The Best Gas Can Vent Just got Better!

Рет қаралды 5,927

Embark With Mark

Күн бұрын

Пікірлер: 40

@EmbarkWithMark 6 ай бұрын

Here's a link to the vent cap if you'd like to support the channel, thank you! (Affiliate) amzn.to/3Xt0mDL

@raincoast9010 6 ай бұрын

That's how a BOSS opens tamper proof packaging! RESPECT !!!

@EmbarkWithMark 6 ай бұрын

Can't be tamper proof if its shredded. lol

@dalehammond1704 2 ай бұрын

I just ordered these vent caps, thanks! I couldn't believe how cheap (low cost) they are. I spent $140+ bucks on (4) 5 gal. "EASY CANS" and the internal plastic screens must go and they all need vents. Next I need an extension for the too short spouts. Other than these things the cans were perfect. P.S. Now I know what I can use that chainsaw for I got for Christmas.

@adammeyer3659 5 ай бұрын

The whole reason I’m here watching this video is to see how it’s done before drilling into my rotopax! Haha. Thanks for the how to! Good to know that if my hole isn’t drilled perfectly (which I can never seem to do) that this will still seal up nicely. Though I would appreciate it if you try out your rotopax before me!

@EmbarkWithMark 5 ай бұрын

I'm in the same boat, most of my holes are good but I always seem to have one thats a little iffy... I think there is enough interest for me to drill into my rotopax. I'll try to get it done this weekend.

@bucsam1660 3 ай бұрын

I like the fact that you drilled the vent hole off to the side. I saw a vid earlier where the guy put the hole in the seam, and it leaked! Gonna order some, thanks.

@EmbarkWithMark 3 ай бұрын

Thank you!

@ScoutSniper3124 6 ай бұрын

When drilling into thin wall plastic I like to use a jobber (short) drill bit and small cutoff length of 1.5" board (2x2 or 2x4 works fine). You first drill a straight 90 degree hole in the wood so that just a 1/4" or so of the jobber bit sticks out. You can drill a small dimple exactly where you want the hole before using the wood. Then with the wood as a spacer drill your hole, because the wood won't let the bit grab and run up into the plastic you'll get a nice clean hole that won't need work afterwards. My 2 cent tip of the day.

@EmbarkWithMark 6 ай бұрын

Great tip! I shall try this on my next can. Assuming I can get some wood through the mouth lol. Sounds like this trick works for most very thin material.

@mattblvck6540 5 ай бұрын

Would love to see this tested on a rotopax. I have both the 2 gallon water and 4 gallon fuel.

@human1513 3 ай бұрын

A step drill works great.

@jeffryrichardson9105 6 ай бұрын

Yes you should try it! 👍🏽😀❤️🇺🇸

@EmbarkWithMark 6 ай бұрын

I think so too!

@AlpacoFilms 6 ай бұрын

I'm gonna get one those vents for sure!

@EmbarkWithMark 6 ай бұрын

They are sweet!

@project_poor_runner 6 ай бұрын

I wonder of that would work in my Rotopax cans? I already swapped over to the h20 spouts on them.

@EmbarkWithMark 6 ай бұрын

If we get enough interest, i'll sacrifice one of my Rotopax cans. The H20 spout works so much better right?

@SB-ic2kl Ай бұрын

Nice! What brand of pour spout are you using on those cans? Appears to be good quality....no leaks upside down! Amazing

@EmbarkWithMark Ай бұрын

I have a link in the description! Zero leaks while bouncing around in the back of the rigs when clearing trails or cutting firewood. So, i'd say it's a good brand.

@AlpacoFilms 6 ай бұрын

Do this to those Rotopax containers! Need to see this!

@EmbarkWithMark 6 ай бұрын

Thinking about it!

@terrynee4108 2 ай бұрын

Never take advice from someone with a bandaged finger. 😂 Just Kidding. Thanks for saving me time self learning.

@EmbarkWithMark 2 ай бұрын

ROFL!

@ScoutSniper3124 6 ай бұрын

Locking EPA fuel spout that spills fuel everywhere... yeah, that's about par for the course with the EPA.

@crazycoffee 6 ай бұрын

I find it funny how the "EPA caps" meant to stop fuel leaks and vapor escape does everything opposite. Just like everything else from alphabet gunk

@MrChasP 6 ай бұрын

L O V E the chain saw

@EmbarkWithMark 6 ай бұрын

Same!

@dmtycn 3 ай бұрын

I will choose the old one, haha.

@EmbarkWithMark 2 ай бұрын

They are both good!

@iban61 7 күн бұрын

Ramai yang tak perasan,mula mula dengan digitised lesen memandu/kenderaan,kemudian PADU,bila PADU gagal di tukar kepada Kad pengenalan digital semuanya pakai Data untuk berurusan,Kemudian 5G ,siapa yang dapat?..Perlu ingat Ananda krisnan (maxis) kerana apa?.Fikir fikirkan la.

@adctex 4 ай бұрын

Hey.... nice try... but... you are suppose to use a STEP bit, not a regular drill bit. You will get a much cleaner, rounder hole with the step bit. Also, you can use a METAL tire valve stem that is easily available at most local tire shops as the vent. You will need to remove the spring valve insert and make sure to drill the correct diameter hole in the plastic can.

@EmbarkWithMark 4 ай бұрын

Maybe… but the kit comes with a drill bit. So I used what everyone else is going to get with the kit. Zero leaks, even while bouncing down forest roads clearing trails for the summer.