Didn’t buy Monroe’s conversion kit but for anyone looking to tackle this job I would 1000% recommend this video, made the job so much easier! Took about 4 1/2 -5 hours start to finish! Very well done Monroe! Thank you!
@jqscooby2684 Жыл бұрын
It is a great video. My luck, it would take me 4 1/2 - 5 weeks and then I would have to call a wrecker to come pick it up to have it done by a professional.😁
@DMN90210 ай бұрын
It's actually pretty straightforward, need a good jack, stands, impact and some wretches. Took me about 6 hours in the driveway. I have moderate mechanical experience
@MC-qn3sy10 ай бұрын
@@DMN902 I built my own kit when I swapped the air ride out of a rebel two years ago. 4 1/2 hours for me but I also had help and some machinery to help lift the truck up a bit higher to make installing the coil springs in the back easier
@basedlibertyprime2 жыл бұрын
Using this video as I’m doing the conversion right now and I just got to say that rear upper strut bolt is a real bastard.
@Mr1eyeScott2 жыл бұрын
Good to know 👍. I just bought this kit today and should get it in a week. Any other pain in the ass things I should expect?
@basedlibertyprime2 жыл бұрын
@@Mr1eyeScott crawling under the truck to torque stuff once the truck is back on the ground can suck but that probably depends on how big you are, I’m a large dude and I’m not a big fan of tight spaces.
@stopdalies2 жыл бұрын
Any special tools to recommend? Thanks in advance.
@Mr1eyeScott2 жыл бұрын
@@stopdalies only the 21mm bent wrench. If you have an assortment of impact tools, they do make it alot easier I did put a 3" leveling kit on while I was at it. Because I didn't take off the axle nut from the CV axle I had to pry very hard to get the strut over the bottom control arm. I pulled the CV axle apart on the inside and I couldn't get it to go back in and ended up buying a new one. Also if you bought the module that turns off the Service Air Suspension message, its is easy to install and follow the instructions. BUT DO NOT take out the fuses like it shows at the end of the video, because I did and the message kept showing up. Then when I put the fuses back in, it went away.
@stopdalies2 жыл бұрын
@@Mr1eyeScott will keep this screen shot so I can look at it. Thank you for your advice.
@PRO4XKEV3 ай бұрын
This type of work is a cake walk for me.
@deadwood3764 Жыл бұрын
Doing the Kit exactly as video.Less the lift.Front -L was 1st had to use long metal concrete pole to dislodge the upper ball joint as pickle forks did not work.Was a real tough nut.was also very heavy to lift new strut up and have holes align.Used a 2x2 19" to hold down so it would fit in .Not as easy as video.But very doable for the reg guy.On to pass side today with my tips i learned.
@jland904Ай бұрын
I will be doing this tomorrow gotta go buy some tools. Wish me luck
@georgenavarrete429118 күн бұрын
Does it ride better ? And is it the same ride height ? My bag sometimes leaks and sometimes don’t but often times it’ll deflate the rear while driving so it gets real bumpy
@homiehomerson2705 Жыл бұрын
Excellent video! They should all be made this way. Keeps things very simple. A narrator just complicates things.
@renegadearms2 жыл бұрын
Excellent instruction video of this job.
@SURENG-z7d Жыл бұрын
We installed the conversion kit and removed the mentioned fuses and relay while batterie connected and remove battery connection and reconnect. But still We are getting a air suspension warning at start up still. Any advise? How we can remove the service air suspension warning? Thank you
@jermonesmith702210 ай бұрын
Alpha obd
@tenadiamond1142 жыл бұрын
Can you leave the ride sensor in place and tape the air lines only?
@MrBlackbutang2 жыл бұрын
Does this kit work for eco diesel? I would think that you might need heavier coils? Thanks
@isaiahvasq52 Жыл бұрын
I did it to my eco.
@mrchrisknight3158 ай бұрын
There's better kits out there that won't require missing the rear bump stops. And there is a better way to get ride of the error message and the cluster info for air ride.
@LouieLouieUSMC6 ай бұрын
How did u remove. I have obd2 and still keeps coming back. Thanks
@johnnnyo110 ай бұрын
Where did the bolt that holds the brake line go at 9:51 in the video?
@philoskill156 ай бұрын
Can you leave the stock bumper stops? they seems to have the same length in the kit i ordered ...
@suzanneheroux13002 жыл бұрын
My bumper stops are still touching the axle (I left the original in place). I am wondering if it is normal. I am no mechanic and it took me 2 days with the few tools tha I have. I do not know what happened but after 24h everything seems good.
@jermonesmith70229 ай бұрын
Did you bottom out alot ? I installed this kit and left my factory bump stops on. I bottom out alot in the rear.
@hondaracer304joey2 жыл бұрын
Fallowed the directions to the T still have service air suspension . Had to put a fuse back in because I lost my towing breaks any info to get the notification off ? I have the Alfa obd if anyone has tips ?
@Jerk13100 Жыл бұрын
Would this same video work if it’s an air delete and lift kit combo?
@cliffordsawyer2994 Жыл бұрын
Yes
@19liebers Жыл бұрын
This will also work for a 2017 rebel I’m assuming ?
@williamg.cabeza8476 Жыл бұрын
I have the same truck, did you us it?
@Rigo.253 жыл бұрын
What did u do with the compressor for the air suspension
@reynoldscs3 жыл бұрын
I'm sure they just left it alone.
@Neno13410 ай бұрын
Would this monroe conversion kit work for a 2015 Ram EcoDiesel ?
@bbooger93313 жыл бұрын
Ive been told by a shop that this proceedure would take 10-12 hours. Does that sound correct?
@vinnysotelo77293 жыл бұрын
Took me 8 hrs in my garage with a floor jack and 2 jack stands
@andriiturchenko77402 жыл бұрын
Sounds like a bullshit to waste your money
@woosta452 жыл бұрын
3 hours rear 4 for the front. But that also included a burger and some beers.
@joacobmx95 Жыл бұрын
4 and half hours with neumatic tool, good jack
@Ryan-ml2fc3 жыл бұрын
Does it throw codes?
@m3rdpwr Жыл бұрын
I heard just taking the fuses out, does not solve that message. AirDelete will rent you a programmer, but only if you buy their kit. You get your deposit back on the programmer, once you return it.
@austinwinters8122 Жыл бұрын
Why do they sell modules for $400+ to keep warning lights off when you can just take all them fuses out. Do the lights come on after you take all them fuses out?
@m3rdpwr Жыл бұрын
I heard just taking the fuses out, does not solve that message. AirDelete will rent you a programmer, but only if you buy their kit. You get your deposit back on the programmer, once you return it.
@raresonofrei57433 жыл бұрын
Hello, there is a part number just for the rear coils, not for the whole rear kit please? Thank you!!!:)
@graveydavey00743 жыл бұрын
Please do a Jeep Grand Cherokee conversion . Nice work
@calebjenkins35782 жыл бұрын
Do you have to drain the nitrogen system? If so how do you do that?
@JJustified2 жыл бұрын
no. nitrogen makes up about 80% of our atmosphere just vent it
@cudamgurung6821 Жыл бұрын
the rear spring did not seat properly on my ram 1500 2013. And it did not fit the 2 inch levelling kit as well. Is that normal?
@MonroeSuspension Жыл бұрын
Hi Cudam, our tech team would be happy to help you with this. You can reach out to them at 1-800-325-8886. They are available Monday - Thursday from 7:30 a.m. - 4:30 p.m. (CST), Friday from 7:30 a.m. - 4:00 p.m. (CST).
@hammer2732 Жыл бұрын
I need this done how do I get in touch with these guys?
@ethanochoa58823 жыл бұрын
Doubt I’ll get a response but this won’t affect towing or bed capacity of the truck
@vinnysotelo77293 жыл бұрын
Get you some Airlift 1000HD on Amazon. They are about $130. Airbags that go inside the coil spring and you can manually increase or decrease the psi depending on what you are towing
@MrBlackbutang2 жыл бұрын
What does this system cost ? Thanks Spooln272
@kingace9812 жыл бұрын
i would love to do this... but once i do all that would there be a warning light anylights
@m3rdpwr Жыл бұрын
I heard yes. AirDelete will rent you a programmer, but only if you buy their kit. You get your deposit back on the programmer, once you return it.
@maurygomez6422 жыл бұрын
What size is the backside bolt? Where you used the bent wrench
@bradteter92272 жыл бұрын
21 mm
@samhoffman15512 жыл бұрын
Did anybody find their truck sitting lower than when you had normal height air suspension? Some Amazon review stood they're truck sits low with this installed.
@hondaracer304joey2 жыл бұрын
I did I also bought a leveling kit for the front and spring bags for back I’m 7 1/2 “ on front and 7 1/2 on the back .
@samhoffman15512 жыл бұрын
@@hondaracer304joey I did a leveling kit and turned out perfect!
@suzanneheroux13002 жыл бұрын
My bumper stops are still touching the axle (I left the original in place). I am wondering if it is normal. I am no mechanic and it took me 2 days with the few tools tha I have.
@andriiturchenko7740 Жыл бұрын
@@hondaracer304joey hi, which spacers did you use for this(size)? Are 20in factory rims looking proportional to that height?
@LouieLouieUSMC6 ай бұрын
@suzanneheroux1300 u have to cut off the extension for stopper and install the one that came with kit. It does ride and sit the same. Actually better than that crap air suspension. I have 2015 rebel. Worked perfect
@robfinch24293 жыл бұрын
When removing the fuses, i lost my trailer brake controller. Is there a different way without losing trailer brake?
@MonroeSuspension3 жыл бұрын
Hi Rob, our tech team would be happy to help you with this. You can reach out to them at 1-800-325-8886. They are available Monday - Thursday from 7:30 a.m. - 4:30 p.m. (CST), Friday from 7:30 a.m. - 4:00 p.m. (CST).
@anthonym62 жыл бұрын
Put the F87 10A fuse back in. This will keep the trailer brake controller working. The system warning won’t stay on and everything works great.
@oda0111 Жыл бұрын
@@anthonym6 I'll have to try that later. Thanks for the tip!
@parteekboparai85113 жыл бұрын
Can I use any strut or does it have to be a conversion kit
@yoloxxjd13 жыл бұрын
Reading some forums, I think you can use any strut. But I’d do some more research tho
@cliffordsawyer29942 жыл бұрын
@@yoloxxjd1 did you find any info on this yet?
@clemm1892 жыл бұрын
Did anyone have to do alignment afterwards?
@hondaracer304joey2 жыл бұрын
Yes
@woosta452 жыл бұрын
Absolutely
@welksauto25953 жыл бұрын
We installed the conversion kit and removed the mentioned fuses and relay. We are getting a air suspension warning at start up still. Any advise?
@laughingatourlife2 жыл бұрын
I have the same question any luck with getting the message off and can you buy cover buttons for the up and down that we deleted??
@embeesl4y3r2 жыл бұрын
@@laughingatourlife I am about to do this conversion on my truck and my best guess is that you (if you have a WiTech 2.0 subscription) will need to call the dealer and give them the VIN and tell them to remove the sales code for the ASCM (SER seems to be the code according to TSB 08-051-16). Assuming they do it when they say they will, it should be available in the cloud to download to the truck within ~30 minutes. At least this is how it works with adding the WCM/WIreless Control Modules to FCA vehicles, or the LPL/Pickup Box Lighting for the Rams. I assume that deleting should be similar to this.
@embeesl4y3r2 жыл бұрын
I just looked in Tech Authority for my VIN and it says SERS is the Air Suspension, 4-Corner. Either way, I will call the dealer and let them know to remove SER/SERS and hopefully it works. Will update if it does. Still planning to pull fuses as well.
@marcwa50672 жыл бұрын
Try using ALFA OBD to remove the feature from the PCM.
@anthonym62 жыл бұрын
My warning message comes on every time I start the vehicle for a few seconds and then goes away.
@johnmiller56543 жыл бұрын
How much does this cost
@vinnysotelo77293 жыл бұрын
$500 on Amazon. I just did mine
@kennethlovett10103 жыл бұрын
@@vinnysotelo7729 what brand did you find on Amazon
@vinnysotelo77293 жыл бұрын
@@kennethlovett1010 this same exact Monroe kit
@kennethlovett10103 жыл бұрын
@@vinnysotelo7729 Ok! My RAM has dropped air suspension sucks
@vinnysotelo77293 жыл бұрын
@@kennethlovett1010 same exact reason I replaced mines also. The compressor costs $550. The front air bags cost $330 each and the rear ones $180 a piece. It was cheaper for me to change them out to coil springs and add some airlift 1000HD to the rear coils. They're only $140 on Amazon and can just manually inflate them when you need to haul heavy loads
@josephhammers98833 жыл бұрын
Does this get rid of all service lights for air suspension?
@bluefive52 жыл бұрын
No.
@woosta452 жыл бұрын
You have to flash the computer to Uninstall the air ride system.
@joacobmx95 Жыл бұрын
how do you flash it? with a ecu remap or a good scanner?
@m3rdpwr Жыл бұрын
I heard just taking the fuses out, does not solve that message. AirDelete will rent you a programmer, but only if you buy their kit. You get your deposit back on the programmer, once you return it.
@jermonesmith702210 ай бұрын
Alphaobd
@jesseroberts22852 жыл бұрын
Do you have to remove the old jounce bumper or can you leave that there?
@hondaracer304joey2 жыл бұрын
Left mine no issues using this kit.
@Mr1eyeScott2 жыл бұрын
@@hondaracer304joey any issues since making this comment? I bought the kit today and should get it in a week. Didn't really understand the point in cutting off the old bumper if it's still good.
@hondaracer304joey2 жыл бұрын
@@Mr1eyeScott I left my stock ones on as well no issues 🤷🏻♂️
@jermonesmith702210 ай бұрын
Do you guys have a noise over hard bumps? Like bottoming out in the rear going over hard bumps at higher speeds?
@jacobengle55672 жыл бұрын
I have a 2015, mine looks different. wth.
@chandler1francis3 жыл бұрын
Can you install a lift kit after this?
@reynoldscs3 жыл бұрын
Yes, But if you want a lift kit, this would be the time to do so. Front is usually a preload spacer on the front struts ( or lift spacer bolted on top) & spacers on rear coil springs, un less you are going a 6" kit which is a different setup with way more pieces.
@davidc96872 жыл бұрын
Wait do you need to buy a conversation to install a 4 inch lift kit??
@andriiturchenko77402 жыл бұрын
@@davidc9687 no, you probably need to buy some new control arms. You can still buy a 4” spacers and go with your stock upper control arms, but many people recommend not doing so