INSTALLING AN 11POLE STATOR IN YOUR GY6 ENGINE

[@perfypudon8108]

So what kind of rectifier should be recommended when upgrading from 8 to 11 poles? How many rectifier wires should it be?

[@Theruckshop]

5 pin rectifier

[@itshighlesshippie]

Do you have to set a gap on the pick up coil?

[@andrewc3287]

What impact wrench you using? I have a 20volt one and it's not working and I tired a pneumatic one with around 90 psi and still didn't have enough power to get that bolt off. Help please lol.

[@seagangstab2637]

Good lookin out brother, I'm doing it right now.

[@mandapalque]

Which scooter do you have? Did it come with the 8 pole triface stator? Could you please tell me which brand and model is it? Thanks.

[@humanbeingfromearth]

Flywheel nut is reverse threaded??

[@jsmokzalot9238]

No

[@A_Stereotypical_Heretic]

No. The puller is inserted using a reverse thread/left hand turn motion

[@the473hustler7]

i have a scooter sym crox 150cc , its ac fired scooter i wanna convert it fully to dc , what would i need to complete this conversion ??.. thank you ,..

[@humanbeingfromearth]

Does the 150cc conversion usually remove the ecu? I'm new to this, just got a ruckus with gy6 conversion. Thanks

[@Theruckshop]

yes

[@humanbeingfromearth]

@@Theruckshop thank you for your response!

[@The1CrazyAznBoy]

hi i need some help i just got my self a 11pole stator but is doesnt bolt up the plate in the back of it. Any where i can buy the back plate? i dont know whats its called

[@A_Stereotypical_Heretic]

Did you get sorted?

[@mandapalque]

So, using your 8th pole wiring you just can put and 11 pole stator?

[@Theruckshop]

if you are using the atr harness it is made for both 8 and 11 pole but is recommended to use the 11 pole stator since the 4 pin regulator is not strong enough to hold the volts coming off the stator. if you have the dan max harness the 8 pole works fine and if you upgrade to 11 pole then you will have to re-pin the harness which it states how to under the danmax link on our site

[@2FrEsH4ya617]

I’m having voltage problems with my stator I changed from 8 pole to 11 pole stator on a gy6 swap but I have stock harness for ruckus clone and I have a ncy 4 pin regulator..what will I have to do to keep everything working good I want to keep this harness is there a way I can please let me know

[@A_Stereotypical_Heretic]

@@2FrEsH4ya617 buy yourself the correct rectifier. You need a 4+2 rectifier, and they are about 4x the size of a 6 or 8 pole one. Youll know when you see one.

[@blak319]

what does pink wire on 11pole stator connect to?

[@jsmokzalot9238]

It's red... probably just faded and now looks pink

[@jjabrahms7163]

Are these 3 phase?

[@jsmokzalot9238]

Long story short I've got an 11pole 3 phase stator and I want to put it on a 150 gy6 that currently has 8 pole single phase. Is this possible?

[@xavinb8225]

check out @kachiskid

[@A_Stereotypical_Heretic]

You'll only have 1/3 of the poles working for you so no it's pointless. These poles aren't in one phase like the smaller stators. You need each yellow wire to be feeding your rectifier with its own dedicated terminal connection to get 100% effectiveness from the stator. You need a 4 pin+2, 3 yellow pins, one ground on the business side. If you don't have the correct pin out on your rectifier buy the corresponding one or keep your 8pole on the motor...it will produce more juice than an 11 pole with just one phase working.

[@jcmfrancisco021]

what is the benefit of this upgrade?

[@Theruckshop]

Jack Francisco better charging . More Poles means better charging . Charges faster and more since there's 2 more poles per rotation

[@jcmfrancisco021]

The Ruck Shop hmm what do you mean by charging, does it charge the batterries? sorry I'm new with this stuff, I also have a gy6 and want to do this also

[@Theruckshop]

Jack Francisco yes the stator charges the battery

[@carlberner3797]

@@Theruckshop you mean 3 more poles?

[@marcusriley4105]

so are you using a 8 Pole or an 11 pole magneto or does it matter?

[@Theruckshop]

marcus riley it's does not matter but we are using a stock flywheel on an 11 pole stator .

[@amjtech]

Red Loctite? No thank you. I use blue and never had an issue. Stators on gy6 tend to fail way more often then I would want to fight to get red locktite held bolts out. I don't always have my impact handy.

[@Theruckshop]

Andrew Johnson we do this a lot more than you do. Blue does nothing with the heat of the motor. Yes you can use blue but red works best .

[@A_Stereotypical_Heretic]

@@Theruckshop what a dick response. Of course red works best for keeping the bolt locked...that wasn't his point. Ever had one of those little head bolts snap in half because some genius used red loctite? Apparently not. High temp blue loctite is rated upwards of 450°, which is the perfect locker for these engines. They don't exceed 300° and if they do you have more problems than thread locker. Red is by far extreme overkill on this little guys. That's friggin auto engine rated head bolt stuff man! 🤦 Not a 150cc engine.

[@avatheavydog7053]

I feel Your gonna be bummed you used red loctite

[@Theruckshop]

been doing this for over 15 years with bikes with no issues

[@A_Stereotypical_Heretic]

Yup. Just a matter of time.

[@mandapalque]

My 8th pole stator does not match any of the 11 pole stators. My 8th pole stator is a 5 wires stator. You should of mention that there is 2 different 8th stator s. Thanks.

[@Theruckshop]

we only sell ac stators so this is what we do the videos on, and their are ac and dc but none of our harnesses use dc

[@mandapalque]

The Ruck Shop my scooter is AC. It just happens to have the cheapest 8 pole stator. Thanks for the answer guys.

[@mullervolker9814]

*have

[@A_Stereotypical_Heretic]

@@Theruckshop all stators are AC...Js.