you please give me a link to the paint you used?

[@josecubas2001]

You have two types of stain applied to your wooden fence: 1. solid color is used in new and old fences. (Weatherproofing Wood Stain Solid Color) 2. color semi-transparent I recommend it only for new fences. (Semi-Transparent Weatherproofing Wood Stain) This color was bought at Home Depot

[@BABYITSLIGGS]

do you remember the brand of it by chance?

[@josecubas2001]

Behar

[@josecubas2001]

$36 something

[@josecubas2001]

Where you live

[@pataustin3686]

Great job my friend, is that a Greco contractor spray gun, love to see that no fuss no just good fast clean work

[@josecubas2001]

Friend, I wish you well

[@floridacruisers7705]

I would have covered the hinges.Now the paint will crack when opening.

[@erchep]

He already did. He also mentioned it.

[@digd6592]

Friday afternoon job and knock????

[@mariagarza2140]

Beatiful good job 👏 👍

[@VgniK88]

Yep clean ups the pits

[@4everdatingcomJohnCaruso]

what kind of paint gun do you use buddy?

[@josecubas2001]

Contractor spray gun . you can buy in paint store

[@allbeit222]

It's called an Airless Spraygun

[@duartepaintinghandymanservices]

allbeit222 no its called a contractors paint gun. Jose answered the question correctly.

[@benmuise2262]

I think the person the builder hired to paint our fence used this technique, but the results were very poor. The top and bottom still look good, but the middle part looks thin and you can see the spray pattern. It's not even. Do you think that they just rushed through it?

[@bruno-pierregirard5220]

Ben Smith is it a solid stain or a translucide one?

[@josecubas2001]

+Bruno-Pierre Girard solid stain you can buy in home depot.

[@bruno-pierregirard5220]

If u can see the spray pattern it means that there's not enough applied stain on the wood ...solid stain should cover all the surfaces evenly ... Probably needs another coat

[@josecubas2001]

+Bruno-Pierre Girard Anything you want painting need two coats for better quality and better result.

[@benmuise2262]

+jose cubas Thank you both. I've talked to the builder and he's having someone come out and redo it...twice.

[@duartepaintinghandymanservices]

this aint a 5min paint job, you have to account the time it took him to get setup. tape up the hinges, paper cover the wall on the left, setup the paint sprayer and finally start spraying, by the time you finish you spent around 30 to 40min setting up. you did ok with the spraying but I think you need to learn on controlling your overspray.

[@joedejesus6363]

Great Stain job, and a awesome technique thanks. Was that the Mahogany color you were using? But, ....I see you missed a spot. Just joking :-) I'll pass this video on.

[@erezr1234]

nice very nice :)

[@acheronlv-4268]

te la comiste consorte. tu si pinta bien!

[@josecubas2001]

+Alex Glez Gracias Hermano,Hay que aprender bien y jugarsela

[@Noaxe_Tegrinde]

Well done Jose.... I bet you don't need to go to the gym at night!!! I don't think that this method will work for me as I want a red fence.

[@josecubas2001]

Do not believe, it's sun that we take daily is not easy.