Watch [NEW] video on Fully Automatic Pump controller: kzbin.info/www/bejne/mJikg6SlqLBqipY
@karanmadavi732 Жыл бұрын
Pls do not connect 220v AC current if u are using 5v pump. I tried this and my 2 pumps are blasted. So i connect 9v battery supply instead of 220v and guess what! It works 👍.
@diplomatic71379 ай бұрын
So if I want to use it with a 220v power supply, can I use it with a 220v pump?
@adnansikandar23323 жыл бұрын
The common, pump ON and Pump off wires will get oxidation after some time due to electrolysis process.
@chanrashekharmirajkar10973 жыл бұрын
Use float magnetic sensor.
@vijaypaluskar8793 жыл бұрын
Thank you for such a nice home remedy "do it your self tech project" .Your presentation is very good. I want to add one observation to this effort. Generally you will find that water is pumped from ground floor water tank to the overhead water tank. The gadget you have explained will serve good purpose for overhead water tank. However a person need s to ensure that there is sufficient water level in the ground water tank. If that is not ensured the pump may have a dry run for a long time till the ground water tank gets filled with the water. This is a dangerous situation since motor may burn. Plz consider to add another water level sensor for the ground floor water tank. The pump should operate only if there is sufficient water level in the ground tank. Secondly if the electricity suddenly goes when the pump is running the pump switch must become off automatically inspite of the water level sensors giving signal to start the pump switch. Else when the electricity resumes pump may suddenly become ON again. Thirdly there should be an isolation switch for this automatic level controller unit, This will be needed when there is leakage of water in the water circuit and needing a repair . This will be leading to hunting of the pump On/OFF condition till repair is done and may not get noticed easily.
@TechStudyCell3 жыл бұрын
Thank you for your detailed feedback. Will do the changes in upcoming projects.
@bappaelectric3052 жыл бұрын
Bro 1 question answer please, isme components me 1k, 22 k, 180k,1m, sub 0.25w compalsary hai kya 1/4 w nhi chalega kya or, 2 question answer please, me isme 6v ka relay use kar raha hu ku problem tho nhi hoga na, resistance ka velue change kar na padega kya , capacitor ka bhi bolo,
@turiyathe4th Жыл бұрын
That pcb is a thing of beauty
@vasantakolkar33973 жыл бұрын
As you are using DC current in the probe immersed in the water, it will start electrolysis and corrode the probe material ( even S. S.) and the wire connected to it. Use ac voltage for the probe. Needs a better ckt. Good work. Instead of using + ve for common probe, better use ground.
@shant-o2 жыл бұрын
I was looking for this comment... Apparently nobody else said anything about it 🙄 I've changed the wire twice in 1 week 😂 still corrosion is going on
@krisp3629 Жыл бұрын
We just need it for a science project for a day, will it corrode?
@vasantakolkar3397 Жыл бұрын
@@krisp3629 no problem if used for on day.
@vasantakolkar3397 Жыл бұрын
@@krisp3629 no problem if used for one day.
@krisp3629 Жыл бұрын
@@vasantakolkar3397 thank you so much. Another question, will the circuit not work if I use a different capacitor and resistors?
@SanjayKumar-mz3wx2 жыл бұрын
बहुत सरलता से समझाया आपने, धन्यवाद |
@arumkumarbhattacharya77733 жыл бұрын
I'm a hobbyist, and this video attracts me. Now I want to make this project. Where I can get all the components (without the 230v pump) in on one package, can you help?
@wasiljaved46003 жыл бұрын
Sir good job, i have question that the supply in for pump is for what purpose if you have already given the supply to the pump?
@sathyamurthyponniah1242 жыл бұрын
@wasil Javed please note that only the neutral is connected to the pump. The phase will be connected after the relay switches ON ! If you wish , you could employ a Double Pole Solenoid/Relay instead of the single pole solenoid.
@simranmoraes32602 ай бұрын
It’s working very fine I liked but can you do other way around motor stays off and when reaches high it turns on and off when reaches low point please 🙏
@قناةإخترع-ش7نАй бұрын
Peace be upon you and God’s mercy and blessings. Thank you for your wonderful ideas. I tried this circuit, but there is a problem. The green lamp and the relay work, but when I touch one of the capacitor wires, it does not work when I press the button, nor does it work when I press the mount control. There is a problem, which is the reason for asking the question: Why does the infrared receiver component heat up?
@veeem3964 Жыл бұрын
Very nice design circuit, tried it and it works fine like in your video The only problem is the common probe (sensor) starts getting corroded over night , if the sensors in some way is AC volts this electrolysis won’t happen, please design Thanks for the video
@liamstone3437 Жыл бұрын
This looks like a useful circuit to keep a tank topped off but how about a circuit that pumps water out and shuts off when it reaches a certain level? I would use such a circuit for a 12V 20A bilge pump. I would love to see your version and when I make my bilge system I could link to your tutorial in my own video.
@azamchishty6129 Жыл бұрын
Did you make one?
@liamstone3437 Жыл бұрын
@@azamchishty6129 not yet. Still working on it
@prakashraje90513 жыл бұрын
Thanks boss. Muze nahi lagta isase behatar koi technic hoga banane ka. Kam like dekhkar dukh hota hai. Koi bat nahi.👍
@TechStudyCell3 жыл бұрын
Welcome
@A.S.khojaryavrat7 ай бұрын
सुन्दर है भाई साहब जी सर्किट
@simeonerasmus2 жыл бұрын
First off, great video thank you. Secondly, hiw can i change this so the pump turns off when the water level meets the middle wire and turns on when the water meets the top?
@jamesmyrthong61123 жыл бұрын
Superb video And also the background music. Thank You tech study cell.
@TechStudyCell3 жыл бұрын
Welcome
@bappaelectric3052 жыл бұрын
Bro 1 question answer please, isme components me 1k, 22 k, 180k,1m, sub 0.25w compalsary hai kya 1/4 w nhi chalega kya or, 2 question answer please, me isme 6v ka relay use kar raha hu ku problem tho nhi hoga na, resistance ka velue change kar na padega kya , capacitor ka bhi bolo,
@sidtube123 жыл бұрын
Great! I love this project. Thanks,
@TechStudyCell3 жыл бұрын
Welcome
@BalintNandori3 жыл бұрын
@@TechStudyCell can I also use this circuit for draining water? If I can i just have to use the normally closed "nc" pin of the relay?
@bappaelectric3052 жыл бұрын
Bro 1 question answer please, isme components me 1k, 22 k, 180k,1m, sub 0.25w compalsary hai kya 1/4 w nhi chalega kya or, 2 question answer please, me isme 6v ka relay use kar raha hu ku problem tho nhi hoga na, resistance ka velue change kar na padega kya , capacitor ka bhi bolo,
@repaircityhub7373 жыл бұрын
how can I add a circuit that will send a live feed back of the water level to my phone
@TechStudyCell3 жыл бұрын
Will make video on it.
@repaircityhub7373 жыл бұрын
@@TechStudyCell nice
@konghwathai89943 жыл бұрын
Excellence mantor.
@karunakaranrajakannu33463 жыл бұрын
This will use only for user Store tank what about main Storage tank and also dry run pump protector we need it
@anandjoshi8554 Жыл бұрын
use a nc float switch at under ground water tank ...connected in between power supply to the circuit.
@bhagvanthbhosle29842 жыл бұрын
Sir e jo last me pump ko supply de rahe ho e AC hai kya DC hai pls batao hamare clg hum isipar mini project bana rahe hai
@amrittimilsina70993 жыл бұрын
Can we use 220v motor here ?
@TechStudyCell3 жыл бұрын
Yes. But use the relay as per the current rating of the motor.
@amrittimilsina70993 жыл бұрын
@@TechStudyCell I have 1 Hp motor , which relay I should use please reply
@josedemiranda44452 жыл бұрын
où peut-on imprimer le schéma électrique pour le controleur de pompe
@bappaelectric3052 жыл бұрын
Bro 1 question answer please, isme components me 1k, 22 k, 180k,1m, sub 0.25w compalsary hai kya 1/4 w nhi chalega kya or, 2 question answer please, me isme 6v ka relay use kar raha hu ku problem tho nhi hoga na, resistance ka velue change kar na padega kya , capacitor ka bhi bolo,
@philipabraham74743 жыл бұрын
A honest and clear demonstration thanks good job best regards
@TechStudyCell3 жыл бұрын
You are welcome
@bappaelectric3052 жыл бұрын
Bro 1 question answer please, isme components me 1k, 22 k, 180k,1m, sub 0.25w compalsary hai kya 1/4 w nhi chalega kya or, 2 question answer please, me isme 6v ka relay use kar raha hu ku problem tho nhi hoga na, resistance ka velue change kar na padega kya , capacitor ka bhi bolo,
@mr.bhadauriya20036 ай бұрын
Sir please contact Krna ha aap se
@mr.bhadauriya20036 ай бұрын
Please sir please 🥺
@darrendarren92115 күн бұрын
can i use a solar to the source of energy?
@UbaidKhan-zt5bd Жыл бұрын
Can we use house pump instead of this
@youknowme67803 жыл бұрын
Great work around, how about auto on/off switch for exhaust fan after every 30 min circuit with 220V for fan? any suggestions
@GOPALJHAlife3 жыл бұрын
use nodemcu+relay and flash with sincric pro control or set routine on google assistant on your phone for the way you want for free.
@GOPALJHAlife3 жыл бұрын
alternatively use 555+relay and set it for half hour astable multivibrator output controllong relay
@sarabjitsinghsondhi59603 жыл бұрын
Simple and well executed
@msh1830 Жыл бұрын
kzbin.info/www/bejne/l5Cll6hnjbx6o6s watch last 30 second of my video. i explained withstate table and state diagram
@maksudrakib9959 Жыл бұрын
Supply for the pump is used in AC or DC? Can it possible by 9v battery and 5v relay?
@neerajkumarchandra9877 Жыл бұрын
Thank you sir for providing knowledge , but i m facing issue with this circuit whenever i do on this circuit my 555 Timer IC got burnt . i copied all component and circuit diagram exactly same as you provided us but it is not working. pls suggest me what to do....
@devanesh5791 Жыл бұрын
do u finished it??
@maheshraaz4915 Жыл бұрын
What are the main supplies kindly tell us ...is there and ac power supply ?
@debabratabasu8501 Жыл бұрын
The tap is going off position before reaching stop option. It has a doubt.
@illia543 жыл бұрын
Excellent circuit
@TechStudyCell3 жыл бұрын
Thanks
@bappaelectric3052 жыл бұрын
Bro 1 question answer please, isme components me 1k, 22 k, 180k,1m, sub 0.25w compalsary hai kya 1/4 w nhi chalega kya or, 2 question answer please, me isme 6v ka relay use kar raha hu ku problem tho nhi hoga na, resistance ka velue change kar na padega kya , capacitor ka bhi bolo,
@RSAT019873 жыл бұрын
Nice
@abdurrahmansarker02 Жыл бұрын
Can i use this circuit as my home 1.5 Hp water pump? and will it work properly?
@kunalkahane94424 жыл бұрын
I want reverse function . When tank will full, I want start pump & when tank is in low level, I want stop pump . What can I do chenges in circuit .
@TechStudyCell4 жыл бұрын
Just place the red wire in middle and green wire on the top. In this circuit the pump will start when the water level touch the green wire and stop when water touch the red wire
@kunalkahane94423 жыл бұрын
@@TechStudyCell bro I chenge on off wire from 555 ic but still function not working reverse ....think deeply and tell me exact solution ...I I'm not e&tc engg ...I m mechanical engg
@abulbasher8542 жыл бұрын
How many distance it will work.?plz tell me
@teobenedict17332 жыл бұрын
Hi, to power thr 5V water pump did you use a 5V AC/DC adaptor connected to the main?
@autorodautomotivetechnicia87693 жыл бұрын
New subs..nice video
@TechStudyCell3 жыл бұрын
Thanks
@Kenjiro25 Жыл бұрын
Hi, thanks for sharing, justa doubt; this project works with 110-120v too?
@TechStudyCell Жыл бұрын
Please check out latest video on this kzbin.info/www/bejne/mJikg6SlqLBqipY
@dominicroyis36422 жыл бұрын
pls show what are you doing with DC jack
@crazygaminglive72210 ай бұрын
Pls reply my que fast 🚦🚦🚦 What os the supply for the motor ??? Value of it for small dc water pump????
@anilpalithakarunanayaka58493 жыл бұрын
grate job
@TechStudyCell3 жыл бұрын
Thanks
@23saurabhdethe9610 ай бұрын
Can i Use 220V instead of 5V pump
@mphaneefakvr3 жыл бұрын
Very good 👍
@TechStudyCell3 жыл бұрын
Thanks
@okgoogle92162 жыл бұрын
If I am using 12v dc pump then anything I have to change in this circuit?
@draculadrac95662 жыл бұрын
Can u please share us the design with equations its necessary for doing it as project in collegs
@man-x-man Жыл бұрын
try a syphon to empty it quicker
@arulmk32533 жыл бұрын
Super work
@TechStudyCell3 жыл бұрын
Thanks
@bluestack11233 жыл бұрын
can be used on 2 Horse power Water Pump (i.e. 6 to 9 ampere)? any component need to be replaced else SPDT Relay ? and what Relay can be used to support maxximum of 9 amperes for 30 minutes until the water tank is filled as per the censor wire. Look to hear for experts.
@sarang26832 жыл бұрын
It's good but how to use in water heater boiler
@anandjoshi8554 Жыл бұрын
i assembelled full circuit on breadboard...led/relay get on ...but no ''''on off '''''with sensor in or out of water !!!!!(in total I had assembelled two more circuit like this...all facing same problem...no sensor activity !!!!!
@mmtechchannel8002 Жыл бұрын
Dear Sr.What software do you use for skill size mm × mm on A4 or Docx.
@asadullahkhan14543 жыл бұрын
Even without the wires in tank are connected..the pump switch on and doesn't cut off ..what can i do
@SuperThirugnanam Жыл бұрын
Super demo.
@moseslawrence9200 Жыл бұрын
Please my question is what to w collect to the "SUPPLY FOR PUMP" is that a switch?
@whiterose7203 жыл бұрын
bro which capacitor is used next to 555 ic the yellow one. Can U share.please......... I want the value of that yellow capacitor
@nizamalakhil3223 жыл бұрын
This is not capacitor.. It's a wire
@lexyjilltevesbarrientos6221 Жыл бұрын
Where can we buy that electrical board? I'd like to make one like that.
@TechStudyCell Жыл бұрын
it just a plastic sheet
@amjathamjath25093 жыл бұрын
We can use big water tank
@vvijay23873 жыл бұрын
is the supply 220v ac is this ok for 1hp pump
@TechStudyCell3 жыл бұрын
Yes 220v. The current rating of relay should be greater than motor max rating.
@whiterose7203 жыл бұрын
@@TechStudyCell bro which capacitor is used next to 555 ic the yellow one. Can U share.please......... I want the value of that yellow capacitor
@nizamalakhil3223 жыл бұрын
@@whiterose720 it’s a wire
@moeaungu1251 Жыл бұрын
I do according to your diag for my home water tank and i still cant catch up
@realexperiences68312 жыл бұрын
Bro plz clear the value of resistance either it is 22k ,180k or 22,180 ohm
@danielandrooze21792 жыл бұрын
I have one doubt ...if i connect this circuit in my motor..... what is the maximum hours it can be run
@hanigokavarapu97672 жыл бұрын
Is this circuit suitable for 1hp submersible motor ...? If not, what should we do ... Is it enough to change the relay and make any other changes?How much relay should be used ...? Please tell me bro ...!
@hanigokavarapu97672 жыл бұрын
Plear brother reply my dout... I am electrician
@anandjoshi8554 Жыл бұрын
use a compatible dc to ac ssr in place of the relay (if u know how to connect the ssr)
@المهندسللمعلوميات-ع4ك3 жыл бұрын
Good channel
@sivanmonippally3 жыл бұрын
i have borewell. compressor motor with starter is used. Can I run with this?
@chanrashekharmirajkar10973 жыл бұрын
We provide full automatica water level controller for submersible pump running with panel type .
@eissaahmmadi35953 жыл бұрын
Thank you sir
@delrstudio.22523 жыл бұрын
Thank you very much
@TechStudyCell3 жыл бұрын
You are welcome
@josebolanos30913 жыл бұрын
there I have an idea for another project, and so you do it is a controller for a voltage stabilizer system with transformers
@tronoclyde811610 ай бұрын
How much supply needed sir?
@ebucior3 жыл бұрын
Have you noticed any problems with corrosion of the wires submersed in water? If yes, have you solved it somehow?
@chanrashekharmirajkar10973 жыл бұрын
Use magnetic float sensor.
@ebucior3 жыл бұрын
@@chanrashekharmirajkar1097 Thank you for your answer, but wouldn't it require additional controller?
@ebucior3 жыл бұрын
In several videos (including this one) I saw just bare wires and I was a bit concerned about corrosion and wonderd how to cope with that. I assume that it would not be possible to just connect float sensor to the circuit presented in this video or maybe I am wrong?
@anandjoshi8554 Жыл бұрын
@@ebucior use separate magnetic float sensor in between each of the three sensor wire in the tank...with nc OR no setting...that way..wire will not get corroded
@aswinidhas41693 жыл бұрын
Can we use battery for Power supply
@chrischristodoulou17313 жыл бұрын
Does it work with pure Distilled-Water OR ONLY with Tab-Water? Thanks, Chris
@TechStudyCell3 жыл бұрын
For pure Distilled-Water this may not work
@chanrashekharmirajkar10973 жыл бұрын
You can use magnetic float sensor or cable float sensor.
@kaludharajeeya Жыл бұрын
Please make underground tank on of and ground
@yasarme33863 жыл бұрын
In this bucket what switch you used for water level Please reply
@TechStudyCell3 жыл бұрын
In bucket we are sensing the water level. Here 555 Timer controlling the motor
@Dash-Ø7-X3 жыл бұрын
One question sir if u got time please reply will be so helpful for me ?? So the question is that I have a water supplying line for my garden which supplies water only for half hours ,so I want a sensor which can detect when water comes an goes so that when water comes my pump will start and when it goes it will stop .
@augustusdeg6705 Жыл бұрын
Install a flow switch on the discharge or output pipe line of the pump ma'am/sir. That way, if there is no water to be pumped out, it will not run the pump on start, or stop the pump if it has started and no water is pumped out.. ..
@ManojKumar-yv2pk3 жыл бұрын
Is it usable with submersible
@chanrashekharmirajkar10973 жыл бұрын
No
@luqmanibrahim26062 жыл бұрын
Thanks Please which program used for the design??
@johnpatrick64152 жыл бұрын
What if i change the water pump to a 12v water pump? What relay and power supply should i use?
@msh1830 Жыл бұрын
kzbin.info/www/bejne/l5Cll6hnjbx6o6s watch last 30 second of my video. i explained withstate table and state diagram
@jigarshelat5998 Жыл бұрын
Sir i make but not cutoff dc plz help
@sarockpashotan39383 жыл бұрын
ا It was great man.thanks too much.
@TechStudyCell3 жыл бұрын
Welcome
@CRACKIITJEE3 жыл бұрын
Please also teach how this works otherwise what's the use of it. Even if I would be able to make it, It will be called as copy or cheat but not creation.
@jaimecases3426 Жыл бұрын
Hi is this project possible for arduino uno?
@tanveergsaudagar Жыл бұрын
Resistors ( 🤔R5 , R7 what does this number mean) (✔️ 2no ) 0.25watt Resistors ( 🤔R1 , R2 ) 180k 0.25watt Resistor ( 🤔R6 ) ( 🤔R3 , R4 )
@Hori9113 жыл бұрын
How many voltage supply in pump?
@iffee1003 жыл бұрын
What about electrolysis action on sensing prods??
@chanrashekharmirajkar10973 жыл бұрын
Use magnetic float sensor.
@danielcavi42043 жыл бұрын
How i could adjust the MAX and MIN water levels with a potenciometer? How can i insert that potenciometer here? Pls need answers for pass as a student! Thanks
@chanrashekharmirajkar10973 жыл бұрын
No need of potenciomerter , adjest senser wire up and down to adjust required level.
@victo_origin2 жыл бұрын
Bro mera circuit chal gya ha lekin band nhi ho rha chala ja rha ha motor me kya jaru
@lamc65163 жыл бұрын
Any possibility to make a Circuit for human body? 🤔
@seyedheartyculturenursery Жыл бұрын
Vay apki video dahky mani banayatha sab thike ha lakin (comon.and On.)tach hotahi band ho jata ha
@pranit_jadhav_37693 жыл бұрын
Is it works for high power motar
@VIJAYKUMAR-dv9gp Жыл бұрын
Connection complete vedio dalo ji
@lalocorona3 жыл бұрын
Creo que no es necesario electrónica ya que hay si al igual utiliza elementos mecánicos es mejor utilizar un sensor de agua común y corriente, hay veces en lo que la solución más fácil es la mejor
@ranjithkumarchinthala33573 жыл бұрын
It Need for every home.. to promote, Make Sell
@TechStudyCell3 жыл бұрын
I have modified the circuit to add more features. Will publish soon
@babukartik6124 Жыл бұрын
You should explain also.
@205bhuvaneswari93 жыл бұрын
Greetings to the Respected Sir/Madam. Can you please tell me how much cost for this total project?(including all Required components). Thank you so much sir/Madam for your great efforts 👏👏👏 Please reply to my message,we are going to do project on this.
@msh1830 Жыл бұрын
kzbin.info/www/bejne/l5Cll6hnjbx6o6s watch last 30 second of my video. i explained withstate table and state diagram
@dilprincedastan40753 жыл бұрын
If I want to use it with 1hp motor.. then do I need to change any other component except relay ??? And relay should be ac 220v ... Right ????
@TechStudyCell3 жыл бұрын
for 1hp motor you have to change only the relay. The current rating should be 30A at 220V AC
@ALLLEGALSOLUTIONS-IN3 жыл бұрын
@@TechStudyCell sir please mde a video on that
@dilprincedastan40753 жыл бұрын
@@TechStudyCell Thanks
@ECDINESHKUMARM2 жыл бұрын
Budget pls bro
@kinspiredskyee57974 ай бұрын
Currency?
@pabankumar8453 жыл бұрын
Can you please help me with the pcb layout gerber file