I did this same swap on my '78 GMC. Three speed on the column to the TKO floor shift. It's a great trans. I see you have a video on making a shifter, I ended up just moving mine to the center plate on the transmission.
@Thecraig9096 жыл бұрын
Yea this was just cheaper so I just made what I had work
@jasonchilcote27846 жыл бұрын
Cut and weld the Hurst out further is all.
@shanekielty27436 жыл бұрын
Need a jam nut against that heim to keep the all thread from backing out
@eddierodriguez24726 жыл бұрын
if im not mistaken you should be able to unbolt and rotate your shifter housing 180º..
@paulchristopoulos6856 жыл бұрын
Don't forget to add a spring so that the rod wont fall out.
@Nah_jack4 жыл бұрын
Actually doing the same swap in an 74 f100.. this video helped me prepare for what I’m gonna have to do to install.. thanks
@larrybair80746 жыл бұрын
Hurst shifter looks good. Too bad you couldn’t find the one with more loop in the shaft.
@dreamingcode4 жыл бұрын
Looks great I love the bench seat though. I agree with you too thunderhead289 is a rockstar
@sergiocontreras8930Ай бұрын
I want to do a swap on my 70 with 3 on the tree transmission but I want this a budget friendly something that I can use same bell housing and flywheel
@greatvaluebleach90396 жыл бұрын
You tossed that water bottle like a champ
@fireman12946 жыл бұрын
Make an adapter bracket with a 30 degree bend in it. Just big enough to bolt to the shifter base and the linkage rod. This is a temp fix and when you go to your buckets you simply remove that bracket and bolt the shifter back to where you have it.
@robertchew81675 жыл бұрын
Cool stuff dude !!
@quietmale001016 жыл бұрын
you could go to a weld or machine shop with the existing shiftier and tell them your problem and have them build (plasma cut) a shiftier that will go around the bench seat im sure they have a 1/4 drop plate they can use
@jamieround20726 жыл бұрын
super cool job it all work's esp,. w/ all the parts u wanted toooo esp,. the Z bar......... & the way long all thread bar great job finally paying off........ the go-pro show's it all w/ the lite u had under the go-pro.......
@KC-lg7tx6 жыл бұрын
Benchseats > bucket seats.
@CraftwerksMC6 жыл бұрын
Love how you cut up the truck instead of just pulling off the shifter assembly. Great engineering. Can't wait to see how the other truck on the crown vic front end turns out.
@Petrol3606 жыл бұрын
Once you get driving if the clutch pedal is still to heavy and short of a throw you can mobe the rod further down the shift fork away from the transmission. This will gove less throw for the clutch (or a longer pedal push to the floor) it will also make the clutch lighter in doing so. Might make it a bit easier to daily drive. Glad it worked out! Make sure to all jam nuts and locktight to the all thread!!
@Thecraig9096 жыл бұрын
Thanks for the info! I’ll most likely go hydraulic soon anyways but this will do for now with some fine adjustment!
@TheFrameoff6 жыл бұрын
does the threaded rod screw in to the piece that engages the shifter fork . Iam liking the 5 speed idea should go good to my cleveland
@TheFrameoff6 жыл бұрын
I was thinking about a 5 speed and I wanted to stay with the mechanical clutch linkage and you just showed me how , cool . Build On
@shartne5 жыл бұрын
Is that the floor pan out of the rat turd truck said you was going to use it. It cleaned up good.
@Tomcaatt5 жыл бұрын
My 62 has a dump truck seat in it wich has a cut out in the middle for that very thing. And you’ve probly already taken care of it anyhoo.btw; that ceiling is very cool, although being a straight up confederate I’d have a battle flag , but we’re all American right , right !
@JohnWheels6 жыл бұрын
Nice, it’s coming together great!
@chadkalina12576 жыл бұрын
Looks cool cant wait to see the difference it makes in the way it drives
@DumbJeepBoy6 жыл бұрын
this is just a thought, but id recommend that you put some sort of a pedal stop in for your clutch so you dont push it too much past the end point on the pivot
@TargaWheels6 жыл бұрын
V-notch the front of the shift lever down low, bend and weld it, and you should clear that bench.
@gavinsermersheim39676 жыл бұрын
Good luck on your truck man I love your vids
@zachariahlow68726 жыл бұрын
You can install the shifter you have 180° from where it is now. There are 2 shift cups in there about 3-4 in apart.
@jerrymarkel15236 жыл бұрын
The cone that goes against the shift Fork where the adjustment nuts are you should try to find one that's threaded it's like 77 to 79 pickups had them. I had one come apart one night and lost the end had to drive home with no clutch.
@pvillehick676 жыл бұрын
Make sure you allow play before the fork engages. The throwout bearing won't live if it rides on the clutch.
@Logster1916 жыл бұрын
YES .. Can't wait to see it going down the road..
@fernandoalvarenga78376 жыл бұрын
Awesome job. Soon on the road again with nothing but smiles per mile
@FastaFuture6 жыл бұрын
The Clutch Linkage look like it is going to hit the Exhaust might be how you filmed at 7:10
@duffrednecks9306 жыл бұрын
that's sweet man
@jasonchilcote27846 жыл бұрын
BTW....congratulations!!! Awesome when all that hard work pays off.
@jamieround20726 жыл бұрын
so u going to hold it in all the lower gears to drive it a bit till u have the bucket seat's in.........????
@SkateSurfSnowFly2 жыл бұрын
I think the shifter can be moved rather than cut the floor. Any reason why shifter couldn’t be moved forward?
@RandomNamewrx6 жыл бұрын
Just a suggestion.. Instead of spending 150 on a bench seat shifter.. You could take a piece of metal, like a 4" by 4" and drill holes and move your shifter up far enough to have it drivable. I'm sure by now you're already putting your bucket seats in but hey. Just a suggestion. Love your work man
@kenrinck49166 жыл бұрын
Ashton Lawson That's the same thing I was going to suggest. I hope he reads this one. There should be something in his scrap metal pile that he could do that with. It would mean 2 more nuts and bolts, but it would be temporary. Have a good day.
@peterpower04956 жыл бұрын
Just a fore warning about the clutch fork, I recommend putting a return spring going from the engine cross member to the clutch fork. Because as you drive and everything breaks in. Your clutch rod may start rattling against the fork. Mine did after I finished my engine swap. just my two cents so you don't start chasing a noise around like me.
@ronspaeth66496 жыл бұрын
Don't buy another shifter, just get ahold of some 1/2" plate steel make it 2-3" long and bolt plate to bracket and shifter moving it forward. Put a boot cover over it and no one will notice. Once you get your buckets set-up, remove the steel plate.
@TheFrameoff6 жыл бұрын
Did the drive shaft need changing
@rjr42933 жыл бұрын
Is this the TKO?
@nicholasfreeman75166 жыл бұрын
Nice job Craig!
@NICKSSHOP6 жыл бұрын
nice job craig its looking great
@calvinhandley23736 жыл бұрын
From what I've seen you have the welding and fab skills to alter that shifter to fit. Just a matter of cutting the shift lever and welding in a curved piece. On the other hand you already have the bucket seats. You could just go ahead and put the buckets in. In any case congratulations on solving the problem with the clutch linkage instead of doing the cable or hydraulic route that you didn't want.
@jamieround20726 жыл бұрын
BE 4 U GET THE CLUTCH BROKE IN YOUR LEFT CALF & ALL THAT WILL BE BIGGER.....LOL WILL IT BE WORTH IT ALL..... HECK YEA FINALLY DRIVING IT ONCE U GET THE TINEY GLITCH WORKED OUT OF THE NEW SHIFTER.........LOL
@Fordf-td6wq5 жыл бұрын
why didnt you switch over to hydraulic clutch?
@jamieround20726 жыл бұрын
U KNOW WHAT BUD............ I'M RE-LIVING MY YOUNGER YRS,. WHILE WATCHING U ALL IN THE OLD ( MAT ER OR OR ) SORRY I 4 GOTTEN.... )....LOL
@jasondeloach30456 жыл бұрын
Nice job that looking really good Craig can't wait to see you drive it
@eanhartman95746 жыл бұрын
Awesome man I knew you could do it! Lovin the series keep it up!
@Laurennussen91625 жыл бұрын
do you have a part number for the bellhousing , I called American powertrain and they said they did not know the part number .
@joeschlotthauer8406 жыл бұрын
Buckets...
@chancewaddell1366 жыл бұрын
Awsome great job
@pmr4136 жыл бұрын
Loved the last clip at the strip!!! Great job with the trans.~Pat
@americanbullets4886 жыл бұрын
Nice finally got the transmission in mater. I also watched the new floor panels video and cracked up.
@Viktorrhansen6 жыл бұрын
Awesome can't wait to get my T56 in my firebird :D
@travisgarage66836 жыл бұрын
Now that's a true friend if u not paying him
@elbinhojoan5365 жыл бұрын
What's size from your axel shaft after that mod since trans to dif?
@ralphslipperz506 жыл бұрын
What happened to the chassis swap?
@Thecraig9096 жыл бұрын
I need to finish this first so it drives
@michaelskrhak65186 жыл бұрын
Hey you need a return spring on the clutch fork!!!
@jamesclark98006 жыл бұрын
make videos longer please
@forterierocks6 жыл бұрын
Get some Borla Atak mufflers you won't regret it they sound awesome!
@mikew31375 жыл бұрын
Craig, can you please share which clutch fork you're using and which throughout bearing? I am assuming the stock F100 clutch fork and the bearing from the clutch kit (maybe the foxbody type)?
@Thecraig9095 жыл бұрын
MIke W stock fork and bell housing so everything mounts the same as original. Just replaced the throwout bearing with a new one from oreillys.
@americanbullets4886 жыл бұрын
Good day Craig909 how are you dude?!
@mendezgarage64874 жыл бұрын
Hey I have a quick question I have a 68 ford f250. I have a 390 fe motor bore over 30 good power. I want to put a 3650 trans with it hold up. They sell adapter plates for it thank you like your truck man.
@brianpardee12816 жыл бұрын
Yee yee brother
@allentownsend88046 жыл бұрын
hell yeah brother great job 💯
@faith_love71476 жыл бұрын
Have you tried any other shift knobs ?
@KaiserBruh6 жыл бұрын
Like the video before it even starts just bc it's a Craig Ford vid
@americanbullets4886 жыл бұрын
Too freaking funny.
@TF79Swain6 жыл бұрын
Where did you manage to get the TKO used? Been having a heck of a time finding one used for my f100 project.
@Thecraig9096 жыл бұрын
It was the only one on Craigslist at the time. That’s where I got it
@TF79Swain6 жыл бұрын
Thecraig909 right on brother. Keep up the great videos. Awesome to see others in our generation still into the old stuff
@scarlett925842 жыл бұрын
Should have pulled the shifter and spun it 180 degrees, that would have moved it forward. Dont ask me how i know this. Lol
@danielh50846 жыл бұрын
I wanna build a bump side one day and put a 5 spd in it
@adambrown77416 жыл бұрын
Why not just go with a hydraulic set up?
@Coronet_shop6 жыл бұрын
Craig what about a pistol grip shifter??
@beau_lyman6 жыл бұрын
Hey craig, looks sweet bro, im the dude that talked to you on instagram about being in San Diego.
@pisibish61116 жыл бұрын
Dude, keep the bench seat!
@johnk21266 жыл бұрын
I am running a crown vic crossmember and having trouble with my zbar. Can you take a pic of something from the front of your zbar, like at the mount looking towards it. My zbar is at a weird angle trying to make sure it's right. Is your pretty much level?
@Thecraig9096 жыл бұрын
Yea I have photos of everything. Shoot me an email @ carrnaggeclassiccars@gmail.com I’ll send them to ya
@vaioskaliakoudas63886 жыл бұрын
Why don't you notch the center of the bench seat to clear the shifter rather than spend ~$500 for another aftermarket one that goes far away from the original place???
@Thecraig9096 жыл бұрын
You really can’t notch a seat without destroying it
@Coronet_shop6 жыл бұрын
Yaaaay
@k5savage886 жыл бұрын
If your getting rid of the seat any way just cut the seat 😂 and put some brown cloth on it
@motecalevol6 жыл бұрын
Just use first third and 5th!!
@greatvaluebleach90396 жыл бұрын
motecalevol then he did all of this work to have a fancy 3 speed
@motecalevol6 жыл бұрын
Yes. . .a fancy 3 speed WITHOUT REVERSE!!!!
@michaeldahl3546 жыл бұрын
It seems to me that you may end up having issues or an unhappy medium in pedal travel and play with that z bar. Hydro and fabbed to your stock pedal may be your only option.
@davidmullett23406 жыл бұрын
can't you put the shifter in the same location backwards?
@treylewis70366 жыл бұрын
I have a 1964 Ford Galaxie 500 2 door Fastback and it's a 3 spd on the column, but I'm converting in over to a C4 auto. question: what is the year range of a C4 Auto that I can use on my car just by bolting it right up to the car without a adapter plate needed?
@t-n-tdigger53846 жыл бұрын
Cant you cut a groove into the bench seat to give the shifter more room until you get the frames on the other seats and install them? I dont know if you are looking to sell the bench but it seems a quick temp fix. Awesome video. Thanks for sharing.
@somerandomness42856 жыл бұрын
It would be awesome to see u have a pistol grip shifter
@TheWolverine-rm2kr6 жыл бұрын
Imagine driving with three people in the truck lol
@danielbaca66296 жыл бұрын
Where did you get your steering wheel??
@keithw3726 жыл бұрын
are you going to put the piece you cut out of the floor for the shifter back in? looked like you didn't need to
@jimmydionne26996 жыл бұрын
why buy another shifter just heat and bend the one you have :) been there done that with a 1965 chevy 5 speed lock the handel in a vice and heat just above the bilt point itll be trial and error so bend a little at a time til its forward then you just need to go up a little higher and bend it back
@chevylandt.v6 жыл бұрын
Are you going to put the seat up for sale
@Coronet_shop6 жыл бұрын
Craig how much for the bench seat once you're done with it?? My grandpa can use one for his F-250 highboy he found after 27+ years.
@erickrangel74316 жыл бұрын
The Coronet Shop I think his instagram said $60 but dont quote me on that.
@yournamehere63656 жыл бұрын
Aviation snips are dead quiet in the still of the night ! Buy any chisels yet ?