How the Fuel Shutoff and Brake Solenoids Work on Bobcat machines

Explaining the 3 wire pull-hold solenoids found on Bobcat machines. These solenoids control the fuel shutoff on the engines and the brake lock on wheeled machines.
www.4tetradgro...
Tools We Use:
Hydraulic Cylinder Spanner amzn.to/3SAlHYw
Another Spanner Option amzn.to/3LR1JFb
Hydraulic Seal Clasper www.4tetradgro...
Hydraulic Seal Stretcher www.4tetradgro...
Injector Block Off Cap www.4tetradgro...
Bobcat Fuel Filter Bowl Wrench www.4tetradgro...
Wrench Extender amzn.to/3Yt2yvl
Spring Compressor Tool amzn.to/4fA030n
Hydraulic Seal Installation Kit amzn.to/3Yrs6sV
Hand Impact Tool amzn.to/3Sz0yOk
Common Rail Fuel Injector Test Kit amzn.to/4dasD6T
Injector Leak Back Test Kit amzn.to/46Btf3i
Electrical Supplies:
Milwaukee Solder Iron amzn.to/4dpp0cY
Tesa Harness Tape amzn.to/3SAdG60
X Fasten Harness Tape amzn.to/4cbItNA
Non-Insulated Terminals amzn.to/4dp18XH
Short / Open Tester Power Probe amzn.to/3WRdrpu
Power Probe Master Kit amzn.to/3WPETUR
Shop Supplies:
Gloveworks Nitrile Gloves amzn.to/3WADdwW
Oil Absorbent Pads amzn.to/4ckYq48
Absorbent Pads amzn.to/3WOX64P
Brake Cleaner (Its Really Good) amzn.to/3yse3sA

[@engenhariacbx3327]

Big Hug from Portugal! When someone is good on his work, then he dont have afraid of sharing knowledge

[@jimmeroniuk8266]

Can't wait for the next vid as my 863 brake wedge disappeared on the previous owners watch. Thanks for this vid and excellant explanation

[@michaeljbreault]

Awesome video. I found your KZbin channel when I was having issues with my bobcat, now I just watch your videos to gain knowledge for future troubleshooting. Thanks man

[@KO-ih1ld]

I currently have a 753 with a brake issue, I'm very interested in the next video - - thanks for making these video's

[@brianronaldson9253]

thanks to you almost everything on my s250 is working or not leaking. i can't wait for the lift pump video maybe it's the reason i loose prime after a week of not running it, and if you ever make a video about the bobtach valve block my bobcat will be 100%. you do a great job thanks again

[@marionstorm9004]

I have a 763 F series. Now I know what the click is when I turn the key! I've had a few instances of turning the key to the OFF position but the engine keeps running. The machine sometimes goes months without being used. WIth your explanation of how the solenoids work, I suspect my linkage is dry or dirty. Thanks so much for your maintenance tips and explanations! You have a very valuable channel for Bobcat owners and operators. 👍👍

[@jerrylager4834]

Thanks for these videos. Good concept explanation even when I'm not working a Bobcat machine.

[@lawrenceveinotte]

Thanks, yes it helps, my 7753 shut off solenoid became weak and did not work all the time, then the control got hot and melted, i removed it all and installed a cable shut off till i feel like fixing it, my brake has never worked, going to check that out today, thanks again.

[@victoryvisiontour]

Great explanation and demonstration of how the solenoids work. Thanks!

[@GoneUraling]

That would have really helped about 6 months ago! Still good info. What I'd like to know 1) I'm told by Bobcat my speed sensors need to be disabled, only they can do it, it's a simple program change, $400 please. Then 2) my hydraulics are getting "jumpy" at times, normally when lifting something heavy or if I'm trying to make small controlled slow moves. I'm told it could be a spring or o-ring somewhere in a valve body??. 2002 A300 here.

[@geraldlane1077]

Great explanation of how solenoids work, great video! Well-done! Thank you. GBL

[@gregoriotrujillo5706]

Thank you for your time

[@deanl2427]

Again, thank you for such an informative and educational video! Stay safe!

[@josephwright3597]

As always, great information. Probably the same way the fuel shut offs work on my old Cummins diesel.

[@jeffmaclean7700]

Thanks again for another great video,please keep them coming

[@jeraldhammond303]

Hello sir, I really appreciate how you simplify your video. Every dollar saved helps keep up the great job.

[@vger66]

Looks like business is good. That's great. Thanks for all the info.

[@Darenator1]

Great info! I didn't know there were two circuits.

[@rkelsey3341]

Could you also do a video on Bobcat nomenclature? I have 863 with the Deutz engine, but how does that fit in against a 763 or any of the others? I have figured out that "T" means a tracked vehicle while "S" is a skid steer, but all of the numbers make no sense at all. Thanks!

[@janhonza4770]

Very helpful. Thank you.

[@davidjackson4112]

Love your channel. Thank You !

[@libyafdr6799]

Thanks for all the info

[@frankrodriguez5202]

Great video... Very usefulness

[@MisterWhippy4win]

If I could, I have an electrical question about by T595. The cab accessory fuse keeps blowing. I have tried unhooking the back up camera, radio and power port, but doesnt help. It doesnt blow immediately. For the radio, it plays intermittently for a bit before it blows. I suspect a loose wire/rubbed wire, maybe even at the fuse panel. Can I just push out the connectors for the affected fuse from the panel for testing? Is there an easy way to get to the back of the fuse panel? (I unscrewed it, but there isnt enough clearance to look at the back)

[@kenh9508]

Thank you!

[@NoBody-ht1oh]

brilliant mate

[@zim7087]

Thanks for the info. I have a S175 and i never receive power to coil for the relay that powers the shut off solenoid. Hopeing its not the controller.

[@CTSCAPER]

Now I know the clicking noises when I turn the key on the 763C.

[@tommyk1073]

Good video..I enjoy learning about bobcat skidsteers. Question..could you do a video sometime on the proper way to tension the tracks? I usually roll the bucket down to pivot the machine back and shoot grease until I get about a 1/2” of slack at the roller..but I was never sure if that was the correct method..I don’t want too much stress on the bearings or rollers..thanks.

[@vvv7220]

07:25 Brake solenoid

[@juanmanuelarriaga7092]

Thanks for the videos they help alot I have a old 873 how I can know if the machine have a high flow hydraulics ? Thanks in advance

[@ganzosworld524]

Once the pull circuit is energized how does the switch over to the hold circuit happen with the relay

[@adolfoyalonso2955]

hi there my friend , i have a 773 skid and i install a new fuse relay harness and also a new fuel solenoid and nothing happen , if i get a tie wire and hold the solenoid in the machine works and operate them close key switch and run to the back to remove tie wire of the solenoid . were should i look thanks

[@Mattcolletti]

I have a t450 with error code m1607 says the brake solenoid. Hopefully that fixes it

[@321gidw]

Want to see if you had any insight on my been having it for a while I have a s150 bobcat and it would lock up at startup I thought maybe you had to warm up it would go away it would unlock after shutting it off a few times but it seems to be locked up now and won't let me do anything thought it was the brake solenoid so I jumped that out but the bucket is locked wanted to see if you have any ideas thank you

[@chikilinm5948]

I have a question sir. Can you tell me how can I find the fuse box in a bobcat 463 ? I hope you answer. Thank you

[@thunderstruckram]

I have an A220 ,, keyless control pad,, push the yellow button ,,glow plugs counter runs,,push green start button, i get nothing ,,tried to start machine at stater solenoid with external power,,turns over , but no fuel..is this because of fuel solenoid not being energized from control panel?

[@howardclarkeCYB]

Hi, Nice video, I have an S130 with a solenoid like like your S160, my voltage to the hold coil is only about 6v, I have the wiring diagram but it doesn't give indication what the voltage should be, do you know what it is on your s160 by any chance?? It seems low but if the voltage is coming from the computer is could be regulated down i guess..... still fault finding with a machine thats new to me with a few issues and some bush mechanic repairs i am trying to put back to factory spec

[@635suz7]

So the traction lock solenoid on a 06 t-190 would work the same?

[@eldonmoors-y5j]

the brake is not the problem it where the break hook upto the alumin casting is ground off

[@jeraldhammond303]

Hello can a main controller be hard wired around on a 2009 T320?

[@robertnellums6691]

I have a 2000 773 where part of the computer went bad so I set up a group of momentary and full time switches to turn on the added electric fuel pump start it and unlock the brake. I changed the fuel cut off to a mechanical one and now the hydraulics stopped working. Which ones of the solenoids in the spool valve will I need to energize to get the hyd working??

[@MHolt3573]

Is the IMV on the newer engines the fuel shut off?

[@orangesun3030]

What would likely cause the pull to be energized while the machine is running?

[@tetradgroup]

Bad relay or short to power

[@jamalelmaskaouy2753]

Sir, I have questions about the Bobcat 776 engine. I am a Bobcat driver. Please help me. The Bobcat engine is leaking oil. It is not from Lagog. Oil is coming out from under the engine..? Thank you

[@jamalelmaskaouy2753]

Sir, I have questions about the Bobcat engine. I am a Bobcat driver. Please help me. The Bobcat engine is leaking oil. It is not from Lagog. Oil is coming out from under the engine..? Thank you

[@justatool]

Good explanation, the brake solenoid seems to be a common Problem. Could this be a computer failure? My 873 stards and shuts off just fine, but the brake just doesn't want to work. I appreciate your videos . Thanks from Salt Lake!

[@tetradgroup]

It could be a controller issue for sure. Thanks from Pleasant Grove.

[@Rprecision]

Are you still using the same email?

[@tetradgroup]

[e-mail]

[@frankcooper6911]

👍

[@rabbitflow1]

So if I’m good understand solenoid close fuels line or opening

[@Wanous-hv7zo]

I have a bobcat t870 2010 and put new final drive motors in with no speed sensors it originally had speed sensors and installed software update to make it work but it just shuts down when you try to drive. Its at a bobcat dealer they don’t know what to do with it

[@tetradgroup]

Does the pumps have swash plate sensors? You have to have one or the other.

[@Wanous-hv7zo]

I have more info it goes forward and backwards but wont turn it say swash is out of range but when he looks at the numbers its fine. What happened is pump went out bad metal in everything replaced everything. New pump new final drive motors all hydraulic valves cleaned and rebuilt all cylinders new hydraulic cooler everything hydraulic was replaced

[@garysmith6073]

Great video. I totally understand how these work but I am still having an issue with my S150 bought a new traction solenoid still getting a 15-03 code with six flashes of the traction lock light. I have power making it to the relay common terminal. If I short the terminals in the relay socket I get an immediate voltage drop in the system. If I ohm the contact going to the pull solenoid to ground I get .2 ohms. Seems right considering my print calls for .3 ohms on this part of the solenoid. a 12 volt circuit with .3 ohms should pull 40 amps. Any ideas?