the Fastest, Best Handling, and Lightest truck I've built

[@ronniejohnson317]

I think a 4.2 Vortex 6 cylinder would be a great choice. A monster turbo and the bottom end torque would be awesome.

[@TKTmon]

YES! Even the earliest variant of this engine would be fun in an s10 at stock levels, but of course LT would force feed it all the boost.

[@You_no_viking]

4.3. Vortech

[@shadowopsairman1583]

Would it fit though?

[@DaInfamous0ne]

​@jpetersontrx that's what came in it stock. The 4200 he referring to is a inline 6 out of the Trailblazer/Envoy.

[@You_no_viking]

@@DaInfamous0ne yea I looked into it I thought he made a typo I just figured 6 cyl Vortech 4.3 ya know ....my mistake

[@LawrenceTolman]

So what engine should we put into the new AWD S-10? I am thinking about a supercharged LS of some sort, but let me know your thoughts!

[@osrr6422]

Stroked 5.7 Vortec, aka a 383. Would be period correct. GM should've offered the 5.7 in them. If its an LS, what about a stroked 6.0?

[@Nanan00]

Turbo charged LS/LT with a 6l80, basically make it a V8 Syclone. Some 90's Astro vans also had the same AWD transfer case and front differential as the Syclone. I ran 4x C4 corvette front wheels on my S-10, the rear wheels had the tires scrubbing on the leaf springs without spacers.

[@Cuhh346]

Good ole 350 or a sbc gen 2 lt1 like the red one stacy davids had on trucks

[@c0c0asauce]

I vote for a stroked aluminum block LS breathing natural to keep weight off the nose and make it easier to work on. It would be a nice contrast to your other trucks.

[@maxxproductions7749]

4.3 with a marine intake and a small turbo.

[@veasnapeng1]

LT, it's about time you do something with an LT!

[@LawrenceTolman]

I agrree!

[@RoadWarrior77]

I agree, also. It would be cool to see a 5th gen block go into something................. on a budget!

[@BurnsjHi]

You and the Stay Tuned crew should race after. Tony’s Sike Clone is an awesome build.

[@garrycress3482]

Just happen to stumble across this video. Glad you found out that the ZR2 rear end has a different pinion length and angle. That info is valuable for the 2wd S10 I'm building.

[@JadXtreme]

As far as appearance mods are concerned... there are the Xtreme trucks which always looked awesome to me. Also they made a GMC Jimmy Envoy edition that had unique headlights and bumper cover

[@bobhill3941]

20 years ago, I watched an episode of TRUCKS! with Stacy David and Mel Fair and they took a S10 eXtreme extreme red with yellow stripes and installed an LS1.

[@DaInfamous0ne]

Yea and nobody can find one now because they're so sought after... which is why I kept my S10 front end.

[@lsxmatt]

Gotta go with a 6l80e if this all about acceleration. I finally managed to find a core for my Tahoe. Circle d makes a great kit for them!

[@bernie3075]

This channel is awesome. This is way better than anything on Netflix, hulu, amazon prime, etc. Thanks for all the great content.

[@oblivion._.8294]

That is a build i have been dreaming of doing for years. Glad someone is doing it.

[@thetoolman3]

When you hinted about this project, I speculated it'd be a Syclone clone. But with a V8, it'll be that much better. Look into the Xtreme body kit and the ZQ8 chassis braces, too. This will be epic!

[@danmitchell1665]

Your Orange truck inspired me to build either an S10 truck or Blazer (S10) with all wheel drive. The last two months I was researching info on what rear end and front end would survive a supercharged LS. This video answered that question! I can't wait to see the rest of the build. I love how clean and factory looking all your builds are, so I will be following this one closely!

[@ralladoastalamuerte]

Not going to lie, I’m exited about this build. Just wished it was done so I could see the final result. Haven’t seen a build in a min and really looking forward for the end product.

[@kalyndyck315]

Big single turbo 4.8 with heads/cam for some good rpm and linear power.

[@jordanvanderpool5503]

I think the LV3 would be a perfect candidate for this truck and they make decent power with a stock bottom end with a turbo. I’d like to see a new edge cyclone out of this. Plus you can make 700hp with that motor and keep it lighter than the LS/LT platform.

[@shadowopsairman1583]

Just find a LV1 which doesnt have stupid DOD to begin with.

[@jordanvanderpool5503]

@@shadowopsairman1583 can always delete it with a tune.

[@davidrohde7574]

Yes! This is the answer

[@jaredhuang2225]

Compact trucks are my favorite, looking forward to this.

[@coryfeldhege4527]

As stated a Vortec 4200 with a turbo would be killer. The RPM that can be pulled out of a built 4.2 is amazing. There is an article from quite a few years ago around the time they came out that a Trophy Truck team (Nelson Racing maybe?) had been playing with a built one and the comment that was made stated it sound like a swarm of pissed off hornets coming at you down the whoops section.

[@jamesstobinski6144]

Calvin Nelson (nivlac57) has pulled good power from the 4200.

[@silentbravo]

Has some Stay Tuned "Sike Clone" vibes. Excellent

[@jamescarter6318]

I really like the sound of the syclone. Such a unique 6 cylinder sound.

[@brendonsnover]

Super excited for this build! I'm not sure you will see this comment, or if anyone else has already stated it, but zr2 models have different fenders and bedsides that have a reworked wheel arch (larger arch) and a flange that sticks out to mount the flare. So the zr2 flares aren't a bolt on for your truck without some decent modification to the fenders and bedsides. I'm sure you are more than capable of doing so, but just wanted to give the heads up! If you change your mind on flares and want some s10 extreme fender flares I have a set I'd be happy to send you to help with the project! Thanks for the great content

[@aslacker]

What a coincidence that I was re watching COPO truck videos today !!

[@Joerelaxx]

I agree with everything back to stock but clear front market lens. Cool project. Refreshing to have a new build on the Chanel

[@Anthony_Pell]

Looking forward to this project as well.

[@petersimpson1734]

Hey LT, while I generally appreciate your desire to take a path less traveled for power plants, given your competition goals, IMO just go with an all aluminum LS........ either Turbo'd, Supercharged or a big inch NA something like a 454LS. REALLY LOOKING FORWARD TO THE BUILD!!!

[@jeremydoblinger3609]

Front end looks way better

[@212caboose]

This is LITERALLY the truck I dreamed of building back in 1999/2000. THANK YOU

[@teaguegearhart9851]

Ls sounds fun. This build has potential to be your best feat yet. You will love driving this thing.

[@justinsquires5998]

Definitely following this build.

[@stevepoythress4678]

OK LT I can contribute a lot, from first-hand experience - we LS-swapped a '00 ext cab S-10 and it came out fantastic, it was 2WD and we used a 5.3L w/ cam and built 4L60 from 4th-gen F-body, the entire swap in 3.5-day holiday weekend thrash, truck was 4.3L driving Friday afternoon, was LS-driving Monday afternoon. Truck went 13.0 first time out, and was completely unsuspecting until you started it and it sounded like a 4th gen Camaro (lol) and has been daily driven since 2007. Issues to plan ahead for, biggest challenge is headers - we used OE 4th-gen Fbody manifolds and with modification they worked, we also had to grind clearance on the rear upper control arms & mounts as the space constraint is the exhaust interfering with control arms; different engine mounts will help/hurt as different folks sit the motor higher/lower in the frame. Other issue is maintaining A/C, we had to pocket the frame rail for the compressor and get custom hoses made but it works terrific. We were able to read the OE wiring schematics and with a couple specific wire mods at the driver's firewall preserved all OE gauges and controls. PCM was 0411, I can't recall if it was P01 or P59 but the truck had a cable TB so I think it was P01. We used custom efans (I make low-profile efan assemblies) and using every clearance trick we knew we got it all to fit and look factory, the packaging was very tight like 1/4" between waterpump and cooling assembly but it all worked great. We were forced to relocate the battery from the engine compartment, that is where we chose to locate the CAI/filter. More: you ask about forced induction - in our build there was absolutely no way to use a blower, OE positive-displacement ones require significant hood bulge (looks waaay to aftermarket for me) and there is no accessory space for a centrifugal. We could have possibly made a large turbo fit mounted on the passenger manifold. I don't remember exactly, but I don't think there is enough room under the floor of the truck to fit twin turbos. Hint on the NVG-149: the gears and chain from the 2500HD transfer case fit (direct swap) and are 33% wider, this is what I did to my Silverado SS. Reply if you want pics and notes from the S-10 build.

[@ront2106]

Always love watching you make things work and moto" do it right the first time".. wish you were a Ford guy for those builds, but I will watch your content and videos!

[@goin200mph]

Looking forward to this build, LT!

[@kevinjennings4924]

Extended cab syclone!! I cant wait!!!

[@DaInfamous0ne]

Im so tuned into this because my S10 Blazer is basically the same as this, and This is exactly what I wanted... LS... awd.... fast and still have my 4 door S10 Blazer capabilities. And my blazer already has 3.73s front and back stock.

[@timhuwaldt3213]

Awesome. My project is a 97 S10 Blazer, and I did the same axle swap. Didn't have the problems with pinion angle/driveshaft length, though. Everything fit pretty nicely. Junkyard 5.3 would make me happy, since that's my choice. An L33 might be a cool option, since lightweight is kind of the them of the build.

[@codybradley287]

My thoughts on the pinion angle is the shorter wheelbase of the blazer. Its got the same drivetrain but short wheelbase. And just like mentioned, swaps right in a blazer.

[@brandonkelly5958]

Hey Lawrence, thanks for the build video. currently building my Silverado SS Awd of 7 years. look forward to the S-10 build. have a good day brotha🇺🇲 Tucson, Az

[@glenncarr2121]

Hey LT. It is so nice to see OEM parts instead of what ever the aftermarket is offering ! Everybody is pushing aftermarket and I don't think it looks as good as OEM and most of the time it is cheaply made in China or some other 3rd world country that knows nothing about our USA made and engineered vehicles ! Not to mention fit and Finnish , most of the time you have too alter the fitment of the part before you can install the part . Thank you for keeping it real .😊😊😊

[@Sergeantgrunt]

It was a sad day when you sold the COPO truck. That was by far the most exciting truck you had on the channel. I am however, looking forward to the S-10. I've wanted to make a newer Syclone for a long time.

[@genemcdonald4430]

Really looking forward to this build

[@ironbowtie]

I did a similar conversion in an S-10. I shortened a ZR2 rearend and used shorter axles made for an '94-'96 S-10 SS. I left the spring perch angle alone and used angled drop blocks to counter the ZR2's inclination. This all was far easier than trying to find a stock width, 8.5" rearend from an already limited production '94-'96 S-10 SS which allegedly only offered the 8.5" with 4.3 liter, 5 speed models. Caltracs were bolted on after.

[@KamronLsx]

Yes!!! I've built 3 ls s10's myself. Glad to see you are tackling it

[@NBrogdon45]

I had a super rare 97 extended cab S10 fully loaded Automatic 2WD 4.3 vortec with OEM factory grey and black LEATHER interior with the factory floor shifter and console. I've only seen one other one but it didn't have leather seats, just cloth. BTW this by far is going to be my favorite build on KZbin so far!

[@bobbymulwee7641]

Rad project and looking forward to watching the build

[@dadgarage7966]

Incredible all those Rock Auto/Dorman trim parts and lamps fit decently. Hopefully, the lamps won't fill up with water in a few weeks.

[@666silva666]

Perfect dime bag to start with!!!

[@PhantomOverload]

This build looks like it's going to be great. Love the S10 my favorite small truck. You pretty much got the exact version I want to get an extended cab with 4WD.

[@Fierofreak01]

I've done tha factory shifter console on multiple S10's and Sonoma's pickups as the pickups never really got them. The cool thing is, that the connectors are almost always already there in the factory harness (even in the pickup harness's). And that makes for a nice neat install that just works. The only thing you really need is the console shifter column, as it also has the connector needed to make the shift interlock work. Plus, it will tidy up your swap and make it look factory. If you get oa column from the junkyard, make sure it comes with a key so that you can swap the key cylinder over and not have to swap out the door locks. The other thing that will be needed is you need the VATS to be programmed and there's plenty of KZbin vids that show you how to accomplish that. The shifter cable is a direct replacement for the column one and is not an issue to install, with the exception of having to remove the carpet to access the cable grommet. Another neat thing is if your console is equipped with a tow/haul button, it will work with the factory PCM as the programming is already in the code. All it needs is a signal , which usually comes from the BCM.

[@samsanderson1685]

I've always like your OEM+ approach to your builds. Is there a S-10 Xtreme body kit in the future for this build?

[@billywillis4194]

Glad to see you doing this project . I have a 96 5.3 swapped s10 I'm about to do an all wheel drive conversion and cammed 6.0 swap to when I find a good frame .

[@stevenbrowningsr1144]

If you go with the same orange wrap as the CoPo truck the flares will look great on that one.

[@bobworthier7999]

Looking forward to this build

[@IDRIVEOLDCARS]

Thank goodness video lt. And it’s not cause you’re getting old I follow u because u build the way my mine tells me to build but my pockets just never agree. Can’t wait to see more of this. I see where you’re going with it all purpose build I guessing. Still hoping for the cateye body for the awd chassis build. Seen on the next one keep em coming. #samenamegang

[@bdtaylor1979]

I’m also a big fan of the factory lights vs aftermarket. My 07 Avalanche that I bought from a friend had aftermarket projector headlights installed and he gave me some led tail lights for it as well. I replaced the projectors with factory headlight housings and sold the projectors and also sold the led tail lights.

[@ItsDaJax]

Lights just depend for me. A lot of aftermarket projector lights are trash. Some stock lights are trash. There are times I'd rather make a set, than deal with the ugly aftermarket or factory lights.

[@randalltolman2368]

Daughter has an 02 s10, loves it same milage as yours, runs good goes good but as you know maine weather is eating away at it can't find another one , she loves that thing. I'm following

[@jeyweb4236]

With a narrow rear end you can fit some 10" wide rears. Stock bow tie up front but you have to paint it red!!

[@Jeff-mc4tw]

Love the 2nd gen s10! Have one myself. I dropped in a Sbc 350 built up. 4 linked the front end and am running 42” iroks. I’d say a drop in a ls and you’d still be surprised with the power of that by itself. Good luck on your build! I plan on watching and keeping up with your progress!

[@bradstanley116]

So excited to see an s10 build!

[@stlrsfan27]

Great video brother, Awesome little truck.im a big fan of the S-10's ,truck and blazer.i have a bone stock 2002 2 door S-10 blazer lowered just a tad .keep up the good work and I look forward to seeing what you do next with that nice truck. 🤠🇺🇸

[@2000S10V6]

I am so excited for this new build! I will tune in for all of it.

[@garywinkel1831]

Really looking forward to this build!

[@SLP2300]

A new rabbit hole! Excited to see this play out. 😂 LS7!

[@nicksedlak5416]

I am excited for this build. I bought a zr2 s10 with 50k miles a few months ago and i have been wanting to awd swap it. I can not wait to see what this thing will do!

[@wkjeeping9053]

You can get a v6 to sound great if you know how to. But it takes a twin turbo to do it. Those wheels are zr1 c4 corvette if I remember right.

[@LunchboxQ50]

Hell yeah, mini truck FTW. You can NEVER go wrong with an LS IMHO

[@TBGaels32]

This seems like an interesting build. I love the S-10 and blazers of this era. I’ve got a few blazers and would like to do the LS swap minus the AWD conversion and keeping the 4wd and do a Solid Axle Swap.

[@xozindustries7451]

I like the build, I’d love to do the same thing but get a crew cab S10 bed and swap it onto a regular cab S10, AWD with an aluminum LS or LT.

[@mf_explosive304]

1993 lt5. Such a great looking engine. Maybe a 3.8 turbo, last one a new 2.7 turbo would be cool. So many possibilities.

[@johnkropp3793]

Sick choice on the wheels, can't wait to see them all mounted up!! Great build LT

[@bryantbartlett6823]

So LT I'm not sure if someone has told you this already in the comments but you could get a ZR2 extended cab S10 drive shaft and it should bolt in with no modifications needed. Also the pinion angle difference is because the ZR2 come factory lifted 2-2.5 in. That is probably why the pinion angle is different. I love the real choice you have selected they're going to look awesome. I hope you were going to lower the truck down and an xtreme body kit would look to help out with that factory sports truck look you are trying to achieve. KEEP UP THE GREAT WORK LOVE THE CHANNEL THANKS

[@FastSS02]

I'm guessing the incorrect pinion angle is because he pulled the axle from a ZR2 Blazer instead of an extended cab ZR2 truck. The shorter wheelbase would require a different pinion angle.

[@pob_car]

If I had to recommend an unconventional engine swap, I’d say a vortec 4200 i6 or its 3500 i5 little brother. Seems fitting for the degree of oddball or untraditional swaps you like

[@LawrenceTolman]

I do love the sound of a 5 cylinder…

[@FastSS02]

I don't think there's enough firewall to core support room to fit either engine as they're longer than a V8.

[@rachalhollier5679]

eBay has the factory style replacement floor plates to bolt down to floor so you can use factory bolts to hold the center console in place correctly. Even bucket seat brackets to move seat back for tall people. If I can think of it, someone has already made it,lol. What a great project you have. That’s a bucket list truck you building for me,lol I’ll have to enjoy watching you build one instead. Looking forward to all the fun watching this S10 fly!! A tire slayer,hahahaha

[@PunishedBriggs]

Hell yeah, i have an S10 that i want to AWD swap but i will be going with the Vortec4200 Straight 6

[@GrandPitoVic]

The wheels look great!!!!!

[@thethrillofspeed]

Great build! Needs to have an aluminum LS. I would go with an LS3. Stick would be an added bonus

[@LawrenceTolman]

I agree!! I’m trying to keep this thing as light as reasonably possible, so an aluminum LS likely will be my engine of choice

[@joshherrman3201]

I cant wait to see this truck come to life. If it was me building it id do a ls with a whipple on it. Put a engine in it thats easily available and cheap for hp.

[@joeroad6618]

Big fan of the S10 platform, looking forward to watching this build come together!

[@AndyR1982]

As the excab 4x4 trucks are a little chunky, I would try to find an L33 aluminum 5.3 to supercharge. Keep some weight off the nose. Add some 4th gen fbody rear disc's for more bite in the COPO style. They bolt on the the 8.5 easy enough. Some s10 extreme body kit and it will look slick

[@nicholausbarrett8488]

Copo mini...... Nice

[@Joyrider564]

Solid roller NA LS. Spin it to the moon.

[@scotthultin7769]

145👍's up LT thank you for sharing 😊

[@steelwheels327]

This is going to be great!!! LS all the way!!

[@randysullivan5723]

Poly bushings in the front make a massive difference

[@jefflindeman2145]

What are you going to do to make the handling better

[@fataxe1]

Pinion shims wouldn't get you where you want? Reminds me of my old green 2wd from college. Absolutely love these silly little hardest working trucks. It'll look nasty slammed into the dirt if you go that route.

[@spacecase70]

LT the best thing to do is stuff an LS in it not necessarily supercharged, but I would go with the ceramic oil-less turbo in the back

[@joshc5512]

Looking forward to this build! Love the stock look since these trucks look good in stock form, lowered, with some decent rims. As for motor, definitely an all aluminum, v8, set up to turn some rpms with a nice choppy cam would be sweet! Call it the Brown Banshee? Haha

[@firedude1431]

Throw a vortec 4200 in there. I know how you like doing things outside the norm and I think you’ll like the 4200. Seems to be pretty stout with a few upgrades.

[@ItsDaJax]

It wouldn't fit. LS barely fit.

[@mahdialsenussi3066]

Amazing WORK ❤️ 👍🏼

[@nelsonramos2218]

Awesome channel. Every project is so unique. Keep it up brother

[@LawrenceTolman]

Thanks! Will do!

[@HicksGarage]

See if you can get your hands on the blueprint engise 4 cyl that uses a ls cylinder head. Also the 4wd xcab 5speed trucks came with the 8.5in 10 bolt.

[@BrianBlackall-lg9vt]

What about using the cast iron front diff as is and use a 4x4 posi lock mechanical cable to engage and disengage it. You’d have the best of both worlds with 2wd fun or Awd traction when engaged. As long as the locking mechanism is strong enough for the HP you want to run?

[@amaziin7733]

Damn bro I love your content your choices of trucks are amazing

[@raystevens687]

Wow LT I just saw on the internet a 4.3luv 2014 engine and yes it was built mainly a camshaft and a intake manifold one where they took V8 manifold cut it down to fit the 4.3 luv oh they put these headers on and ran them into 1 anyway when was said and done they started it up and I can say it sounded like a mean ole V8. I do wish I would of got the website but unfortunately I didn't.

[@DrFiero]

Glad to hear you're going to get rid of the Grenade80 locker! I blew up the one in my V8 S10 in a couple of days.

[@ryurc3033]

I had fairly decent luck out of mine. Biggest issue was people spinning one tire real hard without letting off

[@FastSS02]

Good luck finding ZR2 flares! I haven't found anyone that reproduces them yet. Also the ZR2's had mounts welded to the fenders to mount the flares, so it's not just a find them and bolt them on deal. The Xtreme kit is the street truck factory kit for the 2nd gen 98+ S10, but again those are nearly impossible to find as a complete kit.

[@charlesamey3144]

Yep, I've ran into the same problem - cannot find the ZR2 flares anywhere.

[@robertsnyder4963]

I've wanted to do this EXACT build as one of my dream builds (possibly using a blazer Xtreme chassis, for a typhoon clone, or a ZR2 to use most of the beefy parts)! My engine of choice was going to be the LF4 out of an ATS-V (to keep the turbo V6/AWD combo, assuming it would fit). Plus, the twin piston front calipers on the blazer would be a cheap and easy front brake upgrade compared to the single piston on the S10s.

[@KomotoseKomo]

really glad to see you taking on this build, if i can find a non beat to hell s10 reg cab, I wanted to swap a Lv3/6l80 with NV409 after watching your COPO series but I wasnt sure what front diff to use, well now i have an idea

[@markkinslow128]

Better than horsepower tv...kudos

[@srirachasauce8430]

4.2L vortec I-6. Insane power potential, and sounds awesome. If you must LS swap, 5.3L is best bet.

[@bradthacker9904]

Idk I think it would be kinda cool to put the 4.2 inline six that comes in like a trailblazer. Plus they don't sound bad with a turbo. AKA the Ameri-Barra

[@AngelenaCrowder-w1g]

Thanks for your content iam going to do a turbo 4.3 awd and set up these videos are great !!!!😊

[@geoffreyb3337]

Man I’m going to love this build ❤

[@black.phoenix.]

LT, the COBO truck is my favourite build from you. It just suits my tastes, specially the colour since I'm a sucker for Orange. I've been following you since the PowerNation times, being the Viper Truck build my favourite in that series (that heck it could had been even better that it's final show). For this new one I would really like to see something other than a Supercharged LS, since you have a touch for trying new non common ideas. Show us what you can make it different again.

[@mike_nunes]

YES LT! Building the street truck gm should've built! Syclone-ish, but better, after you built the one on truck tech, i thought about building an s-10 like you are now! Down to the ZR-2 flares and console shifter. Can also do the extreme flares for more of a subtle look, Gotta lower it though. Im excited to see this build! Keep the content coming!