Tesla Bifilar Coil Electromagnet Mystery Solved

[@ocdbnoex1938]

So, what is unusual in this oscillating circuit? What the purpose of video😂?

[@ArkiverUnifiedEnergy]

The discovery of a working "Electric and Magnetic Condenser." Not a capacitor. More info: kzbin.info/www/bejne/i2Ore4hrl52prdk & kzbin.info/www/bejne/hHnaq4aohLyUobs

[@ocdbnoex1938]

@@ArkiverUnifiedEnergy what is your background in that field? Just a simple question. I want to know, where they are teaching "magnetic field" storage fellAs😂. Isn't any chance that your society can store a gravitational field😂? Would be very useful for me😂.

[@ArkiverUnifiedEnergy]

@@ocdbnoex1938 Self taught. Eight years studying what the pioneers in science were doing, 1800's to early 1900's. Studied thousands of patents and books. There's a lot that was lost, forgotten, and intentionally not used. Some things other technology wasn't there yet. I watch what is being done here today and compare it to what was being done back then.

[@Magneticitist]

@@ocdbnoex1938 Universities. They teach magnetic field storage at Universities. Edward Leedskalnin also taught a little bit about it in his book but he was doing it a different way.

[@ocdbnoex1938]

@@Magneticitist 😂🤣😂, Maxwell is surprised, for sure. What about to store for me a little amount of gravitational field? I want Einstein to be surprised too😂.

[@glasstronic]

A common sort of brush-less D.C. motor design. Induced currents switch the transistors. That's been in use for decades; nice to see it demonstrated if not adequately described. Nice construction there! Superb mechanical and aesthetic aspects to your art.

[@jeffiscool1805]

Maybe the coolest video I've ever seen. I like the way you think, and your fabrication skills aren't too shabby either. Impressed and subscribed. Cheers, and keep it up.

[@DaminalTheAminal]

Knowing that free energy is possible makes this the best time to be an inventor! Keep up the good work!

[@azarahwagner2749]

NOT FREE , a power supply is being used and paying power bill to run it , see not free

[@JenkoRun]

@@azarahwagner2749 Just break the symmetry of the field interactions and use a small source to excite a larger source, simple stuff.

[@picdoran]

The rotating brass wheel near the bifilar coil could be creating eddy currents. The steel piece attached to the magnets bend the flux lines closer to the magnets, at least on the side next to the two magnets, possibly interfering with the flux lines between the coil and the magnets, Replacing the brass wheel with a thicker plastic wheel and embedding the two magnets into the plastic wheel(s) without using the steel strap may produce a cleaner signal and less drag.

[@chifoltz9023]

I think the secret of the bifilar is related to the nature of Bucking coils cancelling out the Lenz effect of magnetic resistance to the current with resonance. The Bifilar is just a more compact ingenious way to do it. If you have the speed variation, torque, COP, Q, etc. I would definitely like to see more on this device and it's name if it has one, thanks for your excellent work!

[@ArkiverUnifiedEnergy]

It's a condenser.

[@chifoltz9023]

@@ArkiverUnifiedEnergy Condenser as different from a capacitor in some way? I know the L-C, inductance - capacitance of the coils has everything to do with the resonance and cancellation of the Lorentz resistance to the current. Is that what you mean?

[@dennyoconnor8680]

That LED is a fly-back snubbing diode. Same reason we put a back diode across an induction coil for protection from voltage spikes when the relay contact opens, the field collapses inducing the fly-back voltage.

[@DavoY2K]

You make perfect sense. I understand how you are saying the dielectric counter space expands and contracts at your bi filar coil. Nevermind the naysayers. You're on to something. If you haven't already check out what Master Ivo is doing and saying with bifilars and Theoria Apophasis is doing and saying with magnetism and dielectricity. Great work. Thanks.

[@domestinger8805]

Ivo is clueless

[@lukiepoole9254]

@@domestinger8805 He's not lol lmaooo

[@MasterIvo]

I just love these magic bifilar coils.

[@sundiesel1232]

Master Ivo , Understanding something causes love for that thing to have a greater meaning. Your work with these coils makes you see within, what others may only be looking at. Best regards

[@Supernumerary]

Bifilar and Trifilar enameled wire is commercially available. Small gauge, ideal for these types of experiments.

[@jimmurphy5355]

You really, really need to get an oscilloscope. You will learn a LOT. I think you will be amazed at how much being able to view the moment by moment voltages in the circuit can clarify what is happening.

[@AllanShura]

This does provide insight. Magnetism converted and polarized return pulse.

[@sundiesel1232]

Hi. Thank you for the great demonstration and clear explanation.

[@caileanparis9998]

This is dope Love the sound it makes too like a smooth locomotive

[@mikemadsen2716]

that is an important discovery.

[@alexanderfederowicz]

Do you realize that the Bifilar winding forms a capacitive charged storage of additional voltage per turn in the winding's... The Bifilar coil pinches mas-charge into massless charge space / a pressure bubble of massless charge forms coupled to the mass-charge electrons...So in essence you could form a Ultrapacitor with that coil, if you used a superconductive core... Now that we have room temperature super conductors being openly patented by the Dept. of the USN, this can become a Useful Ultra Battery, that can instantly store a massive charge of great energy density ! One must be very careful never to over charge these, as the meisner field when over charged beyond it's storage coherence levels essentially detonates releasing 100 % of the energy instantaneously as an expanding sphere of Light... More like an expanding Laser Sphere !!!

[@maxprophet2401]

2:08

[@homo-habiliss]

Place the same magnets with the coil on the other side at a 90 degree angle, and maybe the engine can provide itself. This engine is similar to those that use energy stored in Magnets when they are magnetized. About such engines, even in the textbook for students information is available

[@DJ_Koob]

so on each alternation you are moving the the energy transfer in collapsing of the magnet field back to a dielectric field around the capacitor?

[@srotovnikabc6919]

It is not a bifilar coil, winding. It is a classic double winding, that reverses magnetic polarity. The same as push-pull converter and motor.

[@pacopistones1561]

Congrats, you make a motor with a 27mW!!!

[@Kawique]

Very interesting. Magnets have same poles towards coil, or polarity alternates?

[@ArkiverUnifiedEnergy]

Magnets are opposite polarity.

[@Barskor1]

Carbon nanotubing as the coil wires would be amazing.

[@qedqubit]

wow ! best explanation of catching the back-EMF iv'e seen :-D !

[@upmperthay]

Add a variable cap in parallel, + maybe one in series, with, or in place of, the fixed one. Then you could control it completely.

[@ribb4200]

The pole in my back yard is also ringing. Mystery Solved.

[@hydniq3327]

I will try that circuit sometime. your motor looks great.

[@225rip]

Great video.

[@masterg9792]

you get free energy by combining a compilation of everyone 's networked ideas and simplified and most effective inventions together to work in unison and harmony that produces a powerful orchestra array of frequencies for real results. so if we take what Tesla taught us about simple wave form propagation of antennas transmitting and receiving frequency signal data packet bursts of energy and with a Tesla bifiler coil to receive the high altitude scalar energy wave form to transfer to a wireless induction high voltage Tesla Coil to boost the energy volts while at the same time use the incoming scalar ham am/fm waves to send a pulse signal to a low volt high rpm brushless motor with the bifilar wireless energy coil and a capacitor hooked to the power ports and the slow turning of the motor with multiple long cylindrical earth magnets n52 with apposing polls pointed outwards and a 1/2'' copper tubing roll with solid copper wire strands filling the inside copper tube circle that is a lil bigger then the magnet pinwheel on the spinning motor. then take that free energy generated from wireless antennas and frequency waves. then take that whole part of the free energy solution and add another invention and or idea to the solution like sonoilluminescence with frequencies on a water bubble molecules to create energy that gets hotter then our sun plus we could add solar energy and capacitor banks and batteries to store it all in. and has anyone load tested a mono-atomic gold/silver and graphene and water battery on any 12 volt power tools or vehicles or still not yet? i liked this explanation of the concept and ideas of harnessing even more variations of energy wave forms to utilise for everyday usability applications.and thanks for your videos as i have a better grasp of the depth and complexity of all the free energy surrounding most of us daily going to waste because we all dont fully understand energy and all of its shape forms waves colors temperatures etc. and real quick idea for a graphene battery is take monoatomic graphene atoms and add it all to the solution mix while you grow borax or quartz crystals or something like that

[@cynthiaayers7696]

You forgot the scrambled eggs on top. Hahaha...

[@matthewmcmullen2752]

Would it be possible to link the other half of the electromagnet to the other end, shorten the distance between them, and pulse them together?

[@NickDBrewer]

Great job. Your movie is very helpful indeed. Thank you for sharing.

[@Emprivan]

Wow, all you did was connect a transformer to a flipflop circuit. And I'm calling BS about your contraption causing a beeping oscillation at the mains on the pole.

[@alexanderfederowicz]

Do you realize that the Bifilar winding forms a capacitive charged storage of additional voltage per turn in the winding's... The Bifilar coil pinches mas-charge into massless charge space / a pressure bubble of massless charge forms coupled to the mass-charge electrons...So in essence you could form a Ultrapacitor with that coil, if you used a superconductive core... Now that we have room temperature super conductors being openly patented by the Dept. of the USN, this can become a Useful Ultra Battery, that can instantly store a massive charge of great energy density ! One must be very careful never to over charge these, as the meisner field when over charged beyond it's storage coherence levels essentially detonates releasing 100 % of the energy instantaneously as an expanding sphere of Light... More like an expanding Laser Sphere !!!

[@vincentrobinette1507]

The LED's need ballast resistance, or else, they will clamp the voltage caused by resonance between the inductance of the coil, and capacitance of the capacitor. There is a certain frequency, in which that capacitor and coil will naturally oscillate. The capacitor value must decrease on the inverse of the square of the frequency, because, the voltage increase raises current, as well as the capacitor becoming lower effective impedance as the frequency increases. Cutting the capacitor value in half, will allow an increase of voltage of 1.4142135,(square root of 2) and will allow the exact same percentage increase in RPM. As you increase voltage, thus, speed, you will also want to increase the value of resistance of the base resistors to the transistors, and the same value of resistance would also be appropriate as ballast for the LED's.

[@alvinsuperman]

Thanks for sharing and I think you hit it right on the head! one question though does the magnetic field grow i know you said it pulsed but does the field, with speed expand? again thanks for sharing your project and your thoughts very nice. keep up the good work. Al

[@ArkiverUnifiedEnergy]

There's a higher degree and area of change. Thanks, Mike

[@alvinsuperman]

thank you for that i noticed it with my rotors the faster they spin the larger the magnetic field thanks for your input. Al

[@Myreply59]

It's a well built machine in itself. Discovery is what it's all about. Making good use from the back emf makes it efficient. BTW, science has discovered that there are actually magnetic waves in the universe that ripple the fabric of space-time. So it is very possible that your machine had an effect on the streetlight pole. Tesla said to think in terms of energy, frequency, and vibration when considering the universe. Keep experimenting.

[@Myreply59]

Also, consider that the horseshoe may have the effect of concentrating and focusing magnetic pulses where the back efm fires them off like little bullets. I would conduct an experiment where you hang a piece of metal several feet away and see what happens to it. You can do this with a hanging magnet as well and see if it moves when placed a distance away from the machine.

[@pacopis]

What is the thickness of the copper wire?

[@ArkiverUnifiedEnergy]

30 AWG 0.011 inch.

[@windpowerandmore6310]

Nice work !!

[@Blue.star1]

Don't use npn transistors, junction losses , use low loss ones

[@scottwippel5871]

Do you really think the old days guys Who found this out by testing everything?

[@Memorybug]

Dear Arkiver, thank you for this Video! May I ask if the rotor´s polarization is + - (+ -...) ? All best regards from western euope!

[@Blue.star1]

Coil picks rf, Diodes convert , try shielding the whole device and earth the shield.

[@NareshKumar-yu2ov]

I tried replicating it but I fried the NPN transistor all the time , and no rotation, any help will be appreciated. I used speaker cable for bifilar setup

[@ArkiverUnifiedEnergy]

You need many turns to create a strong enough magnetic field for a given voltage. Transistors have a maximum current rating.

[@MrFreshwap]

@@ArkiverUnifiedEnergy I need help from how you make bifilar coil to turn on magnet

[@mundymorningreport3137]

@@MrFreshwap The bifilar coil, as Tesla's patent (and illustrated in the circuit diagram) is a coil that has two wires running next to each other of the same length. The end of one of them is connected to the beginning of the other, forming one continuous wire coil. However, unlike a standard single wire coil, the neighboring wire along every turn is exactly 1/2 the voltage potential of the other. This is the condition of a capacitor. In a motor, the magnetic flux is stored in the capacitance of the inductor. It is a flux capacitor. The simplest way to make it is to use a dual conducting wire. (Apparently, this type of wire is available commercially; not widely used in electric motors but in some limited applications of electromagnets) then make the beginning of one to the end of the other connection external to the windings. The connection between the start and finish of the two wires is made outside the windings and does not contribute to the magnetic field. You can also use two separate coils of wire, winding both at the same time; again making the finishing connection externally after the windings are complete. The capacitance energy that can be held by the coil increases with the square of the voltage driving the coil. Unlike a standard cap that has variations in the micro-formation of voltage/insulation differences due to the physical construction of the large surface areas of standard capacitance structures that lead to blow-outs, this bifilar cap equally distributes the energy it holds along the entire wire. With an air-gap and no amplifying core, this flux capacitor can have very high frequency and current response which was desireable in Tesla's spark-gap transformer. When wound around an amplifying ferromagnetic core, driven by an alternating current, the phase of the magnetism generated by the coil is shifted to align with the changing phase of external magnets. This creates a self-charging effect within the coil. As the coil releases the energy it captured in the capacitance, it captures the energy it generates with the released energy. The net effect is to neutralize the inductance, but not by cancellation, by self-capture. The coil only shows resistance, not inductance. With a ferromagnetic core, the current or magnetism is amplified. Excess electrical energy in the form of current is produced. The motor can be run on voltage alone (using dead batteries), which it will charge. Joe Newman used standard dry-cell 9-volt batteries in banks of hundreds of volts with his design and not only charged them up (non-rechargeable batteries) but also drove other motors and lights. Although Joe's design was not with a bifilar winding, it was with extremely long runs of wire. Thane C. Heins has many videos of this as applied to electric car motors. His patent application was denied as the motor design was patented back in the late 1800s. Joe Newman created a motor that had this effect with extremely long coil lengths (the speed of conduction is limited in wire, make the path long enough and the coil will not conduct current reflexively like a pure inductor would, effectively becoming capacitive). Joe's patent was denied due to the destabilizing effect it would have made on the economy. This is a disruptive technological innovation. None of the automakers will implement this technology into their vehicles; Thane offered it personally to all of them. Unlimited range, mobile generating plants would break the world economy, and disrupt the integrity of national borders as we know them. According to standard physics, creating energy is not possible. And regular theory does not adequately explain how EM induction works (there are paradoxes that go un-explained, and basically Maxwell's definitions are pseudo-science) as it would reveal that electricity is not fundamental, it is a composite that can be created from its component parts. An example of this is the power amplifying inductors used in phone lines, like the trans-Atlantic cable which cannot handle the amount of energy that it takes to send signals end to end. Self-amplification through regularly spaced capacitively wound inductors are essential to its function but denied as possible in power grids. This demonstration is low power, so the excess energy effects are minimal. It would be easy to overload the circuit components if you are not careful; the bifilar coil has an extremely large dynamic operating range that is unmatched by semiconductor components.

[@MrFreshwap]

@@mundymorningreport3137 Thanks for explaning with deatils

[@paulleftwick7782]

The brass is magnetic if it's moving that's dielectric ?

[@stephencrum530]

two years later and still no free energy

[@jameselliott9397]

What capacitor did you use?

[@ArkiverUnifiedEnergy]

A nonpolar electrolytic 100uf.

[@jameselliott9397]

Thanks... take a look at my videos if you have a chance. I will test that circuit on my devices

[@azarahwagner2749]

The “ sound “ …. It’s your bearings dude .

[@ArkiverUnifiedEnergy]

You were right the bearings where bad.

[@azarahwagner2749]

I found they get too warm and always fail at a certain ( sustained) rpm . I was thinking of a magnetic bearing ( free floating) instead of ball bearings. Probably using super conductor material would be better suited but then you have to cool them as well. Experimenting can become expensive.

[@sundararajann6007]

what is the input voltage?

[@ArkiverUnifiedEnergy]

0.9 volts 40mA

[@laminetheory5563]

you can try it with thyristor ?

[@correocarlosgarcia]

What is a Fowler coil?

[@ArkiverUnifiedEnergy]

Don't remember term.

[@dragon72tube]

IT IS A DIRECTIONAL WINDING?

[@donleibold9693]

PMBO 2020 is about to start ... watch for details!

[@aldebaranflash2663]

good job

[@catmando17]

way to go keep learning

[@hydniq3327]

great video

[@ArkiverUnifiedEnergy]

Thanks :)

[@markhodgson3045]

Haha so you have mains in your telephone poles

[@nexpro6985]

Your little motor affecting a street light forty feet away? I look forward to your experimental proof of that statement. I am going with another idea... coincidence.

[@ArkiverUnifiedEnergy]

I do have that ballast. 😁

[@PerpetualMotor]

I tried replicating the circuit, but I only got an oscillator. The LEDs light up at .4V and 13mA (like a joule thief), but I don't get any motive force out of the coil. I tried a lot of different capacitor sizes ranging from 10uF to 4000uF. They only smoothed out, or shut down the circuit. I am using an air core bifilar wound coil with 100 wraps (each coil - 200 windings total). Any tips on anything that I may have missed?

[@ArkiverUnifiedEnergy]

The electromagnetism will sink with a permanent magnet free to move. Provide there is enough electromagnetic field strength for a given voltage. About 1000 turns or more for 1v.

[@craigpierce7996]

You said you "replicated", but that couldn't be further from the truth. Your air core, 100 turn coils have nothing in common with these coils shown in the video. It's a beautiful build in the video. I suggest doing an actual replication, then discuss your findings...

[@mundymorningreport3137]

@@craigpierce7996 Wisdom that is missed by very large percentages of designers these days and also in the past. Tesla took advantage of this in his patent portfolio, applying for multiple variations that were mostly irrelevant to his discoveries and allowing common theory that he knew to be false to prevail in the world of hacks who tried to steal his designs. So many people have ideas how they think things work that prevent them from doing what is given to them without first messing with the design... And then claim its fake because they fail. This is a common error made by those that demonstrate that Tesla coils cannot transmit energy 25 miles or more as Tesla claimed to have done. They fail to realize Tesla was not transmitting electricity. And for one man who matched Tesla's feat, he discovered that his breakthrough brought the attention of military force. It seems these types of innovation are not entirely bogus.

[@mundymorningreport3137]

Air core generators have the distinction of very limited current capacity. Gerard Morin uses this to demonstrate a 30 amp generator can power a 210 amp load if sufficient EM windings are introduced into the circuit. He does this with a massive step up and step down transformer pair. The load he drives literally takes the energy from the transformers, not the generator. You see our power systems are driven mostly by voltage, but run on current... current is actually magnetism, not the flow of charges. It turns out flowing charges do not necessarily carry magnetism, which is why AC power factors and phase alignment of current and voltage is critical to efficiency of electrical systems. And as such, one can easily amplify electrical power by increasing the magnetism. When you are looking for motive force or magnetism, why would you limit the windings and also eliminate the ferromagnetic core? That core can amplify the magnetic power of a coil 1,000 times. And each loop of wire delivers the full potential of the total wire to that core, stimulating another full slice of magnetism from the core. However you think this device works, it could use some reconsideration. The design variations you implemented seem to validate these basics. Perseverance furthers...

[@craigpierce7996]

I can say that after years of casing Tesla's electromagnetic designs, I've finally have realized that the secret is in the electrostatic realm, not electromagnetic. Only a field can move at the speeds Maxwell describes in his special equations. Trying to create an event disruptive enough to force a current interaction with the surrounding natural E field (not free, it's already there and you're going to spend some bucks to get it) using electromagnetics is way off the mark. Electrostatic excitation is the only thing fast enough. Although the circuits look pretty close, its how they are used that counts. Tesla hid everything from everyone, including himself! The last version of his rotary sparking system would cost about $100K to build and would challenge any designer to replicate. It's stats are mind blowing!

[@yuseffnehru8612]

Thank you ☺️

[@ArkiverUnifiedEnergy]

You’re welcome 😊

[@Blue.star1]

I have led bulb of less than 1 watt, with three 3 mm mini white leds , touch tgem with hands, at appropriate point , they glow, forgot if my feet r earthed, May be terrestrial radio waves are feeding them ....

[@dougaltolan3017]

Do I get a prize for getting to 1:25 of this BS?

[@JenkoRun]

8:00 Sounds like a stream train.

[@robertwagner7439]

Nice💚

[@tufanirfan]

Alf is=loop Eye is=? Bet is=?

[@masterg9792]

and try adding a joule thief or buck back?

[@michaeldomansky8497]

Absolute ignorance corrupting infinite arrogance.

[@CMAenergy]

For give me for saying this. I think you better learn about electronic circuits first before you try to understand or explain what is happening

[@ArkiverUnifiedEnergy]

Ah! Conformity and riddles.

[@shawncalderon4950]

@@ArkiverUnifiedEnergyclever responce!

[@arthurcooper7031]

No such thing as free energy unless you steel it from the power company then when you get caught you will have a free place to stay and a girl friend named bubba !

[@mundymorningreport3137]

Denial is not truth. Free energy sustains everything that is in existence. It is easily captured and put to useful purpose. *Common phone landlines are powered by amplified electricity without consumption of any resources. *Lenz's Law is an artifact of bad engineering. *Maxwell's equations are the definition of pseudoscience. They are un-falsifiable because they simply describe how the specific systems they refer to work, they do not explain the causal relationships of the working components in a way that can be validated by alternative designs. Faraday's description of EM induction has two paradoxes... it is obviously not the truth. *Capacitors store their energy in the dielectric, not on the surface or within the conductors, you can easily transfer the energy from one capacitor to another by exchanging the dielectric of a charged capacitor with an uncharged one. *Electrical theory is specifically designed to conceal the truth about natural energy and the simple model of reality that is truth. *Advanced physicists admit Ether is real, they call it by the alchemical name: quintessence. But, they are careful to maintain it is only theoretically accessible, not something you create and manipulate yourself, nor is it something you could replicate with mechanical means like Tesla or Pantone did... 19th-century tech for Tesla, plumbing parts for Pantone. Today you could most likely find what you need in any junkyard. It appears the civilization that built the pyramids had a way of doing it with organic materials, water, and stone. Something replicated with a Joe cell, using steel, a cork, and water with a 12-volt battery. Truth is available to all not blinded by the misinformation that sustains our society. Electricity is not a fundamental building block of anything that cannot be destroyed or created. Electricity is made of charge and magnetism. Therefore, to create or destroy it, one need only alter the mix... From this truth, you can do a word dance that maintains energy cannot be created or destroyed, but the truth is, electricity can be freely created or amplified given one or the other of its component parts. And you know how freely charge can be harvested, or magnetism manipulated... It's all just a question of how much you need, not what you have to destroy to collect it. The purpose of the nonsense you spout is to maintain social control among people who otherwise would not put up with each other. Sadly, this particular approach of no free energy will be the death of all life on the planet. It also affirms the need to be mean to each other... which is a self-sustaining activity.. so, if you insist that free energy is not possible, you have to make sure you get enough by limiting access to others... if it were free, then your wealth would be worthless... and anyone could ignore you... if you weren't nice. You see, being a pirate works when there are limitations, but it is a choice, an adaptation. It is not who we are. Wilhelm Reich discovered the cure to that adaptation, so they killed him and burned his 30 years of research. A lot of energy goes into maintaining the status quo... that is what societies always try to do. But, without the foundation of truth, they all have failed...as will ours. You are the descendant of two genetic bottlenecks... that shows our world population has been reduced to about 5,000 people twice, there is no telling how many billions have not survived in the past. Was it through our own hand or just the natural changes our planet goes through on a cyclical basis? Without mastery of reality, it won't really matter which, will it? Do you really think there is any truth to global warming by man's production of CO2? It's just another pirate ploy to limit those who can have what they need. Meanwhile, nature is collapsing the geomagnetic field which will bring a whole avalanche of death-dealing disasters. Something we only have legends from around the world remaining. The truth is the power company steals from you. If you try to stop them you will go to jail, or be killed. You got that part right. Your only chance is to be a better pirate. But, our days are limited, nature is playing a different game. Between our own actions or natural causes that we deny, we will collectively discover reality bites. Party on dude, and be good to one another.

[@cynthiaayers7696]

@@mundymorningreport3137 well said. Sure you don't want to run for president?😊

[@borisjohnson1944]

@@mundymorningreport3137 LOL at your view of Maxwell's equations. Everything electrical works because they are correct. Also SR wouldn't be a good description if Maxwell was wrong. Didn't bother with the rest if this bit of trip is any guide.

[@mundymorningreport3137]

@@borisjohnson1944 Clearly you misread my statements. Good luck when reality bites. B

[@borisjohnson1944]

@@mundymorningreport3137 LOL, no I didn't. You haven't a clue.

[@tamaseduard5145]

👍👍💖🙏💖👍👍

[@TheMcdrewb]

👀👍🙏🖖

[@wolfgangboettcher3126]

Okay

[@siminedelcu2874]

😀😀😀😀😀