Hi friends today I am going to show Automatic Water level Controller for your water tank at home . It is very easy to make and low costing You can control up to 1hp motor by it. Thank you for watching .
Пікірлер: 190
@jagrutbhatt33013 жыл бұрын
Useful project in a simple way.
@satishyadav-rv9iz4 жыл бұрын
Can u tell where to fix led for low medium and full connection
@sujitmazumder12553 жыл бұрын
Thank you very much for uploading this circuit! I have tried your circuit, unfortunately when the tank is full, circuit doesn't cut off the power, hence the relay being on! All the parts were checked and they are found ok. Please give me way how to overcome this problem. Thank you.
@RohitGupta-wv5ct4 жыл бұрын
How to eliminate problem of electrolytic corrosion of sensor wires
@rahulkrishnantr53452 жыл бұрын
220 v comea as output so how you used small water pump? Please replay its for a project
@ejtrejos4 жыл бұрын
A greeting from Mexico. Thank you for your contribution to knowledge. It would be good to make a video where you indicate the control of the tank. This is to prevent the bomb from burning. In other words, to protect the pump in the absence of water. (empty tank). Thank you very much. When the tank runs out of water, the pump will not activate by asking for water (pump protection).
@carloscesarTHEBEST3 жыл бұрын
Excelente ideia. Otima sujestão.
@gopalshekar9862 ай бұрын
Great point! Greetings from India. We do have level controllers that detect dry run of the pump; that is, after several seconds of start up of pump, if there is no water flow at the outlet, there would be an alarm and the motor is turned off. We then have to manually inspect and resolve the issue. We could add more sensing too - motor temperature, abnormally long run (due to water being continually emptied) etc.!
@simranmoraes32602 ай бұрын
It’s working very fine I liked but can you do other way around motor stays off and when reaches high it turns on and off when reaches low point please 🙏
@YasvonthV.L-b8wАй бұрын
It will give in bread board to connect pls reply sir
@drv.ramanathannadella5614 жыл бұрын
Super. Simple and best. Where can we get the kit?
@NemishKr Жыл бұрын
agar auto start na lagaye only Off lagaye to chalegaa?
@RK_Patnaik2 жыл бұрын
Is it shock proof , shock neni lagega ya lagega
@ManishPrajapati-zm2cs Жыл бұрын
Bhai iss project me banane ke liye iska equipments kha pe milega or motor kon sa hai
@joserivas72513 жыл бұрын
Hola disculpa esa corriente que pasa por el agua afecta al cuerpo humano ? en caso que se conecte a un tanque de agua para baño ?
@acevikki4 жыл бұрын
Sir pura circuit bataiye na kis kis jagah connection Kiye Hai
@ridabest54264 ай бұрын
Hello, I tried but it didn't work. I used exactly the same components except that the water pump on my side is 220v
@jpscafe76483 жыл бұрын
Mas o projeto é show de bola!
@laurenceblaurence997211 ай бұрын
Hey! Sorry tell me the name of that black devices.
@shylendranponnani2 жыл бұрын
Haii hello ican help you? How built in 24volt adaptor usage to automatical waterlevel control
@nileshsutar90202 жыл бұрын
Can use any IC other than 555IC
@KrishnaKulal-lj5vt3 ай бұрын
Bro I did this but relay bar bar fuse ho raha he heat hoke melt ho raha he kya kare😢
@diyexplorer87285 жыл бұрын
Good one! I can use this on my water tank.
@gunjan_3 жыл бұрын
Just use opamp
@luqmanmpm4 ай бұрын
It turns off automatically but does not turn on automatically what was the reason
@anikbanerjee15314 жыл бұрын
I can use the battery of 12 volt please give me the diagram of the circuit minus plus
@laurenceblaurence997211 ай бұрын
Sorry,tell me the name of that black devices.
@dhruviachaudhari8752 жыл бұрын
full of details this model like cost, components, minimum & maximum price etc.
@bhasvataprajapati24494 жыл бұрын
Good Very good
@rajkumartamang64623 жыл бұрын
What is the specification of dc adapter you use
@Lovetolivetruely4 жыл бұрын
How can I make this for one way with a sensor or a switch? Maybe you can help me with what I'm looking for. I'm buying a 129v electric water dispenser. However it doesn't come with and automatic shut off valve. I am hoping to find something automatic that has an automatic switch or sensor that will allow the water to pump and stop. Kind of like how alarm system sensors or a type of toggle that when something is moved or a door is opened it activates. I hope I'm clear... Would you happen to know what I could buy that would do that that I could connect to the water dispenser and have it automatically activate and deactivate? I'm open to suggestions. Also must be a very small application that I can mount to a wall or pole or rod... Thank you and anyone who can help.
Two level switches and a relay will do the pump automation.
@bobbysingh77992 жыл бұрын
Sir mene yes project work tyar karna hai
@Raj-pk4ey Жыл бұрын
How can I use this for 1HP motor ?
@indiangmv31802 жыл бұрын
What is voltage rating of the water pump?? that you are using
@om_meet71 Жыл бұрын
Mas klo saya pesan, kirim ke.SMG harga brapa. Urgen dispenser galon bawah saya rusak.
@homoudalyahya46183 жыл бұрын
You just demonstrated your skills without showing exactly how did you wire the 555 timer. The diagram doesn't show how the pins are connected and the numbering you used are misleading. Correct me if I'm wrong.
@ntpawar19824 жыл бұрын
Dear sir please that how to 1 hp sumrsible pump with stater conection
@mohanrajselvaraj48314 жыл бұрын
Wat if lower tank has no water
@sudheertantapureddy68274 жыл бұрын
Sir , can I use diode in4004 instead of in4007 please relay me fast
@mohammedsajids25173 жыл бұрын
sure u may
@surajitsardar71784 жыл бұрын
Please tell how much voltage the motor you use.
@creativeetc4 жыл бұрын
220v
@sdj71224 жыл бұрын
@@creativeetc Please draw the DC connection on relay
@Sri20.963 жыл бұрын
2hp moter also same circuit working
@Santan__darshan9 ай бұрын
भाई layout dedo pls
@مصطفىالملكي-ب7ض3 жыл бұрын
جميل جدا
@subashj50894 жыл бұрын
But good
@hazzardfraeed Жыл бұрын
please can explain by arabic please
@danielferrari1141 Жыл бұрын
fantastic
@NarinderSingh-ys9qz4 жыл бұрын
Respected sir I am from mohali I watched your vdo I tested your project with glass of water and it is correct my half HP motor work good but with water tank it not work what's recommendations for it I hope you will give me answer
@jatinderkumar19464 жыл бұрын
When 12v supply going to tank than it is drop because water pipe is grounded so use flot switch other wise your time & money waste .i also used but these circuit are failure at 20, 30 feet.
@sanjoymondal16584 жыл бұрын
Naked of two wire +12 v and pin 2 should be closer.. In tank You can all +12 wire( in water of tank) should be naked.. And use very small wire for pulse..
@venkateshprasad1652 Жыл бұрын
If ckt with values of components had been provided it would have been helpful
@Saikiran-tm3qk4 жыл бұрын
water would get shock. To us
@rahulkrishnantr53452 жыл бұрын
Bro
@lawalmohammed833 жыл бұрын
Relay making noise making
@niju714 жыл бұрын
Circuit diagram
@mdevjani13 жыл бұрын
Submursible pump kaise honga
@PopatZaware-z6c9 ай бұрын
Does not. Work
@subashj50894 жыл бұрын
Onnum clear illa
@rathodhardik78123 жыл бұрын
Nahi work ho rha hai apka number do
@mdrjrana42855 жыл бұрын
হ্লল্ললুহজ্ঞভবফগভহঘগফহহ
@yashdahibhate75178 ай бұрын
Very amazing bro i try this.. 100% worked.. 💯🔥👌🏻
@jpscafe76483 жыл бұрын
Mas o projeto é show de bola!
@Educare944 жыл бұрын
Please draw the DC connection on relay
@vijayendirangiridharan61134 жыл бұрын
Can this system work on 5 volts?
@aualtinarama32624 жыл бұрын
hello is it possible to do the opposite of this circuit? So when the tank's full, the engine's going to work, and it's empty.
@ji8in4 жыл бұрын
Ofcourse .... Connect the motor to the normally closed pin of the relay. Thus when the tank is full the pump will start working... When the water level drops below the threshold level it stops
@vigneshm3484 жыл бұрын
can i use 12 volt 1 amp adapter?
@isaacsmandigo91794 жыл бұрын
Interesting circuit system. Can please do one that pumps water out when the tank is full please
@rajatmondal57013 жыл бұрын
doesn't work,, the high level wire is of no use.. basically mid and low wire are the main wire,, there is no need of timer ic ..stop making people fool!!
@Mr.Sankya11 ай бұрын
Yes bro i tried 😢 and waste 130 rs but not worked
@Hrithikdas9992 жыл бұрын
I've made this with 230v ac pump but can this circuit work on 12v dc pump
@rajasidhu268 Жыл бұрын
you can use 12v relay and control any 220 device
@michaeldominiccruz86784 жыл бұрын
Can I use 9v battery instead of 220v, for a 12vpump?
@creativeetc4 жыл бұрын
yes you can
@vennela27c.8th43 жыл бұрын
Can u plz say how much does it cost?
@madhabsikder9670Ай бұрын
Will it work for 1HP motor? What are size of the apparatus?
@kalidoss20152 жыл бұрын
But this circuit is not use in water motor , because the relay that you used in circuit is 7-15A.......
@mohammadabusayeedbhuiyan32422 жыл бұрын
U can use magnetic contactor for run 1.5H motor
@pssuresh14 жыл бұрын
Good work, please tell 5v supply circuit ,cable maximum length ,can add water level indicator to this circuit.
@siri779544 жыл бұрын
Sir i have open well in my farm field that well will fill once in a 2/3 day's and it is far away from home and i want to wait for power supply (supply provided by electricity board in shift wise)it's difficult to go and come plz kindly give modified circuit for operating irrigation pump when well is full and off when well getting empty .sir i am waiting for you replay kindly help to this former.
@embeededtinker70054 жыл бұрын
Srikantha M.B , I've a solution for you problem...! whatsapp me @ 9989800949
@dhruviachaudhari8752 жыл бұрын
please it's urgent so as soon as possible fast reply
@jpscafe76483 жыл бұрын
Esta horrível essa imagem do esquemático, não tem nitidez, fora de foco. Creio que é por isso que tem tanto Deslike. Todas as imagens estão ruim!
@mhradhanpura6730 Жыл бұрын
You are sels device
@HarishDebnath-d2x5 ай бұрын
Sir muje ak bana kor doge plz
@mayurkhan7.8.64 жыл бұрын
Sir mujhe es project ki pdf file chahiye thi plz aap avelable krwa do
@yuvrajparge97693 жыл бұрын
Muzhe bhi chaiye
@ShyamKumar-vv1gi5 ай бұрын
🫶
@pvkexperiments.447611 ай бұрын
What is the adapter rating is 500milli amps or 1 amps Because i tried this with 500 milli amps it works but in 1 a it wont work
@SocialForest-z4o11 ай бұрын
I made the circuit. But when the motor starts the base register of bc547 and 555 ic gets very hot. What to do ?????
@yuvrajparge97693 жыл бұрын
Sir can you tell me which motor yiu have used?
@NemishKr6 ай бұрын
Can i use this for auto Off Only .... i do not want this to turn ON automatically
@goutamkrsah95113 жыл бұрын
Working hai ki nhi
@anandhavignesh15784 жыл бұрын
My circuit is not switching off....its continuously in on state...pls help
@javierrd78185 жыл бұрын
Excelente.Favor el plano del Circuito
@faizanbukhari93344 жыл бұрын
I want to run 220v motor through it how can i do that?
@neotecwaterlevelcontroller40314 жыл бұрын
Contact us email neoteccwlc@gmail.com
@laerciosilva5904 жыл бұрын
@@neotecwaterlevelcontroller4031 ,vc não tem o desenho mais detalhado?
@NemishKr11 ай бұрын
Will it work With 1000 litre Tank and A Submersible Motor ?
@raimundoporesrgp36984 жыл бұрын
Can i use motor listrik i didn't see it thas why i still confuse
@padmarekha95722 жыл бұрын
Sir I am doing project My project name is water level controller by using pic micro controller In our project we use two pics sir First pic is 16F54 Second pic is 12C508 The first pic is giving connection between sump tank and water tank.(overhead tank) The second pic is only used in overhead tank I want circuit diagram for both pics and also I want code .
@mohamedabrar78684 жыл бұрын
what is that sensor wire. please send the name of that wire and photo
@baldevsinghgill79732 жыл бұрын
Not clearly shown components and their values
@vinaykale92622 жыл бұрын
can some give the name which equipment used in this??
@anandhavignesh15784 жыл бұрын
Whats that yellow and red wires are for? Kindly answer.....
@PREMKUMAR-wz6gq2 жыл бұрын
A little explanation would have gone a long way.
@sandipoob36103 жыл бұрын
project to accha he lekin isme ak dikkat he..ye to only uppar ki tank ka project he agar iske sath under ground tank ka system hota to or bhi accha ho jata..or isme agar full tank hone par buzzer add hota ho to vo bhi kar dena.... try to upgrade your system with second under ground tank ...
@mgold46853 жыл бұрын
Etsy...Solar Well Pump controller
@sudheertantapureddy68274 жыл бұрын
It worked but my ic is burning always
@ninyomansuhargayasih1458 Жыл бұрын
Sensor ke kaki no 6 IC tdk bekerja,apa yg salah?
@joker57.2 жыл бұрын
ज़ब वायर 3 लगाते है तो दूसरी मंजिल पर वायर रेसिस्टर बदल देता है तो सर्किट फेल होता है मैंने स्टील वायर भी लगाया सिल्वर वायर भी लगाया ये 7 मीटर बाद सर्किट फैल हो जाता है 5 मीटर तक वायर मै काम करता है
@sasthamoorthi-gt1id Жыл бұрын
Bro work aagala bro 12 volt supply poga kooda mattukkudhu