The BEST Flysky receivers for Airplane or Quadcopter, FPV Drones (that I've used) - FS-iA6B, Fli14+

[@gozappa.]

is the fs-IA6 also compatible with quadcopers?

[@johnnickerson9037]

I found the crossovers to be the best for quads, I have at least 6 of them and no problems and they have RSSI

[@johnrush1634]

Do I need to take anything off of my existing tiny whoop

[@tcz7742]

The X6B is great for airplanes, too, if you use flight controllers. Great ranger for sub250 FPV.

[@Enderkruemel]

I use an fsia6b that i moddet to Display the voltage of the flight pack, also i depinned it(made it very small) , and also i use the ia6 as the Transmitter, but with modified Firmware, also i put in an 2s 5200mah liion pack from an Powerbank, it barely fits in there ,but i also needet to use 2 other voltage Regulators, the original ones can only work up to 6v and 2s voltage is higer. I also addet usb Charging and Balancing(also it is compatible with usb c PD), an raw Batterie Input/Output (for Powering screens, Goggles or some external Module like Crossfire,...) So i get about 5km range now without modding the antennas. (But thats maybe the next step) maybe i put on an extra Switch, it is also possible... If there are some questions about how to modify the Radio or reciver please ask me.

[@bipinmoharana464]

Bro, can you help me to acknoledge whether fsia6 receiver could bind with fsct6b tx..................?please.....🙏🙏🙏

[@johnrush1634]

I'm trying to connect my FlySky transmitter to my happymodel mobula 6 frsky version which receiver should I use For that and how should I go about installing that what else do I need do I just need a receiver

[@eduardonavarrosr.9548]

How about FLY SKY FS-T6 problem, my friend sold his fly sky FS-T6 just a week later it show a display, Warning for your safety, turn up all switches, and lower the throttle to continue, I have done the suggestion that it is a defective switch ,but I had already replace it and still the problem is there, Your valuable help is very important so I can enjoy plying too thank U for your technical support and tell me how can I pay U?. Ed from Philippine

[@artisticyeti22]

My crossover receiver stops receiving after 200 meters, what could be the issue?i use a radiomaster tx16s mark 2

[@TonyWheat]

Hi am rather new to this. I have a FLYSKY FS-I6S and would like to know if the FLi14+ will work with small to medium size drones?

[@RCwithAdam1]

Yes, That its what I've used before.

[@truth409]

Does anyone know how to stop the glitching between channels 1 and 2 with the fly sky I6 maybe just cleaning potentially it's so annoying watching the alien run jerk randomly thanks and advance guys

[@informative_walrus]

I wanted to get a receiver with a gyro, I thought the turnigy GT 5 was the same protocol. Any luck with non flysky receivers? Does flysky make a gyro receiver?

[@biketech27]

Will the fli14+ work on with fixed wing when paired up with a stabilizer gyro like the Byme A?

[@bricknball885]

I have bought a FLYSKY FS-IA10B and I tried to use it with my new eachine wizard v2. However when I select receiver mode to ppm in betaflight the motor one starts twitching and would not work. Motor works fine if I select another receiver type. What could cause this?

[@gregorydahl]

Im not sure but for a quad you use ibus reciever connection to a wizard flight controller . The reciever outputs one wire carrying all the channels signals on one wire of the ibus output plug and the other 2 wires are 5v and ground to power the reciever from the flight controller and drone battery .

[@jacksoncandy9027]

do you know if the FLi14+ receiver would work with the new Eachine wizard x220 V3?

[@RCwithAdam1]

I don't know the specs of the x220 v3, but this receiver should work with any modern flight controller.

[@HrDux]

Back when I was a kid I had Airtronics for planes/gliders and Ko Propo for my RC car. Do they even exist now? I guess Flysky isn't that old and crusty. I'm fairly new to the FPV hobby and getting back into RC. After watching a lot of videos, I just went with Crossfire. (ooo fancy 🎩) It costs more, but maybe it has saved me from a few hassles. That Flysky compatibility chart looks terrifying. Your videos are great. I'm looking to get my first 3D printer and I'm considering that Tronxy you reviewed. BTW, are you also in Virginia?

[@gregorydahl]

I built my first tyro 119 with flysky and you made all the flysky instructional videos . I should send a money donation . have those rx and 2 flysky tx's for when it gets to where we cannot arm because of remote i d Can you make a 3d printed cool looking fpv goggle for the $27 5.8ghz monitor ? You can be too busy .

[@mani-00]

dude the range of the fli14+ is around 150meters! and it failsafe so fast, i don't how someone in 22 can still recommend this techno for quads