THE BEST WAY TO GET STUCK BRASS OUT OF RELOADING DIE
Пікірлер: 76
@xycooking634 Жыл бұрын
Amazingly helpful for a new reloader. Thank you for showing a way to get brass unstuck without having to go out and buy even more equipment.
@blalolblalol3 жыл бұрын
Great method! I hope I'll never be in a stuck case situation again, but it's nice to know. Let me share how I removed a stuck case "tube" (the case head ripped out of the case!) from my sizing die: -grab a paper towel and shove it from the top of the die (where the decapping pin usually screws onto). -screw the die upside down on the press. -put a metal rod (I used a punch) where the shellholder would go. -use the leverage of the press to compress the paper towel which will in turn push out the case. -use oil and a pick to patiently rip and take the paper inside the die out.
@GShileikis3 жыл бұрын
Excellent video, quick & easy! Been reloading since the mid-70s and this is the best methods I've seen! Thanks again!
@SCVGun3 жыл бұрын
I’ve been reloading off and on for over 25 years. That’s pretty slick.
@KIMO3653 жыл бұрын
Pass on the love!
@kmorris180 Жыл бұрын
That's pretty trick. I have a 30-06 case that stuck yesterday. I'll definitely give this a shot. Thanks for posting this video.
@jimiandersonblackknight75542 жыл бұрын
Looks a lot easier than the way I’ve been doing it! Thank you very much for a very good video
@kingfatiusiii4744Ай бұрын
Dude this is such a brilliant solution, thanks so much! Hopefully I won’t lose my .45-70 shell lmao
@mrbrown34622 жыл бұрын
I have had 50 cal BMGs stuck in my sizing die and I was able to get the decapping pin out and made an adapter to screw into the decapping pin hole with a grease fitting brazed primer hole closed on casing and just pumped it full of grease and casing shot out of die. I now have grease fittings for all my dies and think they work slick.
@Lucastrujillo593 жыл бұрын
great video i have been reloading since 1992 first time i seen that move easy thanks
@KIMO3653 жыл бұрын
Ty hope that helps!
@devilscut75646 ай бұрын
thank you worked like a charm🎉 you got a new subscriber
@stevenfry34425 ай бұрын
Excellent video - thanks!
@cory87913 жыл бұрын
Great vid!!!! Thanks for sharing!!
@bubbadoolittle28122 жыл бұрын
Excellent information!
@JerryTip6 ай бұрын
Thank you for the tip!
@wemcal4 ай бұрын
Great video and great information
@stuartbracken50899 ай бұрын
Brilliant. Many thanks.
@richardkut39769 ай бұрын
Excellent, thank you.
@kevinpillsbury5291 Жыл бұрын
Awesome. Thank you
@SuperVorpalbunny Жыл бұрын
MANY AWSOME THANKS!!!!!!!!
@sandrasage346 Жыл бұрын
Excellent!!
@longshotdiedtired1582 Жыл бұрын
Great video I actually have all these tool laying around
@griffithk2 жыл бұрын
Great idea thanks
@antonkotov68532 жыл бұрын
Nice done. Thanks
@jeffcodog2 жыл бұрын
Awesome!!
@garyb3512 жыл бұрын
Thank you!
@Fireworxs2012 Жыл бұрын
*This might work for straight walled pistol cases, but it doesn't work for crap with bottle necked rifle cases*
@bradlock559 ай бұрын
God bless you brother
@NIghthorseGrows3 жыл бұрын
Oh this is way quicker than the other ways I have seen, thanks.
@AGeekNamedRoss2 жыл бұрын
Good stuff!
@stariadversesmalum46383 жыл бұрын
Most stuck cases I have dealt with, the dies “relief hole” gets clogged. Next time it happens I’m going to try and find a punch small enough to poke a hole through the brass. Idk if it will work or not. I’ve been using a metal dowel and a hammer in my vise. It works but it’s not a preferred method. As you could damage the threading eventually I would imagine.
@robertrivasarroyo11742 жыл бұрын
Very smart!
@Physics0722 жыл бұрын
I've used this technique a few times. Beats having to buy a tap, drill etc. If you can get vice grips on it will come out. Faster too.
@jamespuig48582 жыл бұрын
Genius! Worked on the first stuck case but not on the second. Any ideas?
@ShannonOddo3 жыл бұрын
Genius!
@goodboyringo9716 Жыл бұрын
Thanks for the tip but my case still wouldn't come out until I heated the die then the case came out. I'm not sure why my Hornady die started sticking the cases but I ordered a Redding die to replace it, we will see. I used it once before and it worked ok, then it began sticking the cases . So this is only an added tip to use heat on the die. I dig a case out once before and its no fun.
@nlanwebb Жыл бұрын
Lol same here tightened the nut just pushed the Grips off got out the torch and twisted it right out I've only had .556 get stuck before nothing else ever... Yet...
@shannonpayne4478 Жыл бұрын
Genius
@shanov77 ай бұрын
Спасибо👍
@donz8501Ай бұрын
Will rhis also work on 223? Fantastic trick!!!!
@curtislong19875 ай бұрын
👍👍
@leeburton183 жыл бұрын
Great instructional, however that wasn't a pipe wrench, that was channel lock pliers.
@KIMO3653 жыл бұрын
Crap...
@warren36656 ай бұрын
Probably works if the case isn’t all the way in the die and you can actually get a good bite with the vice grips.
@michaelthompson7570Ай бұрын
Brilliant shame I will forget when needed…….
@HypocriticYT3 жыл бұрын
I just put the case head in a vice enough to deform it and turn the die with a wrench that loosens the casing. Then I tap with a soft leather mallet the die rearwards to get it off the neck expander. Just screw the die back in and keep reloading.
@colinsmith46722 жыл бұрын
Wow I wish I found this two nights ago. Lee directions say to remove top nut as you did and pound de-capping pin with hammer to remove the brass. Tried that, pin bent, brass still stuck. Trying oil and your method next, but I suspect I damaged my die at this point.
@KIMO3652 жыл бұрын
Noooooo
@agbrown3082 жыл бұрын
Same thing just happened to me. I just don’t know what caused the stuck case in the first place and I’m afraid to have it happen again. Any ideas besides disassembly and cleaning and lots of lube?
@garylewis66313 жыл бұрын
Pretty slick, beats drilling and tapping.
@MegaRiffraff6 ай бұрын
👍🏻
@chrisfournier61444 ай бұрын
Straight walled for sure! Bottle neck? I don’t think so. Sadly when rifle cases get stuck I head over to the lathe.
@tonyzhu403 Жыл бұрын
Unfortunately, did not work with my 223 Remington Brass and RCBS FL Die. Maybe it works with straight walled cases. Not sure…
@longshotdiedtired1582 Жыл бұрын
Same here , I tried it with a RCBS that had a .223 case stuck and a Lyman with a stuck .308 case neither worked for me , I even bought a really good pair of Milwaukee vice grips just keeps stripping the brass but not moving at all
@jesseowens14925 ай бұрын
Fucking awesome and I'm a dummy for not thinking of it myself. ❤
@longshotdiedtired1582 Жыл бұрын
Tried this with with 2 different stick cases I couldn’t get either case unstuck just striped them out
@samdunlap5365 Жыл бұрын
How's that work with 300 win mag
@underhil76483 жыл бұрын
did not work for me
@HunterParkNZ3 жыл бұрын
This is going to save me from drilling through my decapping pin
@KIMO3653 жыл бұрын
Thumbs up!
@RedDawnCA7 ай бұрын
A lot easier than drilling and tapping.
@huntingdad10 ай бұрын
This method didn’t even come close to working for me. Only made it more difficult to get out later. I just bought the RCBS stuck case remover.
@milboltnut2 жыл бұрын
Shazam !!!!!
@craftsman89d922 жыл бұрын
Fucking genius I was gonna buy a new 1 🤣
@KIMO3652 жыл бұрын
Glad it helped
@maritessmercado793 жыл бұрын
Do u reload 50 Beowulf
@KIMO3653 жыл бұрын
Negative kinda expensive
@bradchirdaris21908 ай бұрын
“These 3 wrenches” WHAT? I see ONE wrench, 1 pair of vise grips and One pair of channel locks.
@jadesumsion4 ай бұрын
Ya this didn’t help me at all. I should have drilled and tapped. Instead I kept drilling now I think I’m out and should just buy a new one. Damn it
@peterweikel71232 жыл бұрын
Didn't work
@easydoz12 жыл бұрын
NOT ME EITHER. I even drilled and taped the primer whole with a sheet metal screw and used a series of washers and all it did is bow and strip rings of brass off the bottom
@caltick6 ай бұрын
I call bs. Nobody sticks a 9mm brass, they stick bottle necked rifle brass. This method may work but this example is shady.
@patrickvernacchio75404 ай бұрын
It works. Doesn’t matter if it’s stuck or just academic.
@Countrytime212 жыл бұрын
Brought a Dillon xl750 and on thr first day I got brass stuck in there 🥲🤦🏾♂️