Testing wireless ignition node module Chrysler Dodge Jeep ram plug connector

[@williamfry6087]

I watched this twice - a lot of good info here.

[@florenciomartinez3695]

Will that module keep the door locks from not unlocking locking with key fob

[@DanielNunes-zc1vb]

Do you have a video showing the voltage of all these wires? Mysteriously mine burned the module board. I would like to see if there is a wire that is sending current where it shouldn't be.

[@Jonathanraymen]

If you were to replace a non remote start win module for a remote start one, would that allow you to remote start the vehicle where you didn’t have that functionality previously?

[@chrisozouf4914]

No but there's a way to do it, look up alfaobd remote start

[@ShyRage1]

So what happens knowing that the win module has power because of lock and unlock on the key fobik work but you get a red blinking security light blinking on the dash and it prevents the vehicle from starting? Key fobiks are new and programmed to win module. Key fobik batteries are ok along with the new starter and battery

[@buiLderbob845]

I got the same thing did u ever figure it out

[@ShyRage1]

@@buiLderbob845 THe PCM had to be replaced.

[@chrishill264]

@@ShyRage1when you opened your truck did your alarms go off because it wasn’t deactivating the anti theft

[@ShyRage1]

@@chrishill264 no, i never had that issue.

[@phil8446]

Got a 2010 dodge grand caravan sometimes when driving it will shut off and go in accessorie mode is it my win module and can I just put a push start lmk thanks

[@StevieJayGamez]

My win module will not turn in my 2010 Dodge Challenger Rt. It’s frozen up and won’t fully returns My remote is broken. I was looking into ordering one and replacing it my self. Is it hard to reprogram a new remote to it?

[@ken1449]

My problem is doors sometimes dont unlock with fob and media screen stays on when key taken out and sometimes does crank but then work later? Is this the win, 2009 jeep g c

[@richardt875]

2014 Ram 1500 3.6L pentastar VVT Sometimes starts, Sometimes doesn't (intermittent,) the truck won't start unless I get that ding ding ding sound first. The Fob is in bad shape. Should I take a chance and get a new fob before buying a new Win?

[@AutoTechElectronic]

The fobik remote does not need a battery to start truck. Battery is only needed to lock and unlock doors remotely. Your issue is most likely the rfhub receiver. Text me to give you more troubleshootibg tipo 830-374-6845

[@rodger6940]

Hey brother, I have a 2010 journey it used to crank no start after some testing that I was doing now it doesn't crank, does nothing when I turn the key to the start position everything is normal except for the no crank no start and tge security light flashing on and off the remote works locks and unlocks horn sound good

[@mfloyd8271]

Checked starter by jumping terminal at relay starter works every time relay test good also the key fob works but the 2014 Ram 1500 will not turn over until the fob is turned sometimes 20 times

[@a.l.fairclothii6424]

got a 2019 Ram 1500 Classic. Truck ran fine yesterday, got in it this morning and I've got no dash lights, no radio and no ac controls, I do have my door open symbol and mileage. Is this the WIN or something else

[@AutoTechElectronic]

@a.l.fairclothii6424 Classic Rams do not have a WIN. It is an ignition switch. Most likely you need a new rfhub. Here are the replacement kits. autotechelectronic.com/rf-hub-kits/

[@haynlaskan9668]

for that win module, where do those wires go? to the rf hub? im looking for an ignition wire acc etc to install a viper remote start.

[@AutoTechElectronic]

You need to call their tech support

[@estebantirado3934]

Quick question my 2008 magnum is having that same problem as ur video. But the alarm doesnt work, windows dont work. But seats do. Only thing that lights up on the dashboard is a red dot and when you open the doors . The door logo comes on. Thats all that lights on the dashboard. Im going to probe the win . Today but does this sound like I need a new win?

[@AutoTechElectronic]

Yes, do the door locks still lock and unlock from Fobik remote?

[@estebantirado3934]

@@AutoTechElectronic no nothing works there is a red light that turns on only when i try to start it. Only thing that is on is the door open light.

[@civiceggable]

Geez all of the searching I have done and finally found an explanation of why my van doesn't start, the prnd lights do not light up. And my red security light is always blinking. I think I will upgrade to a 3rd generation win module. Should I buy one with a key or no just the box and a new unprogrammed key and have a locksmith program every thing for me? Thanks in advance, and for all the helpful information.

[@AutoTechElectronic]

When you purchase the win lit from us you get the win, 2 fobik remotes, 3 years warranty with no mileage limitation everything programmed to your vin. Plug and Play. Purchase at autotechelectronic.com or call 956-508-3450

[@john2648]

im hoping you can help me i have a 2008 dodge ram 1500 4.7 randomly wont start cranks but will not turn over (start) lights on dash work remote key also works could it be this module if so do you sell them

[@AutoTechElectronic]

Did you already check the fuel pump and fuel pressure?

[@cravingsunleashed4880]

So I have a guy that called me saying his windows were half way down and the truck wouldn’t start…. The remote part doesn’t work . Is that a key issue or win module issue ? The truck actually started in the morning when he found the windows down but didn’t start in the afternoon

[@ayeshaf79]

hello been looking for video on win module just saw yours thank you, got a question i put my key in (key fob) 2008 dodge charger 6 cylinder i turn the key and only the red security light comes on. i use to take the key out and in a few times and it would work now it do not. could it be the module or key really need help

[@AutoTechElectronic]

Most likely is the win. Text us a picture of fob and win to 210-920-5819

[@206two604player]

2010 grand caravan and with key in and try to start it I get no dash lights and no start. the key fob will not lock or unlock the door. Any ideas. Thx

[@timkeyser3515]

I have an 06 Grand caravan that was running fine till yesterday. Parked it, and now I have NO power to lights/dash/locks/anything. Battery and cable to TIPM bus bar has 13.6V. Alternator + terminal shows 13.6V. Battery 3 months old. Where do I start? This thing died out in the woods, and a tow could be a bigger problem than the cost of bending over for a shop.

[@206two604player]

@@timkeyser3515 I replaced the battery in the key fob and that solved my issue.such a simple fix. I was overthinking the problem.good luck

[@lorettapeterson867]

i have a 2014 Jeep Grand cherokee , with 3 key fobs , 1 Brand new, 2 originals all 3 brand new batteries. my jeep doesn't detect any of them till multiple tries and will finally unlock vehicle , and or star. Always says key fob not detected. When it finally starts it will randomly say key fob left the car. Have to shut the Jeep down and and will continue to say no key fob detected till finally starts or alot of the time just does nothing. starter, alternator car battery all good. My mechanic says its the Wireless ignition Nod, would you say it is? Its bad, ready to bring to the dealership to get it replaced

[@frankgencarelli9592]

Hello, I have 2010 jeep grand Cherokee limited 5.7. Vehicle randomly cluster lights start flashing, wipers stop, A/C stops blowing cold but blower still blows, if I shut vehicle for a couple of minutes and restart its ok. Is it the win module?

[@izzy1271980]

Hello I have a 2013 town& country. I only have stating issues when the weather is below 40 degrees. The car will only crank, eventually she will turn on and usually I won’t have that problem again until the next cold day. I did replace that battery and the ambient air temp sensor. And also cleaned the throttle body.

[@brandonharvey7939]

The fuel pump relay is a common defect on these models and its actually not in the engine fuse box per se like every other vehicle ever made. Its underneath the fuse panel soldered onto a circuit board Chrysler calls the TIPM, which stands for "screw you give us more money". Its outrageously overpriced and so is the labor to have one put in but if you google it or youtube search it you'll find that some guys who are actually qualified to engineer motor vehicle electrical circuits have come up with some relatively cheap and relatively simple solutions to the problem that the toddlers and thieves at Chrysler created when they built these flimsy tanks. Cant say in 100% certain thats your problem but its very likely. Theres a way to temporarily bypass it by stealing power from the auxiliary circuit straight to the fuel pump when you turn key by using fused jumpers..... you can google that too. Good luck chief

[@denisehaley9271]

I have a 2010 dodge journey sxt, all dash lights work, radio, but will not start. Intermittently will crank for a split second, then nothing. I have to wiggle key in order for it to crank at all. Is this the WIN module?

[@AutoTechElectronic]

Yes that is the most common symptom. We have in stock the replacement kits on our site autotechelectronic.com

[@roni1976]

Got a 2008 limited Chrysler 300 and when u put the key in and turn it to start just the lights on the dash comes on and it don’t start! Won’t even try! I’m thinking it needs this new part! How much does it cost from ur website?

[@AutoTechElectronic]

Text the year make and model along with symptoms to 2109205819

[@clappedsix7302]

Can my pre existing fob be programmed to my new win module? (Already have a brand new gen 2 win)

[@AndriyMisuyrak]

Hello, (2010 Charger ) The car starts with fobik but non of the buttons lock/unlock/panic/trunk works on both of keyfobs. (and i changed the batteries) Is that WIN responsible for that licking unlcoking remotely or there are another box that is in charge to detect keyless locking signal ??? And if yes where it is located ?

[@AutoTechElectronic]

The WIN is the keyless entry receiver. Test the fobik remotes at Autozone. If they work, you need new WIN. If they do not work, you'll need 2 new Fobiks( very unlikely, unless the fobik remote are not OEM)

[@indianadiecast2044]

How do we inquire about symptoms? I’m pretty positive I have a bad win but I wanted to confirm somehow

[@AutoTechElectronic]

@indianadiecast2044 text 210-920-5819 7 days a week. Or cal 956-508-3450 Monday thru Friday. Include picture of fobik remote key, vin and symptoms

[@greenbeen_079]

I'm getting 2 volts across the green and brown stripe wire are those positive still looking for a diagram for the win and p0562

[@AutoTechElectronic]

What are the symptoms ? Are you able to lock and unlock doors with fobik remote?

[@greenbeen_079]

@@AutoTechElectronic yes I'm trying to find a perisitic drain and found a the white with the green and brown stripe with 2v now trying to figure its normal or not but also my o2, cat, and emissions are flashing but my code reader is telling me they are fine

[@JorgeContreras-co5gd]

My 2011 ram shuts off when driving. Dealer said it the win receiver. Replacement is $900. Does your come with new keys or do I have to reprogram the old ones

[@AutoTechElectronic]

You would need new Fobik remote keys. Our kit includes 2 Fobik remote keys and has 3 year warranty with no mileage limitation.

[@AutoTechElectronic]

Old keys cannot be reused

[@JorgeContreras-co5gd]

Are the new keys already programmed to the new Win Node?

[@AutoTechElectronic]

@@JorgeContreras-co5gd our kits come fully programmed to your VIN. Plug and play

[@troyimamura1649]

Hi, I have a 2011 Jeep Grand Cherokee Laredo 6 cyl and recently, my vehicle stopped cranking but I can still perform some functions on the key fob such as locking the doors etc. Please advise if you think I should replace the WIN module.

[@AutoTechElectronic]

Call our office with the vin for the jeep 956-508-3450

[@MikesSoftLemonade]

what ended up being the solution?

[@El-Armstrong]

When i turned on just ignition the gauges started working then went off for a sec then back to normal. Day later i get what feels like a misfire when i accelerated randomly. Day after that when idling it had one little dip. Ik my win modules not great cos it had problems shutting off when using the push start so i just use the key now. Think it could be win failing?

[@AutoTechElectronic]

You definitely need a new WIN. The engine misfiring that may be caused by a faulty PCM

[@El-Armstrong]

@@AutoTechElectronic thanks. how could i check pcm? I assumed it would all be related. No engine codes as of yet. Car ran perfectly today

[@AutoTechElectronic]

@El-Armstrong I suggest start with replacing the WIN. To decrease changes of other modules getting damaged because of a defective WIN

[@El-Armstrong]

@@AutoTechElectronic could a win cause misfires and or idling issues or anything? I was under the impression once u use the key instead of pushstart it kinda bypasses it? Faulty win can spread issues??

[@El-Armstrong]

@@AutoTechElectronic couple month ago i had a code for up and downstream o2 sensors on bank 1. Replaced them n was fine after. Could tht be related? Cos my 09 challenger only has 30k miles which seems low for them to go out

[@cinamarieiro3701]

Hi, I live in Canada. Do you ship parts here? Im having trouble with my starter. Its a 2011 dodge ram 1500. Right now nothing comes on. No lights on the dash and it won't start which is the more serious issue. I can use the remote to lock and unlock and the alarm. But thats it. I tried taking the ignition apart to clean out with electronic cleaner as well as air duster. It did not work. Any other suggestions? TY

[@AutoTechElectronic]

Yes, we to Canadá and the rest of the World. Call us 956-508-3450 or Text us 210-920-5819 to place order.

[@-mjthecatdogfan-]

I have a 2011 town and country I got the alternator fixed and the battery died and now it's stuck in security mode any other suggestion I changed the tipm as well? No start no crank.

[@AutoTechElectronic]

What is the theft light doind when you leave the key in RUN?

[@jennifermartinez8895]

Hello, I have a jeep grand cherokee 05 it runs and everything but there's times where the car will turn off on me or shake like if it wants to turn off in the middle of the street. And before I but either buy a computer or a win module I wanna see what you think it might really be

[@jennifermartinez8895]

It gives me code p1697

[@jennifermartinez8895]

I unplug the batter and the code didn't come back only two different codes

[@tonylandry8919]

Where can you purchase new win module

[@gerardblack-gv1rr]

Hi I have a 2012 Chrysler town and country. it started at first I would push the start button and get a key fob not detected on my dash so I would wiggle the fob then it would work then one day it stopped working So I replaced the battery in the key fob and now it does not work at all. I had to remove the push button and use the fob like a key to start it.

[@AutoTechElectronic]

This is the replacement kit you would need www.autotechelectronic.com/win-module-kits/2009-2012-dodge-chrysler-jeep-wireless-ignition-node-with-existing-push-to-start/keyless-go-remote-start/

[@mikek4640]

Have a question fob works no start new starter 2015 town and county power going to starter no light on back of win when key in any suggestions

[@AutoTechElectronic]

Does the radio turn ON or windows go down and up?

[@mikek4640]

@@AutoTechElectronic yes

[@AutoTechElectronic]

Test the starter relay, wiring and starter. kzbin.info/www/bejne/naWZYpmGbJeEgMU

[@mikek4640]

I swapped the relays around and it’s still not starting clacks no start

[@mikek4640]

New starter and it’s getting power

[@jamesaugustine3331]

I have a 2012 dodge grand caravan sxt, I get a badkey message and a red dot under the neutral. The fob still locks and unlocks. I installed new batteries in fobs and brand new battery under the hood. Thoughts?

[@AutoTechElectronic]

Text us a picture of the 2 fobik remotes front and back to 2109205819

[@mecanimex]

Amigo si tiene voltaje de 12 y tierra el módulo está bien? Por mi tablero no enciende pero ya cambié el modulo de la llave y sigue igual espero y me puedas ayudar gracias

[@alejandroguzman5290]

Buena noche, disculpa tengo un problema igual, cómo solucionaste el tuyo?

[@mecanimex]

@@alejandroguzman5290 buenas noches si lo solucioné en la parte lateral del asiento lado del chofer hay una tapa esa tapa agarra con la alfombra abajo van los cables ahí estaba el problema estaba trosado los cables

[@darrenbarnett8107]

My 2014 Dodge 1500 series Hemi will not read to keep up when I turn on ignition can you please help me

[@AutoTechElectronic]

Yes, text me vin and a picture of fobik key to 830-374-6845

[@elitecourse9448]

How is it, I have a Chrysler 2011 in the morning, the remote control does not open and close the car easily, and I keep trying many times until the central lock opens. I checked the remote bar, it reads 3.1V... what is the reason

[@AutoTechElectronic]

What about the panic? If you open the door, vehicle starts fine?

[@tonyrevelez6824]

Hey I have a question I when to program a new key fog but they tell me that the module wir was lock ..

[@cristianmaldonado5587]

Hello I have a 2014 dodge challenger Sxt so my key locks and unlocks the car but when I try starting the dash says “damaged key”(I replaced the key battery ) and the car won’t even crank and no lights on dash besides that message but the weird part is that sometimes I get lucky and it starts up but then when I turn it off it goes back to the same thing and I don’t know what could be the problem if it’s the win module or I need to reprogram my key

[@AutoTechElectronic]

It neither WIN or Prox remote. It sounds more like you need a new rfhub. We have replacement kits. Text us your VIN 830-374-6845

[@michellecampbell7854]

Hello I have a 2010 Chrysler Town and Country. We have changed the started and the battery and alternator is good. All my panel lights work and the fob locks and unlocks the doors. But it sometimes I have to turn the fob over in the switch 10 plus times for it to start. Does this sound like its the wireless ignition module?

[@amylawrence899]

Did you figure this out? I am having the exact same issues...

[@gotobed-3-8]

I am having the same exact issue

[@joseterrazas4120]

Que tal, mi modulo win suena cuando cambio freno y accionó la palanca que podra ser ?

[@panuck5524]

Ir my remote does work and my motor doesn’t crank basically the win module it’s bad? Am I right?

[@AutoTechElectronic]

You still need to eliminate the starter, starter relay, pcm, network issue from being the problem

[@joshuaedson3533]

I have a Chrysler 300 2008 and my key fob works fine and so does the win module. The doors lock unlock but it will not turn over, it just keeps cranking over and over. What else could be the problem?

[@AutoTechElectronic]

It could be that you are not getting fuel. Ck fuel pump, relay or power

[@omaradame4439]

Hey i have a 2008 jeep grand Cherokee limited and it doesn't start or crank there is no communication the dash board don't turn on but i can lock and unlock the car. What can it be

[@AutoTechElectronic]

Send us a picture of you win module to 210-920-5819

[@terrancehall9139]

Having issues with my Chrysler 300. Didn’t get response to a new key. Dashboard says damaged key

[@hemiboydee4280]

I have a 2006 charger rt with a solid red security light that comes on when it’s I the car won’t start unless I wait 20 min with the car off to start it then when it starts it only will stay on for a couple seconds then it shuts down again then the red security light comes back on please help

[@AutoTechElectronic]

Check that the PCM I working

[@napalmloveskids]

I think my WIN is a 3rd gen. I have a 2015 Ram 2500 Cummins that wont crank the starter. I tried switching the starter, relays, got the batteries load tested, cleaned the battery cables and the ground behind the starter. I've tried wiggling the key, tapping on the WIN box, I've tried everything.

[@AutoTechElectronic]

Is the rfhub call 956-508-3450 to orfer

[@brandonharvey7939]

Did you try connecting a voltmeter to the solenoid signal terminal and seeing if you were getting signal from the switch. If not, follow the rabbit down the hole until you find the issue

[@King80s]

Question what if it’s sometime work and some time it doesn’t

[@louisgonzales7580]

My issue is off a 2014 Dodge Ram 4x4 5.7 I parked it and now it doesn’t do anything no lights in the cluster no movement on gauges radio doesn’t turn on , fob doesn’t lock or unlock doors.. I push the brake lights and nothing.. but head lights do turn on . No signal lights aswell.. Help me , could it be the key ? But the lights don’t turn on in the cluster when I turn lights on aswell..

[@AutoTechElectronic]

Che k fuse 51. If ok check red and black power wires at rfhub and ignition switch.

[@dmichaels3]

My 2011 Grand cherokee will not start, both fobs had batteries replaced recently. What it does is remotes will not unlock or lock doors, engine will not turn over at all. All the dash says is press brake to start engine. Tried jumping without success, Tried removing push button and using key fob to start and it won’t and know key fob wont come out of ignition.

[@AutoTechElectronic]

Check the WCM fuse (ignition switch)

[@dmichaels3]

I checked the the all fuses and relays under the hood of my 2011 jeep grand cherokee. It was not starting or even turning over at all. All seemed ok. I removed a relay and reinstalled it turning it around. pulled a fuse and it was ok. After doing this everything started working again. CRAZY!

[@MikesSoftLemonade]

Its likely just a flash update you need. there is a TSB for it. The software in the WIN module locks up. Look up TSB 08-024-11 and see if it applies to your vehicle.

[@frankiealcazar994]

So I got a 2011 Jeep grand Cherokee and my battery died and I replace the battery and after that my keyless entry didn’t wanna work no more It kept showing damage key when my keyless entry was working perfectly fine but if I put the key in removing the pushbutton it works perfectly fine what can I be then

[@AutoTechElectronic]

Which battery? Keyless entry or jeep?

[@codymt4804]

How about if the key starts the car but does not lock or unlock the vehicle. 2005 Jeep grand cherokee. It has an ignition switch and a wireless control module. Thanks.

[@AutoTechElectronic]

text me a picture of your remote headed key to 8303746845. a picture of the circuit board inside (front and back) We have various solutions for you.

[@codymt4804]

I have reset the wireless control module two ways. 1, by disconnected the negative terminal. 2, by removing the fuses for a few minutes and then putting them back in. I could hear it reset. Still not working. I think whomever had the jeep before me installed a new ignition switch. The key that starts the vehicle does unlock the door so it is the same cut. The only thing i can think of is replacing the wireless control module, taking it to a dealer, have them pull the personal identification number (PIN) from the power control module (PCM) and sync the new WCM. Thoughts? Circuit board/Fuse box www.wkjeeps.com/wk_fuses.htm Key www.aliexpress.com/item/Replacement-Car-Keys-Fit-For-Keyless-Entry-Uncut-Key-Fob-Remote-For-2005-Jeep-Grand-Cherokee/32803478601.html

[@josegonzalez1891]

Change the first fuse

[@olakunleabbey2203]

My Chrysler dodge 2010 is complaining bad key on the speed clock.What do I do??

[@johnortega9527]

I have a 2016 Town and country when I try to turn the key the lights come on but it will not turn over

[@AutoTechElectronic]

You'll need to check for a red security light on your cluster. If that light is on, then it would either be caused by the WIN module, or the key itself being the problem. If the security light does NOT come on, then it could be something wrong with your starter, or the starter relay, and there would still be a chance it could be your WIN module. To rule out the starter, you can use a paper clip on the starter relay to jump the starter to ensure that it functions. You can always call our office so that we can review everything in detail with you at 956-508-3450.

[@NobodyAskedForThis]

I have battery voltage at the run terminal in the run position. How does the WIN signal the start position? The wiring diagram doesn't show how the WIN signals the start position.

[@AutoTechElectronic]

NothingSpecial information is sent thru the network bus. What is the model? And what are the symptoms?

[@kingblack3378]

I'm not trying to tell how to do things but you checked the power without the key in ignition which Is okay but you also have to check if its still giving you constant 12V when you put the key in the ON position because sometimes the win can give 12v but as soon as you put the key in the On position the voltage goes flat 0. That will also tell you the win is bad because if the win isn't feeding the PCM then PCM will not feed the fuel pump or the starter which will cause a no start

[@BadWeatherfreak]

How do I reprogram the keyfob?

[@fernandoHernandez-tl3bo]

I have a 2012 ram 1500 laramie. Been having issues with keyfob buttons not working all the time. I decided to purchase a new keyfob and programmed. It worked all day. But at night. The buttons where not responding. The next morning the keyfob would not turn truck on. Kept saying damaged key. So nothing works again. My spare key still turns truck on. But buttons wont work. I replaced battery. But nothing

[@AutoTechElectronic]

Just program a New original oem fobik remote and you shiuld not have a problem.

[@fernandoHernandez-tl3bo]

@@AutoTechElectronic yeah i did that yesterday. It worked all day. But then it stopped working at night. Then in the morning. It wouldn't start my truck

[@romerogrady7195]

Truck won't start, I remove ECM and truck locks started working on fob. I was even able to start truck, but then I got a thunder bolt on dash so I turned it off. After that it wouldn't start again. I don't know if it's the ECM or the WIN.

[@AutoTechElectronic]

Most likely the pcm kzbin.info/www/bejne/nV6Uk4SnYtOMl6c

[@alanjones5925]

I have a 2008 Dodge chargerwhere the win module key broke and I would have to play with it to get the car started and it just stopped I ordered two and bought two and they came in today I took the circuit board out of the Brooklyn and put it in the new one in wouldn't do anything but I took the spare when I have to have lived program and put it in there and it would turn the instrument cluster on but it wouldn't start the car cuz it's not program so can you tell me what I need to do in order to get either they all one running or get the new one program

[@EdgarBustamante-b5x]

Good morning Tengo un 2015 tonw and contry la llave se queda pegada y no prende

[@greendays1102]

I have a 2009 grand caravan car sometimes doesn't start and I have to disconnect the battery for about 10mins after that I hear a sort of computer noise is that the win module?

[@AutoTechElectronic]

describe the symptoms, please

[@mateoavila21]

I have a 2010 Chrysler 300, my car won’t start anymore thought the key was dead replaced the batteries and still nothing no crank nothing. Is this the problem I’m having?

[@AutoTechElectronic]

Dores the cluster light up? Windows go down and radio turn ON?

[@SM-tq3hn]

I have a 2014 ram hemi. When I put the key fob in nothing happens. No lights on the dash no radio and won’t start. Doesn’t even make a noise. New fob or win or both ?

[@AutoTechElectronic]

Call or text us 830-374-6845

[@roelnavarro88]

What's going on Walton Guerrero just saw your you tube video had a question for a 2012 caravan about the win module

[@AutoTechElectronic]

Text me your question to 2109205819

[@JohnAReese]

Mine keeps saying bad key bad key and when I push it in with a little force it will crank, so I’ve been leaving the key in , I replaced the key and the new key worked and hen it said it was a bad key too !

[@AutoTechElectronic]

You need a new WIN module kit with 2 Fobik $599.95 plug and play. No need for the dealership. 3 years warranty with no mileage limitation. Autotechelectronic.com

[@JohnAReese]

Call me 4045838111

[@ezequelmarin7954]

Does the win module on a 2009 ram control the speed sensor or actual gauge on the dash? I know for sure i need the key module... But just wondering

[@AutoTechElectronic]

No it does not

[@ezequelmarin7954]

@@AutoTechElectronic how soon could i get a module if i order it today?

[@AutoTechElectronic]

@@ezequelmarin7954 we have UPS overnight $60 you can have it Friday or Priority mail 3-4 days

[@ezequelmarin7954]

@@AutoTechElectronic just placed my order today at 2 pm, 4/7/2019.... i paid for the overnight 60$.... any idea on when it should arrive? thanks in advance!

[@paulszeles1828]

@@ezequelmarin7954 overnight

[@israelinfante3055]

Tengo un problema con una caravan 2008 no gira la llave

[@AutoTechElectronic]

Llameme al 8303746845

[@kevinbatistta491]

Good morning! So I was driving the other day and my car just stalled... When I try to start it again I noticed that the security light was flashing and even though my car was in park.. the indicator light said I was in reverse.. I also noticed at this time that when I stepped on the break I did not hear the shifter interlock clicking anymore... When I bought the vehicle the remotes were never working but I've never had a problem starting it until recently! Right now it starts no problem but last time I drove it for a few miles I'll end up getting stuck with it again... I'm not sure if there is a way to bypass the ignition and just put switches in and a little starter button? I'm so desperate right now and I don't have the money to spend chasing this ghost... Any information you have or suggestions is greatly appreciated... Thank you and have a great weekend

[@AutoTechElectronic]

When the theft light flashes after a stall, the problem nostalgia likely cause by a lose wire going to pcm or faulty pcm

[@kevinbatistta491]

@@AutoTechElectronic interesting... Thanks.. would it disable the brake/shift lockout and make dash appear in reverse?

[@homeroluevano7985]

Hello, i have a town and country 2008. I think that something is wrong with the WIN, the dash does not do anything, no lights on dash and no ignition. Do I have to replace the WIN?

[@blaccwood4763]

Homero Luevano my same issue right now

[@dannydyi]

My Chrysler wouldn't turn to the "off" position because my shifter button wouldn't click and therefore my win wasn't recognizing it was in park. I pulled the win fuse in the tipm and put it back in. I was able to turn my key all the way and remove it. Next time I tried to start it, -no power. -at all. Battery is good. Im not even getting headlights, door locks, nothing. Do you know if a bad win will affect headlights and door locks?

[@AutoTechElectronic]

What year and model Chrysler?

[@dannydyi]

@@AutoTechElectronic 2008 town and country...

[@dannydyi]

@@AutoTechElectronic kzbin.info/www/bejne/aZvFZ4ecnr-gndE -this is where im at...

[@orenthalsimpson]

www.nhtsa.gov/recalls

[@jasoncranman7284]

I have a question,intermittently the truck will crank and not start, it will also act as it has a weak battery or starter.i have tested the battery,starter,alternator .alll good .yet once in a while this happens. How do I fix this?

[@AutoTechElectronic]

Jason Cranman what is the year and model?

[@jasoncranman7284]

2007 dodge ram 1500.with a 5.7 liter hemi

[@AutoTechElectronic]

Jason Cranman are you getting any DTC codes in the PCM?

[@jasoncranman7284]

No codes

[@AutoTechElectronic]

Jason Cranman send me a text 830-374-6845 there is fuel and spark?

[@billybrewer739]

I got a charger it's a 08 it's not starting the key is like the one in the video it will unlock car and trunk but will not start only the door lights come on the dash nothing else radio will not come on but the head lights work

[@DavidPorter-qz5qz]

2011 Ram, the remote start stopped working. When you press the key fob, the door locks, the horn beeps once, the lights flash once, but no auto start. any ideas?

[@panuck5524]

I have the same problem, I Just found this video, I don’t know what to buy

[@steveellis1688]

Hi Interesting video . My issue is slightly different from everything else ive read here. My jeep starts and runs fine. However, it will not switch off once started. The only way to cut the engine once started is to pull a fuse and disconnect the negative battery terminal. There is also a loud buzzing sound coming from my WIN module, so I am wondering if that is damaged in some way ? But before I commit to buying a new one I thought I would ask the question here Thanks in advance

[@AutoTechElectronic]

What year and model? Which fuse?

[@steveellis1688]

@@AutoTechElectronic Hi, it is a Grand Cherokee ltd 3.0 year 2010. I am pulling a red 50 fuse from the far left hand side of the large fuse box under the bonnet

[@AutoTechElectronic]

@@steveellis1688 if you unplug the connector from the back of the WIN and vehicle turns OFF instead of removing the fuse. Then the problem is the WIN and you need to replace it with a new one

[@steveellis1688]

@@AutoTechElectronic Thank you. It does indeed turn the vehicle off. Does the item have to be an identical part number ? or will any similar one work as long as I get one with keys supplied ?

[@steveellis1688]

@@AutoTechElectronic What do you charge for a replacement item with keys ? Does the part number need to be the same or will any do the job as long as it fits physically ?

[@punkpollo4070]

Se necesita programar el modulo o solo funciona al instalarlo con la antigua llave ??

[@AutoTechElectronic]

que modelo y año es el vehiculo?

[@punkpollo4070]

Auto Tech Electronic. Es 2009 dodge charger 2.7

[@jonathanwhite7968]

Hello have 2010 chrysler 300 touring 3.5 turns over but no start only has spark for first first second been sitting in. My driveway for over half year its my sisters car driving me crazy

[@themrbony]

I have a big problem the key fob isn’t active the alarm or either way donk make work the lock and unlocked button including the panic button the battery is good at the key fob but buttons not working I put it in the key slot and turn the switch to on position and everything seems to be working fine all the lights on dashboard fuel pump working at turning the key to on position throttle body is moving at the same time when i turn the key to on. But the biggest problem when I turn the switch to start position nothing happens as many time i try nothing happens. I just listena click sound on the fuse box located at the trunk of the car next to the battery Also the red light on dashboard just turn on when i turn the key to in position but seconds later it go off thats mean it’s the keyfob is programmed. It could be the WIN

[@steelemarchuk6254]

Not true. I removed the win and remote still worked. So how do I know if this is my issue. I have power to it and only 4 wires 2014 3500

[@AutoTechElectronic]

You do not have a WIN, so to reaffirm, 2009 thru 2012 rams have WIN and if you unplug it should turn off. NOW, 2013 thru 2022 classic RAMs you would need to unplug the Rfhub for truck to turn OFF

[@Willperez1974]

hello...i have a 11 town n country remote start from factory n i got key damage message n no start..pulled the little plug out inserted key fob and it started....is my problem the win module or something other....what do i look for

[@AutoTechElectronic]

will Perez text me 830-374-6845. With how many Fobik and if they still do passive entry from outside.

[@graysonswinson9389]

Hey man needing help before I call dealership I have a 2010 dodge charger sxt my fob stopped working a couple days ago but I was still able to start car my last fob none of buttons worked but still started car. Anyways I went to get a key fob battery and still not working but was able to start car got home parked it went to get in it maybe 8 hours later and no start tried both keys Lights on dash are on but won't start or crank I did hear a click when I was under hood and had someone turn key...I've checked all fuses and battery also the security light isn't on until I put the car in run position and it just blinks Any help would be appreciated

[@AutoTechElectronic]

What does the security light do?

[@graysonswinson9389]

@@AutoTechElectronic it blinks in in the on position locksmith came out today and said that my keys are good and still programmed to the car but I have no unlock lock or panic button on fob

[@AutoTechElectronic]

@@graysonswinson9389 remove the WIN and text me picture 830-374-6845. . Mosty likely you need new WIN

[@alexbomkamp3403]

I can’t figure out what is going on with my 2011 Chrysler town and country. When I put my key fob in it cranks but doesn’t doesn’t start iv been having to cycle the key over and over again and I can get it to start eventually sometimes having to tap on the gas to get it too idle. When it first started happening my remote start worked fine but as soon as I put the key fob in it shut down now neither is working all it does is crank and won’t turn over. No check engine lights on. Unlock and lock buttons work. Can somebody help before I decide to buy a 900 dollar win module kit ???

[@MegaMaxmontana]

My best regards and thanks for your videos well explained. I would like to explain to you about a problem that I had this morning with my GCL 2011 I went to start the car i inserted the key to turn on the car and appeared in the deshboard screen message saying "dameged key "and the car is totally dead dead i tried with the other key the answer it, I disconnect the positive cable from the battery I left it for 5 minutes I returned to connect the battery and instantly the dashboard and the dvd screen turned on without connecting or pressing the key to start. what do you suggest my friend it could be the problem or what should I do? Thank you very much for your valuable time.

[@AutoTechElectronic]

Mr. goldstick call me or text me at 830-374-6845

[@billeyleefinneyjr.1868]

I have a 2012 dodge ram 1500 4x4 big horn and in cold weather its start coding out now nothing new battery in truck and key not getting power to win mod

[@sifuentes1985]

I have a chysler 300 2008 and the dash lights don't come on and does not turn on,it locks and opens hwo much for a win module to be referbished

[@AutoTechElectronic]

fernando sifuentes call me or text me to 830-374-6845

[@patlajoie]

Hi. I have a RAM 1500 2013 Outdoorsman. Had a non dealership garage try to program new keys as one original was not working and the other one was taking 20 sec holding the unlock button to unlock the doors. garage was not able to program them and was getting an error (truck) "antenna #4" which was a short to ground (B1A74-11 passive entry antenna 4 - circuit short to ground). Antenna 4 is at the Radio frequency hub level (RF HUB) I've been searching around for a diagram to physically locate this module inside my truck without any luck. the garage indicated it is behind my rear seat. Would you be able to let me know where I would be able to find this "box"? thanks

[@AutoTechElectronic]

We have a video showing you the location: kzbin.info/www/bejne/n4vYmH17bMtnkJI From what you've described, you have a faulty RF Hub. We can send you the RF Hub with Two Fobik remotes with 2 warranty for $499.95, already programmed and ready to go. You can give us a call at 956 508 3450 from 9:00AM to 6PM CST M-F.

[@Crystian7521]

i have 2016 Dodge Ram Diesel 2500 is the same problem i need reprogram key too

[@AutoTechElectronic]

Text us a picture of you current fobik remote, symptoms and year, make and model to 2109205819

[@macannnas]

Hermano k tal me gustan mucho tus videos.. Estoy tirado en la carretera... En este momento y no se si sera el key nod porke se me apago de repente.... Ya no tengo power... Cheke fuses conections.. Nose k hacer.... Ya le di ala llave muchas veces y nada... El remote sirve puedo lock y unlock.. Pero tengo las ventanas abajo y mucho Frio.. No puedo subir las no tengo power.. El dash solo aparece Luz en los dials y las millas y las puertas abiertas no mas information en. El main screen... Please help

[@AutoTechElectronic]

Call 956-508-3450 or Text 210-920-5819

[@cutweldngrind]

I just noticed you are from laredo. Can I stop by so you can confirm what I need for my Durango 2013.

[@AutoTechElectronic]

Yes you can stop by our shop at 1903 W Calton Road.

[@marcoam35]

@@AutoTechElectronic hey my 2010 dodge charger SXT will not start my horn, windows, radio, nor cigarette lighter not working my lights work and my cluster the only light comes on is red and the other light that shows on the cluster is the car when the door is open

[@karmatias11]

I have a 2010 dodge ram. I had two keys programmed and now none of my keys work, including the original. All 3 keys (org +2 new ones will start the truck, but truck dies 3 seconds later. All keyless functions work, including remote start. But as soon as i insert key, it dies. I am getting a few errors, including "u0236- lost communication with electronic steering column lock module" and "p0513- incorrect immobilizer key(immobilizer pending SAE j1930 approval)" please aby help would be awesome!

[@karmatias11]

@@francislaceese8552 I did. The win module was bad. It costed $900 for the dealership to replace and program.

[@obedchavira1165]

Owner of ram 2011 long horn eent to start the truck it unlocked but when i put the key in the ignotion and turned it all the ligths inside flashed and turned off And now my key is not working wont unlock or lock and there is no power to the cab nothing happens wen i turn the key battery is good what could it be?

[@AutoTechElectronic]

With a voltmeter, check that your fuses are good and have 12volts.

[@randyu8688]

2010 dodge ram 1500 says "damaged key" and doesn't turn on when I turn the key over. After I wiggle it and try and try all the lights on the dashboard finally turn on and the truck starts. What's going on 😐

[@AutoTechElectronic]

You need a new WIN module. We have the latest generation with 2 Fobik remotes programmed to your VIN plug and Play. 3 year warranty unlimited miles. Autotechelectronic.com

[@donovanchee9728]

I need a WIN module for a 2012 Dodge Ram 3500

[@alex86899]

amigo tengo una durango 2011 y el control no abre y cierra las puertas y no enciende con le boton de encendido.. pero si enciende metiendo la llave.. que podra ser?

[@AutoTechElectronic]

alex86899 revisa la batería puede ser eso, el control Fobik no sirve o está dañado el PEM module

[@alex86899]

Walton Guerrero gracias por su respuesta amigo, ya le cambie la bateria pero sigue igual, dice llave dañada en la pantalla.. lleve la llave con un cerrajero y me dicen que si manda señal.. aun asi puede ser que la llave este dañada??

[@FernandoSerratos1]

I hope you get this ok so my 2008 chrysler 300 worked one day then sat for a few weeks and the battery died I tried jumping it and it wouldn't jump so I got a new battery put it in and nothing works it won't start stater don't click radio don't work car won't get out of park the only thing that works is it'll unlock with the keys and the headlights work please help

[@kingfisherman1836]

fernando serratos I'm having the same problem right now except I shut my car off for 30 minutes and ran inside my house came outside and now it won't do anything but unlock and the lights will come on. no radio, horn, or any dash lights will come on & my windows are stuck down. checked my fuses and battery everything's good

[@billybrewer739]

Same here could really use some help

[@efraineltroquerodelaintere6445]

I need one for my 2008 dodge grand caravan

[@ajmobileautoelectricdallas7980]

Hola ordene node module con tu compañía pero la tricks todavía no prende . Hablé con la muchacha de tu compañía y dijo que ya no podía ser nada.cual sería mi segundo paso ?

[@AutoTechElectronic]

AJ Auto Electrical Repair llama a la oficina y pide hablar conmigo 956-508-3450

[@ourawesomeglobe6131]

Hi, I own a Dodge Ram 1500 year 2012. I've actually bought it from someone. And around 3 months back it started giving issues while starting in the morning or after office. But it used to start after 2 or 3 attempts back then. One morning It didn't start at all so I had to get the battery checked thinking it was a power issue. And yes it was the battery, although after I changed the battery, the problem did not go away. It gives me a problem starting up almost every morning now and sometimes it just turns off while I am driving it (However I do remember hitting a bump or bad road before it shutoff while driving). I was lookin at your video and wanted to know if it could be a WIN Module issue also the Key Fob does sometimes gives a problem while I try it but very rarely. The spare Key fob does not work at all.

[@AutoTechElectronic]

Waqas Rishi All these are symptoms of a 2 ND generation win module which are not repairable. You may purchase a new one with 2 new fobik remote keys $499.95 You may purchase at autotecheletronic.com. 2 year warranty

[@alexandergarcia7362]

My 2011 truck has the exact same issue. Did this fix your problem?

[@richardt875]

@@alexandergarcia7362 what fixed your problem Garcia?

[@josuelinares6945]

Same issue here with the same year truck did fixing the win module help?