Thread Tension Assembly HOW TO: Disassemble, Adjust, and Replace Your Thread Tension Assembly

All the thread tension assembly essentials are here. Need to adjust the tension? Want to take apart the assembly, fix it, and put it back together? Or how to replace your assembly in the machine? Watch our video with VP Joseph Park to find out!
How To Adjust Your Top Tension: • HOW TO Adjust Top Tens...
Purchase New Thread Tension Assembly: www.abcsewingmachine.com/prod...
Purchase New Take Up Spring: www.abcsewingmachine.com/prod...
Purchase Screwdriver:
www.abcsewingmachine.com/prod...
Chapters:
00:00:00 Intro
00:00:27 Tools Needed
00:01:00 Removing Thread Tension Assembly
00:01:49 Disassembling Thread Tension Assembly
00:02:10 Removing Take-up Spring
00:04:17 Inserting Take-up Spring
00:06:00 Adjusting Take-up Spring Tension
00:07:00 Reassembling Thread Tension Assembly
00:07:48 Reinserting Thread Tension Assembly into Machine
00:08:06 Inserting Thread Tension Assembly Spring
00:08:38 Take-up Spring Positioning
00:09:20 Thread Tension Assembly Positioning
00:10:06 Checking Thread Tension Assembly Positioning
00:11:08 Identifying Thread Tension Assembly Issues
00:11:45 Purchasing New Thread Tension Assembly
00:12:08 Outro
Check out our KZbin channel & Subscribe for our weekly tutorials: ➥ / abcsewin. .
➥Website: www.abcsewingmachine.com/
➥Instagram: / abc_sewing
➥Facebook: / abcsewingmac. .
For questions, leave us a comment under the video below!

[@joebernstein2524]

This is one of the best instructional videos that I have ever seen. Everything is explained very well and important points are emphasized and repeated. I can't say enough good things about this video and its presenter. Job well done!!!!!!!

[@loribolden6154]

Again I Thank you for sharing your knowledge and experience.. Lately I am worshiping your knowledge !

[@jvcovers1003]

Bro,thanks Gat that problem fix...🙏👍

[@tommyibex2626]

just bought and rebuilt a typical gc0303 and this was the final piece of the puzzle getting it all back together. thanks great video

[@barbulrey5178]

Thank you so much for this video! My entire assembly came out and I was sewing by pushing it back in every few stitches! And all it took was looking for where the Lock Screen was and tightening it!!! I am in business again. Thanks!

[@dfrank2044]

Great presentation and well explained from the professional. Thanks

[@tech-teachSL]

Very well-explained. Thank you so much.👍

[@hirow08]

Very detailed. Needed the angle of the take up spring. Thanks for this 👌

[@maggiemcallister9972]

Thank you so much!!!

[@davidsuman2444]

Thanks so much 🙏 Sir . Very useful this video 🙏

[@brianhaddock2020ICU]

Fantastic.. Top man

[@bulusdavou4865]

Thanks a lot

[@abuhussain26]

Thx

[@ashwadhamini2727]

Thanq thanq....

[@boutch050]

Hi Can u do video on how to set the foot max hi for Adler 269

[@MahmoudElganzoury]

What is the best sewing machine?

[@Ben-uf8eg]

i cant get the last peice out. the peice that holds the spring

[@josephpark2256]

Some units have silicone to hold it in or it's just sticky or gunky. Night have to use some needle nose pliers and/or wd-40 to break up the build up.

[@Ben-uf8eg]

@@josephpark2256 used wd40 and two needle nose pliars and still no luck. any other ideas? Thanks for the help

[@josephpark2256]

@Ben you may have to damage it to get it out (new assembly not expensive so be prepared to get that ordered) There is a little hole where the spring comes out. Use that and put a screw driver against there to hit it (clockwise /counterclockwise) to get it to turn and loosen up. With the wd40 in there already it should break up easier once you're able to get it to turn a little bit. PERSISTENCE/PATIENCE IS KEY! Good luck!

[@Ben-uf8eg]

@@josephpark2256 I heated it up with a blow dryer and got it out!. Thank you