Testing Capacitors with ZOYI ZT-MD1, FNIRSI LCR=P1 and Other

  Рет қаралды 865

Michael Yates

Michael Yates

Күн бұрын

Пікірлер: 11
@peterskyes1267
@peterskyes1267 Ай бұрын
I have seen a few video's on the ZOYI by people that know what they are talking about and they seem very favourable towards it. These cheap testers are getting better and better
@marcusbridges1851
@marcusbridges1851 Ай бұрын
As long as these meters are in the ball park then they are handy to have. FNIRSI sell scopes and I thought this LCR meter would have faired out better, apparently its not that good by reviews
@jimsregaturntableshifijukebox
@jimsregaturntableshifijukebox Ай бұрын
Interesting stuff, thanks for posting Michael. Jim🏴󠁧󠁢󠁳󠁣󠁴󠁿🙂
@MichaelYates
@MichaelYates Ай бұрын
Thanks for watching Jim, all the best Michael
@chrisdado
@chrisdado Ай бұрын
If you want to test electrolytic capacitors thoroughly you need to measure three things, capacitance value, ESR, and leakage vs operating voltage. None of these meters measure leakage, you can have a nominal value cap with low ESR and still have a bad cap if its leaky (how detrimental this is depends on how it is being used in the circuit). The Zoyi is fine for capacitance value and ESR. There are some simple diy leakage testers you can build for low voltage caps. If you want to test high voltage caps I suggest you consider buying one.
@aransmitch
@aransmitch 8 күн бұрын
ZOYI ZT-MD1, after updating, the device cannot be turned on. What should I do?
@MichaelYates
@MichaelYates 8 күн бұрын
Mine updated ok. I would get in touch with manafacture, there might be a way to reset device
@mauanderuk
@mauanderuk Ай бұрын
ZOYI is the best here the others are poor and I would not trust them, the ZOYI has changable frequency. However I would recomend Peak Atlas ESR70 this is made in the UK or a capacitor wizard made in the USA.
@MichaelYates
@MichaelYates Ай бұрын
Thanks for the info, I did look at the Atlas and if I was going to do a lot more recaps I would have proberly would have went for that one its around £85. But I may just recap one more amp now and that will be it I think.
@painlesswiring5453
@painlesswiring5453 Ай бұрын
you don't know how to use the fnirsi,, the first press is for power on and the second is for testing...
@MichaelYates
@MichaelYates Ай бұрын
Ahh thanks for the heads up on the fnirsi
Китайские тестеры компонентов - какой выбрать?
11:14
Заметки Ардуинщика
Рет қаралды 322 М.
Хаги Ваги говорит разными голосами
0:22
Фани Хани
Рет қаралды 2,2 МЛН
КОНЦЕРТЫ:  2 сезон | 1 выпуск | Камызяки
46:36
ТНТ Смотри еще!
Рет қаралды 3,7 МЛН
I made my own Capacitor at CHEMI-CON!
20:50
DENKI OTAKU
Рет қаралды 13 М.
ZOTEK ZOYI ZT-MD1 LCR Tweezers Review/Teardown
21:22
Kerry Wong
Рет қаралды 9 М.
ZOYI ZT-703S - Firmware Update
3:59
Lockdown Electronics
Рет қаралды 2,2 М.
ZOYI ZT-MD1 LCR Tweezer Review & Teardown!
12:16
Darren Walker
Рет қаралды 4,6 М.
ZOYI  ZT-MD1 LCR metr
23:47
Marek OK2
Рет қаралды 9 М.
🔴 FNIRSI LCR-P1 Component Tester Review - No.1279
30:57
Defpom's Electronics Repair
Рет қаралды 23 М.
Хаги Ваги говорит разными голосами
0:22
Фани Хани
Рет қаралды 2,2 МЛН