Thermocouple Replacement for Rheem Water Heater. Save Money Fixing Water Heater DIY 2022

[@josef9001]

Thankyou for not adding any useless music. Strait to the point very clear instruction. Good video

[@WeTr1umph]

Appreciate you my guy! $23, 1 cut from the sheet metal, and an hour later we’ve got hot water again. KZbin university is where it’s at! My general contractor thought the whole burner assembly was shot. Buster out the multimeter just to be sure. Glad I did!

[@vinnythehandyman]

Your welcome! Glad everything worked out.

[@RogerPack]

You tested the old flame sensor with a multimeter, is that right?

[@WeTr1umph]

@@RogerPackyes sir.

[@chadalberty4563]

Thank You!!! As a homeowner, I absolutely love videos like this that help me with DIY repairs!!!

[@vinnythehandyman]

Especially when cost of living is so high. Glad the video helped.

[@jerrypimental4744]

Thank you so much for taking the time to make this video.. watched it, went to H/D and purchased the kit, had hot water in no time. You saved me hundreds, can’t thank you enough…

[@vinnythehandyman]

Your welcome sir! Thanks for taking the the to post and share your thoughts.

[@davidshumway9639]

​@@vinnythehandymanso I lost pilot. I went down read the instructions and followed them as written. What I didn't see in your video was if you held the pilot button down as you turned the valve to on. I get a pilot quickly. It looks just like yours did. Small and blue. But after I hold the pilot button down a couple minutes, as soon as I let up on it to prepare to turn the valve, the pilot dies. So is it likely my thermocouple or did I mess up by releasing the pilot button before I turned the valve. I thought that was the instructions but maybe I got it wrong. It says in the instructions to hold the button one minute. I held it a max of two. Do you think it's worth the effort to go try it again or just get. Thermocouple? Providing I didn't mess up when I released the pilot button before turning the valve to on 😅

[@logginlocos9023]

​@@davidshumway9639You didn't mess up. You can release the pilot button after a minute or so and the pilot should stay lit. You can then turn the dial to the desired temperature setting. The thermocouple should be sending an electrical signal of around 33 milivolts DC current as the pilot flame heats up the thermocouple probe ( a minimum of 15 milivolts is required). The electrical signal keeps the selinoid open so the gas to the pilot and the burner valve can flow. The pilot then keeps that electrical charge going and the selinoid open. The thermostat then opens up the gas valve allowing the gas to flow to the burner and the pilot then ignites the burner. You most likely have a bad thermocouple. If not, then a bad selinoid. If the selinoid is bad, you will have to have a repair person to replace the regulator/valve assembly. Good luck.

[@hannahpibbles725]

Thanks so much for posting this. I was able to follow step by step (with a few hiccups) and have my hot water back in no time. Huge relief!

[@jeffwilson1399]

Thanks for the video bud. Changed mine today. . $23 and I'm back up and running. Exactly like your video. Thanks again!!!!!

[@vinnythehandyman]

Great job! Thanks for posting.

[@SayWhatAgain109]

Thank you for narrating your steps very helpful. Just waiting on Rheem to send my pilot kit😂. Per Gas Co. Tech he said he could'nt help me out due to the position of the water heater??? This definitely explained & confirmed my next step. Awesome job!

[@vinnythehandyman]

Thanks for watching!

[@VinslomBardy]

Good video. I suspected a bad thermocouple was the cause of the burner not staying lit after ignition, so I used this video take apart the entire assembly and inspect. I found that the burner itself had accumulated a substantial pile of "dirt" (whatever it is that collects in the bottom of water heaters!), so I simply cleaned everything out and reassembled, figuring I would try this fix first, and replace the thermocouple as a next step if needed. Turns out, the unit fired up immediately and is back to making hot water. Thanks for posting!

[@vinnythehandyman]

Glad everything worked out David. Thanks for commenting and your support.

[@JohnDoeEagle1]

It could be a lot of different things rather than needing a new thermocouple. Before you go replacing any parts you need to make sure those vent screens are clean and not blocked with dirt/lint. There will be one in the center under the burner assembly and one via wire mesh around the outside of the bottom of the water heater. Your next step should be removing the pilot assembly and cleaning the thermocouple, flame sensor and pilot tube with a small brass or steel brush.... even steel wool. DO NOT USE SANDPAPER!! The sand residue melts and turns to glass when red hot, therefore it will become a coating and ruin the parts not sending the proper signal. After everything is all clean you reassemble and try to light it again. You also are looking to make sure the thermocouple is glowing red/orange. If not you can play around with the height and angle in relationship to the flame by utilizing the notches and retaining clip. If you don't have a red/orange hot thermocouple after a minute or two of the pilot light burning IT'S NOT THE THERMOCUPLE and that is the issue. Also if you see any water or moisture around the bottom of the water heater that also causes it to go out. IF you see any water where it doesn't belong that means the tank has ruptured/rusted out or cracked and at that point you have condemned that unit for replacement. The water heater is NOW shot.....not anything else or any other way. It can't be fixed and you need a new one! I'm not a "handyman".....I'm a licensed Journeyman HVAC technician with 22 years experience! John

[@1stinsonguy]

Thanks for taking your time showing us how its done! Pretty simple process, really

[@vinnythehandyman]

You’re welcome. Thanks for your support!

[@hairodemendoza6670]

Thx a million for making the time to put this together and published your knowledge. Best wishes always.

[@vinnythehandyman]

You’re welcome! Thanks for the kind words.

[@St3vi2_HOE]

Great video. One question. Did your inner door give you trouble opening. I ask because mine is. I took the four screws out and the door is still on solid. Any suggestions?

[@vinnythehandyman]

Hey bud! Sometimes they stick because of the heat and magnets on inside. Use a flat head screwdriver and crack seal on all four corners and open. You won’t hurt anything especially if you replace gasket.

[@St3vi2_HOE]

@@vinnythehandyman worked like a charm 😁. Thanks a lot 🤝 I appreciate your help.

[@vinnythehandyman]

@@St3vi2_HOE No worries thanks for your support.

[@stevenhernandez9091]

I just want to say thank you for your informational step by step installation! My water heater works like we first bought it.

[@vinnythehandyman]

That’s great news! Thanks for posting and your support.

[@TxJuggman67]

Thank you for the very detailed and easy to follow instructions.

[@vinnythehandyman]

You’re welcome! Thanks for watching 👍

[@drewhenrichsen7925]

Thank you! Heads up that there are a few recommendations in the instructions for the “gasket replacement kit with thermocouple.” that I also found helpful. One that I found particularly helpful was cutting the old thermocouple wire to make extraction easier.

[@vinnythehandyman]

Drew, thanks for taking the time to post helpful information and install techniques. 👍 I can see cutting the old one out would totally make sense.

[@esd9511]

Thank you for the video. It gives me more confidence to do this myself. I can fix a lot of things around the house but I've never replaced a thermocouple on a water heater. Thank you again.

[@vinnythehandyman]

Thanks for watching! Glad it helped you out. If the thermocouple doesn’t fix the problem, then I also have a gas control video that solve the issue. Thanks for taking the time to post and watch video. 👍

[@jessicaweems4877]

I agree!! I’ve replaced plug outlets and I fix things here and there since my husband can’t do it so we’ll anymore since losing his vision in one eye. A lot of ppl will make you paranoid about gas water heaters but I feel as if I can do it. Thanks for the video it boosted my confidence a whole bunch!!!

[@vinnythehandyman]

@@jessicaweems4877 thanks for watching and taking the time to post.

[@joey.g]

@vinnythehandyman --- can you normally see the ignitor spark in the glass (if its completely dark in the room). . .?? I think those can get a bad ground. . .All piezo I've worked with have a definite spark you can see. . thx

[@vinnythehandyman]

You should be able to see a small spark. If you’re still unsure you could always remove the cover plate and see. Won’t hurt anything

[@jeffreyshankel219]

Very thorough instructional video! Good job buddy!

[@vinnythehandyman]

Thank you sir for watching.

[@angelaroddenable]

Hello do you have a video showing how to replace pilot assembly pls

[@vinnythehandyman]

Unfortunately I do not. That would be a good one to do.

[@RogerPack]

Finally somebody doing this on a furnace similar to the one I'm trying to fix. Looks good, i might add is doing a bubble test on the gas lines when you're through :) also you don't have to pull the wire out of the igniter the whole button thing snaps on and off :) thanks again!

[@notannotan4289]

Very informative but, sorry to say that you missed a very important step that a home owner should do if he have to replace the thermocouple and removing the cover plate, these water heaters have air vents for air to move from the outside to the burner assembly, these vents which usually consist of small holes that by time they get covered with dirt and YOU HAVE TO VACUUM THE DIRT OUT TO CLEAR THE VENT HOLES if not the pilot will have a hard time to stay lit . Thank you.

[@chadalberty4563]

Thanks!

[@vinnythehandyman]

You’re welcome

[@abelrodriguez7188]

Thank you so much. I’m currently in process of changing mine out. What if the plate doesn’t come off after removing the 4 screws ?

[@vinnythehandyman]

Hi, thanks for watching. It’s the gasket on the inside that sealed pretty good. Use a flat head screwdriver and pry along the edges and apply a little bit more force when removing and then it will get unstuck. Hopefully this helps. Please let us know.

[@joerocha3482]

Thank you for the video. Very good and detailed. How long did it take to get pilot to lite once you replaced. I do see a spark but can't get it to light

[@vinnythehandyman]

Sorry for late response. I hope everything worked out. Sometimes it can take 3-5 min for the gas to circulate through system. Just keep hitting pilot until it lights.

[@marybannon7047]

Thanks so much. This video was extremely helpful, especially since I have the exact same water heater. Even though my water heater is under warranty, we didn't want to go another day without hot water.

[@vinnythehandyman]

You’re welcome thanks for taking the time to watch and post your thoughts have a great day

[@jcb83az]

Thanks for this video. I had a technician at the house and confirmed I needed a new thermocouple. He wanted to charge me $480 to replace it and said it was a 3 to 4 hour job. I know that couldn’t of been true…I happen to have the same exact water heater you just worked on and now it really feels like I can do this job myself. I just need to find that kit with the torque head screw driver. I don’t have that tool.

[@vinnythehandyman]

Go to Home-depot and find the entire kit. It will have screwdriver in kit as well. I believe the kit runs about 50.00. You got this man! Thanks for watching.

[@haroldreimers7117]

Great Video but I encountered a bump in the road. The gas line from the gas valve to the burner has left hand threads on my propane water heater. It took me a minute to figure that out. From the video it looked like your demo had right hand threads. Thanks, keep up the good work.

[@vinnythehandyman]

@@haroldreimers7117 yes, propane is left handed threads. Thanks for watching and providing feedback Harold.

[@Janedeereusa]

Thank you…..I am heading to the store to see if they have the kit….if not will order online….very helpful video even a woman can understand.

[@vinnythehandyman]

Thanks Jane for taking the time to watch and comment. Good luck 👍

[@Janedeereusa]

By the way I repaired my water heater thanks to you.....made a short video

[@vinnythehandyman]

That’s wonderful news! I knew you could do it. Thanks for sharing your experience.

[@Janedeereusa]

I am tickled pink......

[@chandrasekharlyf9212]

​@@Janedeereusawatched Jane's video and she did it easily. I discovered Vinny's video late, and had already done a lot of damage while taking my thermocouple out and putting a "universal replacement" in. Turns out the "universal" thermocouple slightly differs from the Rheem one and doesn't fit. Ok then I searched more on KZbin and found Vinny's video. Thanks man you saved the day. I got the Rheem gasket + thermocouple kit from home Depot and fixed the problem and got hot water back. I am a big time newbie, broke the grommet and the clip that holds the thermocouple in tight, but recovered after watching your video. I really appreciate your help in saving 100s of $ that I can't afford nowadays.

[@Karen-in8oz]

Are you supposed to smell gas after lighting it? Since the gas was turned off prior to turning it back on and lighting it?

[@vinnythehandyman]

Sometimes when you disconnect everything a little gas gets in the air. Also when you charge system a little gas has to filter through lines. Use dish soap and water and pour on connections to make sure nothing bubbles indicating a leak. Other than that you should be fine. Thanks for watching!

[@-keycha-8545]

thank you for the video it is very useful this video needs a like😁

[@vinnythehandyman]

Thanks for the kind words. 🙏

[@Wolves3rd2011]

Is there any power needed to be disconnected before doing this? (Breaker box, etc)

[@vinnythehandyman]

No, there is no power to unit. Just turn off Gas

[@gw1055]

So I had the lines disconnected, but can't get the panel off, seems like the gasket is stuck. Do you have any tips of getting it off?

[@vinnythehandyman]

Just use a flat head screw driver in pry off.

[@livenotonevil8279]

My new ignitor plug is round whereas the old one was flat. Can I just splice the old one one with a regulars wire crimp?

[@tatyrodriguez2389]

Thank you so much for sharing this extremely helpful video. I finally felt confident enough to try doing the job myself but I'm having an issue with remove that door with the little glass window, it seems to be stuck, it's not moving at all, any ideas or recommendations?

[@vinnythehandyman]

Hi, thanks for watching. It’s the gasket on the inside that sealed pretty good. Use a flat head screwdriver and pry along the edges and apply a little bit more force when removing and then it will get unstuck. Hopefully this helps. Please let us know.

[@tatyrodriguez2389]

Ok so needed help prying it open because my little scew driver wasn't cutting it lol but none the less got 🙌 thank you for that. Replaced the thermocouple myself but it still isn't staying lit after several tries, any suggestions?

[@vinnythehandyman]

@@tatyrodriguez2389 You could have a bad gas control valve. That’s the unit with the control knob. I would call Rheem or your local Ferguson and see if they have it in stock. Could be covered under warranty. Go to my videos in Description and look for gas control valve replacement. I have a good video on it.

[@CoryFPS]

Just did it myself thank you!!!

[@CoryFPS]

I'm still alive and now I'm clean!!!

[@mayenceli8267]

Wherebcan you buy the orange gasket where the wite fits through?

[@vinnythehandyman]

Hi Mayen, run down to Home Depot. They sell the entire kit.

[@vinnythehandyman]

If you can’t find gasket, then save the old one and use high temperature engine gasket maker from Autozone and fill any holes.

[@AGMoneys]

TY i have a different model but the concept is the same!!!❤❤❤❤🎉

[@vinnythehandyman]

Thanks for watching!

[@JimMelcher]

Perfect! Just what I needed. Thanks!

[@vinnythehandyman]

Thanks for watching!

[@JimMelcher]

@@vinnythehandyman Ok, this morning the water was cold again. If the new thermocouple is fine, any ideas what should I check/replace next?

[@vinnythehandyman]

Check out my gas control valve video. This has been another issue with Rheem. Go to local plumbing house and see if they have a compatible gas control valve. kzbin.info/www/bejne/epOpaKGKrJ2VpLM

[@JimMelcher]

Super! I will do that, Vinny. Thanks a ton!

[@raulbarriga7416]

Why do this approach (besides the parts cost difference) instead of replacing the entire pilot assembly with a replacement kit from the manufacturer? Just curious.

[@vinnythehandyman]

Most are still covered under manufacturer parts warranty. They only ship parts and labor is not covered. That was the case in this video. Owner was covered under warranty and shipped out free parts.

[@scotttang6229]

Thank you! Going to fix mine tmr 😊

[@vinnythehandyman]

I also have a gas control valve replacement video as well. It could be 1 of 2 issues. FYI

[@atomant25gtadams26]

I’m going to try this today. I’m having an issue with the igniter not lighting the pilot. I can see a spark right at the button and it’s not traveling to the burner. Any ideas?

[@vinnythehandyman]

Could be a bad gas control valve. I also have a video on that as well. I would say replace control valve first.

[@Fierysaint1]

At the online store I have a choice to buy either the thermocouple alone or the one that comes with the gasket. Do I really need to change the gasket like the plate says? My water heater is only 2 years old.

[@vinnythehandyman]

Honestly I believe you are ok unless you damage it.

[@JohnMartin-ni2pj]

People, you need to file a class action lawsuit against the manufacturer of these devices, get together and make a stand against them

[@kylekleespies783]

That circle gasket that the thermal couple goes through broke to pieces when pulling it out and I can’t for the life of me find a new one. Do you know where I could find that or how important it is??

[@vinnythehandyman]

Very important! I would check Amazon or go to Home Depot. If they don’t carry then go to Autozone and buy red high temp gasket silicone and form gasket until a new one comes in. You will be fine.

[@SOGnba2008]

Is it necessary to replace the gasket? Also, my top 2 screws on the cover plate won’t stay in place

[@vinnythehandyman]

Hey Omar, if you buy the kit then it comes with it. If you don’t replace gasket you can use existing and will be fine. Just make sure it’s not ripped or damaged. Thanks for watching bro.

[@SOGnba2008]

@@vinnythehandyman thank you for your prompt response. The other problem I have now is that the round orange silicone/rubber piece that holds the wires on the cover plate broke. Any recommendation?

[@vinnythehandyman]

@@SOGnba2008 have to treat my fans good! Omar, you can use red automotive gasket silicon that has I heat tolerance. Use cracked washer and spread the red silicone around it and you should be good 👍.

[@vinnythehandyman]

Hey Omar, just checking in to see if the install went well? Hopefully your up and running. -Vinny

[@Hyperwind5]

I have the same issue, my rubber gasket broke into several small pieces as well as partially crumbled away... Is it possible to find a replacement for it?

[@moonswift300]

I can't get the gas connector to unscrew on mine. It's stuck tight. How hard can I crank on it with a wrench to undo it? I've gone just shy of breaking my own wrist. 😱

[@vinnythehandyman]

@@moonswift300 yes, unfortunately can be very tight because of thread sealer. Use a pipe or larger crescent wrench to help break it loose.

[@moonswift300]

​@@vinnythehandyman I couldn't get it unstuck. Been trying for the last hour now. I was beginning to strip the bolt and bend the main gas line from pulling a pipe wrench. I can't believe one bolt is going to cost me hundreds of dollars. I'm so embarrassed. Your video is wonderful. I'm just stuck at step one...

[@vinnythehandyman]

@moonswift300 try using counter pressure with another crescent wrench. That way the control valve doesn’t get damaged. Maybe spray some w-d 40 on it to help loosen. Sorry it’s been so hard.

[@moonswift300]

​@@vinnythehandyman I'll give that a try soon. Thank you for your kindness! As I said before your video is perfect! Who could have predicted this? 😩

[@vinnythehandyman]

@moonswift300 💪🫡

[@Kookamungawerewolf]

That was awful nice of some engineer to put magnets in that gasket to hold it in place. He or she deserves a bonus for that!

[@keithwilliams4889]

Thanks bro this was my problem appreciate it

[@vinnythehandyman]

That great to hear man! Glad you enjoyed the content.

[@kraineyjr]

Did you have to turn the gas off?

[@vinnythehandyman]

Yes

[@joey.g]

great video btw -- good explanations

[@IKONBLOGGERS]

Is that thermocouple 18” or 24”?

[@vinnythehandyman]

I believe The Home Depot kit was 10” for the Rheem.

[@kermitefrog64]

Thank you for the video. My water heater has been shutting off at a minimum of once a week. I have a Rheem gas water heater with the Honeywell device. I bought the gas water heater at Home Depot. Hopefully and can take care of this on going hair pulling frustration.

[@hotpxl618]

I tried the home depot one but couldn't remove my thermocouple on the unit. Did you have better luck?

[@vinnythehandyman]

You can’t remove face plate or actual thermocouple?

[@hotpxl618]

@@vinnythehandyman the actual thermocouple

[@vinnythehandyman]

@ since you have a new one, I would just use tin snips a cut out in pieces. I’ve never had that problem before so it’s a rare one unfortunately.

[@hotpxl618]

@vinnythehandyman its like its locked in place. I'll link a photo

[@al213rd]

Thank you

[@brianj7478]

My screw in tubes don’t want to go back into the water heater control :/ they keep popping out whenever I’m halfway through the screw in

[@vinnythehandyman]

You might have them cross threaded. Go counter clockwise a full turn then clockwise so threads can grab. Hopefully that works 🫡

[@anythingcanhappen23]

Thanks for this video!

[@vinnythehandyman]

Thanks for watching. I also have another video removing the gas control valve that might help you diagnose the problem. Happy Holidays!

[@BigChavezChavez]

Awesome video, I would feel comfortable replacing this part by myself now. In your experience, would you recommend an electric or gas water heater? Thanks in advance for the response!

[@vinnythehandyman]

I always recommend gas. Long term you have the ability to save more money. Also, they are easier to maintenance. Thanks for watching!

[@swede5209]

I was about to replace mine but a plumber told me it was probably the gas valve. Rheem had a bad run of gas valves in 2019-2020. He was right. It wasn’t an awful job.

[@vinnythehandyman]

Yes they did have a bad run on gas valves. I also did a video on that as well. Glad you’re up and running.

[@davidshumway9639]

Yeah my Richmond 40 gallon with the same looking valve as in this video was built in November 2019. The gas valve took a poo within a couple years. They replaced it for free. Now my heater just died again. The pilot lights but as soon as I lift the pilot button to turn it to on, the pilot dies. Held it a couple minutes. Not sure if it's the gas valve or thermocouple this time. Thing is only 3.5 years old (less than). My first heater that came with the house was a Rheem. I think. Nothing ever happened until it finally sprung a leak after year 16.

[@Zsigmund]

Thank you, very helpful!

[@vinnythehandyman]

Your welcome. Also check out my gas control video as well. Could be 1 of the 2 problems Rheem is having with their water heaters. Thanks for watching and for subscribing!

[@bgnoggin]

Why is my main gas line reverse thread???

[@vinnythehandyman]

I have seen that on propane fittings. I’m sure you will be fine but definitely rare for residential gas lines. Maybe a master plumber can elaborate. Thanks for watching.

[@bgnoggin]

@@vinnythehandyman It is propane. That's it. Through me for a few. Was trying way too hard to remove it. Then I figured, what the heck and went reverse.

[@vinnythehandyman]

@@bgnoggin learn something new everyday 😂

[@americanmade422]

Did you turn off the breaker when doing this?

[@vinnythehandyman]

No sir. However if you have a energy efficient water heater with a plug in then yes.

[@americanmade422]

@@vinnythehandyman I just replaced mine and this video saved me a ton of money. Thank you!

[@vinnythehandyman]

@@americanmade422 Thats great news! Glad the video was beneficial. Thanks for you support 👍

[@Hyperwind5]

Hmm what happens if my rubber gasket was so old it just fall into pieces, is that a part I can replace?

[@vinnythehandyman]

Hey bro! Yes you can buy the gasket at Home Depot for 16.00. Easy fix

[@Hyperwind5]

@@vinnythehandyman Thanks! Is there a special name for the gasket? Just want to make sure I get the right one

[@vinnythehandyman]

@@Hyperwind5 as long as it’s says Rheem. Should be a red gasket.

[@FernandoRodriguez-q7f]

The orange circle that holds the lines cracled and broke on me..heat rotted or something..

[@vinnythehandyman]

You can buy a repair kit at home-depot. I believe there are less than 30.00

[@williamboatner7689]

Do you know I just called out a company to change my thermal couple and they wanted to charge me $345.00 to do what you just did, so I thank you sir

[@vinnythehandyman]

Glad you were able to pocket some grocery money. My channel is dedicated to helping hard working families save money. Life is already hard enough. Thanks for the comment and watching. -Vinny

[@jessicaweems4877]

They wanted to charge me $250 + the part. I’m going to buy the kit today and go for it!!!

[@vinnythehandyman]

@@jessicaweems4877 you got this👍

[@lewis45407]

I’ve done all this and for the life of me can’t get the burner and assembly to slide back into place inside the water heater

[@vinnythehandyman]

Get on your stomach and shine a light inside. You will see a support clip or brace where the burner slides into. Some models have different brackets. Still very easy you just need to look inside. Let me know if that worked. Thanks for watching.

[@vinnythehandyman]

How did the install go?

[@lewis45407]

@@vinnythehandyman I didn't know you replied to me. The install went really good. I think I was overthinking a bit. It slide into place finally and I haven't had any problems with it since the day I messaged you. Btw you definitely earned a sub from me. This vid really helped me.

[@vinnythehandyman]

@@lewis45407 good to hear man! Thanks for the support.

[@scottiejacobs9580]

Dude mine still leaking around the screws

[@vinnythehandyman]

I’m guessing you mean water? If so you can unscrew top cold water line to give it air so it can drain faster.

[@mattalford3932]

If you have that gas valve and the pilot goes out try removing that white thing between where you screw the thermocouple into the valve before replacing the thermocouple. These valves are faulty, and that's the fault most of the time lol. So irritating I have to replace another gas valve lol.

[@vinnythehandyman]

Thanks for taking the time to watch and reply. All tips are definitely helpful! Hopefully your control valve will last this time. 🙏

[@joshualux8309]

Those two wires go to a thermal fuse that can not be reset. Rheem will warranty the gas valve but give you the same pos back. I wish Rheem was more transparent about the problem being that I’ve probably replaced nearly 50 of those valves in the last two years alone or better yet come up with a solution that works.

[@JustinFromBSing]

Subbed. Please come back with more DIY vids!

[@Okaybob]

NEVER, EVER, use Teflon tape on gas fittings. You may think you're being careful to not put the tape too close to the edge, but 2 facts remain. 1). Its unnecessary 2). The potential for a small piece of Teflon tape to come-off, and stick to the valve seat is still there. This will hang the valve open. We don't want gas leaks.......do we? NEVER use Teflon tape on gas fittings. The same for Petroleum type "gas". NEVER on Carburetor, or any other fuel fittings.........same reason.

[@vinnythehandyman]

Tony, Appreciate the time you took to point out potential problems. of course we don’t want potential gas leaks. Just my personal experience’s but I have had some gas leaks on fittings that didn’t have gas rated Teflon. That’s why I’m so careful BUT APPLIED very carefully as a potential backup and gas leaks went away. To not use Teflon period is fine to. I totally agree with you. To Viewers reading this YOU DO NOT NEED to use Teflon tape. -I believe I was careful in the application and made note of it. I do appreciate your experience and knowledge on this topic. Tony, thanks for taking the time to watch and post.

[@ryanbuck3789]

Trfolon does nothing of or a flare fitting except mak3 a potential void causing the flair not to seat. SMH I see it 3very day especially on the flex hook up.

[@naimi9584]

I so wish I would have bought it years ago

[@ready1]

thanks mate! some other videos were suggesting the sensor above the thermocouple (white thing) that connects it to the gas valve is often the problem also. For example here: kzbin.info/www/bejne/aZyyeJuArLaHopo How can I tell whether its that sensor that is the problem, and not the thermocouple you suggest replacing?

[@yami4g63]

So you know the flare makes the seal yet you still put the tape on the threads??? Why. 100% pointless......

[@vinnythehandyman]

You are 100% correct. No need for tape. It’s just a layer of added protection for me if done properly.

[@tonymc3817]

Wow, that was hard to watch.

[@vinnythehandyman]

That bad? Suggestions if I missed something. Thanks for watching

[@MissionRealEstate]

Thank you!