My father taught me how to change tires years ago when I was a kid with a bumper jack and tire irons. Where I am tire shops and garages charge $30.00 USD to change one tire. I bought a tire changer for $50.00 USD at Harbor Freight Tools and I have saved several hundred dollars doing them myself and I have done some for friends and made some money. I didn't ask them for money. They were happy they were done cheaper. I have a balancer as well.
@TheSnoopindaweb22 күн бұрын
💬> 👌 Stubborn is good 🤠 Yup❗ G~G.
@mike7gerald21 күн бұрын
Balancing the tire is essential-it's no use changing it if you don't balance it afterward. How expensive was the balancer?
@johnbreen304321 күн бұрын
@mike7gerald $50.00 at Harbor Freight and it works fine. You wear off enough after a few miles anyway that somewhat makes it not matter anymore. I changed plenty of tires over the years and never balanced them and hadn't had a problem.
@deanyanko332620 күн бұрын
I'll tell you one thing breaking the bead on foreign rider mower rims with small pry bars bends the metal thus rim leaks no fun.
@doradean30978 күн бұрын
I read somewhere the tire balancer usually goes near where the Schrader valve is located, is that true, anyone?
@MichaelDouglas-nt7ti25 күн бұрын
Most people will try this and end up taking the tire to a shop to finish the job 😂
@ЗахарЗахарович-р2к28 күн бұрын
Есть ещё вариант: поддомкрачиваем автомобиль и снимаем колесо с автомобиля, затем кладем колесо под диск или барабан снятого колеса и приспускаем домкрат, авто свом весом разбортирует колесо. Или положить на шину доску и наехать колесом, тоже помогает.
@ruslankeller38627 күн бұрын
Пробовал эти 2 способа - не помогло.
@ИгорьНиконоров-ж8п26 күн бұрын
В 80х годах в основном так и разбирал.
@doktorbotving24 күн бұрын
А балансировать поедем в шиномонтаж?
@ИгорьНиконоров-ж8п24 күн бұрын
@@doktorbotving в 80годах мы и балансировали сами, правда редко, когда совсем хреновое колесо, да и на большинстве тех дорог балансировка была бесполезна.
@ЗахарЗахарович-р2к24 күн бұрын
@doktorbotving Колесо "бить" начнет поедим, а так что зря время тратить. Грязь и снег налипает, камешек в протектор попадет ездим же как-то.
@БорисЖемчужный27 күн бұрын
Все эти варианты были актуальны и ими пользовались в далёкие времена, когда не было шиномонтажных мастерских на каждом километре. Ничего нового в этом нет. У всех были в багажнике монтажки и запасные камеры в дорогу. Не было безкамерных колёс.
@mkrp420 күн бұрын
На дисках не было кольцевого выступа внутри для бесканмерных шин, шины были выше и уже в поперечном сечении; после такого "монтажа" с помощью напильника диск можно будет выбросить из-за ржавчины
@valeritchkalov354718 күн бұрын
Ну, уметь-то надо всё равно, мало-ли какие приключения приключатся. Вот накачать смонтированную бескамерку на дороге, не имея компрессора- это квест еще тот! Было и такое в лихие 90-е
@johnpaserba229926 күн бұрын
Some put a little yellow Arrow on the rim and also on the tire. The arrows point at each other. That way when you take the tire off to patch it, you can put it back on exactly where it used to be, and will not need a new wheel balance
@tonyteel25 күн бұрын
Just put a mark on the tire where your valve stem is
@Minimumpilot24 күн бұрын
Wo kann man eine Reifenfeile kaufen?
@TheSnoopindaweb22 күн бұрын
💬> It never takes that much longer to verify and then decide if any weights need installed - correctly 🤠 Yup❗ G~G.
@MsGem22217 күн бұрын
Если прокол заделывается, или ставится камера, то балансировка колеса нарушается.
@patrickvanbramer503719 күн бұрын
You only need a jack... and latex gloves, scissors, A Strong rope, screwdriver, lighter, drill with hook thing (optional) funky music and pure Magic before your eyes. This absolutely was the best pass time. Thankyou
@Slipshott24 күн бұрын
Hardest part is the part he didn't do......he never actually took the tire off the rim.
@rgfisher2116 күн бұрын
And it still had to be balanced
@username817114 күн бұрын
That's not the hard part, it's breaking the bead that's hardest, that's why I use my log splitter. Removing a tire is easy, as long as you get the bead into the drop center opposite of you, then it all works out fine.
@leslieedgardlindop720212 күн бұрын
Hi easy way l have done this in the bush is to use your car to run over the tyre and brake the bead and use tyre levers to change the tyre .cheers les from Adelaide south Australia
@Crushwokery4 күн бұрын
Hardest pert is watching this bull💩. Only reason I watched it was hoping for something clever I've not see in 30 years as an hgv truck mechanic. Sadly I was wrong.
@DanielMcCollough-u3rКүн бұрын
Hardest part is listening to the narrated voice😂😂😂
@alexeyb9127 күн бұрын
Я так лет 40 назад делал, когда не было шиномонтажных мастерских. А теперь это дикость какая то.
@JarKarracos18 күн бұрын
Это брат происходит у них,у тех кто считает себя самыми лучшими в мире...21 век,он тут показывает,что мы раньше при помощи двух монтерововок делали😂
@MsGem22217 күн бұрын
Смотри выше - чел отписал, что у них ремонт колеса стоит 30 долларов, а шиномонтажный станок в их Леруа - 50. За такие деньги я бы и себе такой станок прикупил. 😉
@РомуальдАльгедрасович-ш7и16 күн бұрын
Я живу в краю рукожопов и криворуков, на одной шиномонтаже порвали новую резину, на другой -спускает по диску два колеса( не проверили после сборки ) Так что буду сам делать раз в год - надëжнее будет, да и нервы! ☝😃
@EvgenMay15 күн бұрын
@@РомуальдАльгедрасович-ш7и все мы живем в таком краю. Так что приходистя много самому делать, но шиномонтажа еще не дошел.)))
@charlesleonragain27 күн бұрын
lubricate tire bead and it will work a whole lot easier
@dontrend595626 күн бұрын
using a file as a pry bar is a very bad idea.
@DogSt17 күн бұрын
Using your mom's bran new scissors to deflate it is also a bad idea 😂
@andrewreid222816 күн бұрын
I thought that too.
@fjyamaha-fc7cm15 күн бұрын
😂
@fulviobertotti678528 күн бұрын
Ne ho cambiati tanti di pneumatici ma non avevo mai visto quel sistema. Se ti trovi nel deserto è ideale. Complimenti.
@arnoldalt257126 күн бұрын
would you have an air compressor with you in the dessert?
@alanm893223 күн бұрын
@@arnoldalt2571I've changed a tyre myself & got it pumped up with just a foot pump, so it is possible. I usually pop it onto the rims by lighting carb cleaner but the last time I managed it with just the foot pump. I always carry the foot pump in the car, so I'll be ready for that tyre change in the desert!
@JK-zl7vv21 күн бұрын
While you had the jack pushing the lip of the tire into the center ring of the tire, would be the time to pop the bead of the tire over the rim across from the jack, then the tire would come right off. 😎👍
@kenbellchambers457717 күн бұрын
I rectangle of wood such as a scrap of 20mm plywood or similar piece of tough wood might prevent the feet of the jack from damaging the tire. This idea of using the force of a jack could be handy for other jobs.
@thisisnumber025 күн бұрын
I missed the bit where the tyre came off the wheel and the bit where the new tyre went on.
@markpaquette963125 күн бұрын
That and the part where you inflate the tire with the jack lol
@paulhillman40024 күн бұрын
The tyre centre wouldn't let him video that part.
@tamassollei447324 күн бұрын
Mert ez egy Dewalt akkus fúrógép bemutató videó
@wackingjack23 күн бұрын
This video is missing so much it's a joke!
@RikaPearson23 күн бұрын
That's the easy part. Breaking the bead is the hard part.
@kws195726 күн бұрын
I change my tires too alone but with a different method, but the shown technique here seems to be simpler.❤❤❤
@Paramecio_Z13 күн бұрын
Excelente tutorial. Muchas gracias. Saludos desde España.
@helmutsandner482323 күн бұрын
Sehr gute Idee, wenn man nichts anderes zur Verfügung hat 👌😎 Aber wenn man mit einer Feile arbeitet, ist etwas Vorsicht geboten, zumindest dann, wenn man kein Gefühl hat und nur Kraft ... 💪💪💪🥳😂😂😂Aber Alles in Allem 👍🎖
@MrMickeycase16 күн бұрын
Thank you. It took for decades to know the simple way as you taught
@FixItFast116 күн бұрын
Is that sarcasm or did you really like it?
@joeclark788810 күн бұрын
Great ideas,great work!We almost always have everything we need to do any job if we just take the time to think. Invest in some tire irons. Never pry with a file!
@groblerful26 күн бұрын
That file you use as a tire lever is likely to snap
@tonyteel25 күн бұрын
yes , files are too expensive to pry with
@markwarnberg950424 күн бұрын
Crowbar!
@michaelhemric522824 күн бұрын
They are pretty brittle as well when you put force on them like that
@WilliamMarble-q1b18 күн бұрын
@@michaelhemric5228 Listen to these guys!
@keneaton285524 күн бұрын
The only person in the world that is not completely irritated by constant background music is the person making the music.
@JohannesC-c9k23 күн бұрын
Yes it annoys me to and video makers rotate their hands holding components and tools, we can see what they are instantly most of the time. Low self awareness is the cause.
@drueatcer21 күн бұрын
I must’ve had my sound off, did not hear any background music.
@depmode947220 күн бұрын
Would have been a ton better without the annoying music … maybe just a voice step by step or even just a mime version 😃
@juntjoonunya921619 күн бұрын
He's irritated by it too
@timbarnett389825 күн бұрын
This is how my dad taught me too change tire from rim some 60 years ago! Thanks for sharing!
@francstrucl450624 күн бұрын
Ne verjamem prvič videno kaj takšnega zakaj niste objavili
@MTB_MICK25 күн бұрын
Nice trick to break the bead. I use a different method for fitting though. A heavy duty ratchet strap around the circumference of the tire, tighten then inflate with a compressor. 👍
@Владимир-ф7щ6п25 күн бұрын
Классно.. Быстро и не дорого. Спасибо. Попробую этот приём. Из России. Сибирь.
@umac0121 күн бұрын
I Have never seen this done before and now I have thanks to KZbin witnessed it done twice. There are many more demonstrations how to do this keep them comming.
@CreatorTips.007Ай бұрын
"Such an ingenious technique! Changing a tire in just a minute with this method is absolutely brilliant!"
@peterpeter377Ай бұрын
Stupide idiots😂😂😂😂
@TrinitaMatoumona-hq2dv26 күн бұрын
En une minute? J'ai compté plus de 7 minutes dans cette vidéo!
@endurofan985425 күн бұрын
sarcasm. at its finest 🤣🤣🤣
@davidpalmer974025 күн бұрын
How do you balance it?
@jerrylboutin7 күн бұрын
Been doing this for along time but you need to start it like he did but when the gap shows pour dish soap in bead than run your jack all the way than hit the bead with a bar and hammer it will pot quick
@ericracine630524 күн бұрын
In one minute the title say and the video last 7 minutes 🤣😅😂
@shawnpink885723 күн бұрын
And he only took the tire off.......
@naeemahmad406724 күн бұрын
Don’t kill your self and look after your back . Health is everything, money is not everything
@Daniel_Antonio_Arellano78226 күн бұрын
As a young man I removed some tires. The use of the jack was different though. I would use what we called a Handyman jack. That was the brand. It stood upright. I would put the edge of the jack against the edge of the wheel. Using basically the same principle as this one. But using it on both sides of the tire. Then removing it. It is easier to remove if you do both sides.
@tonyteel25 күн бұрын
Always nice till it slipped and got a whack on the shin
@Daniel_Antonio_Arellano78225 күн бұрын
@tonyteel True. It probably could have happened. But never did.
@davidbertrand688425 күн бұрын
After jacking the tire away from the rim, those cracks in the tire 🛞 means it’s tine for NEWTires
@truhunk124 күн бұрын
Mission accomplished. I like saving money, but some things just aren't worth the trouble. I'll let the tire shop do it.
@michelebreese594014 күн бұрын
Yep. Many times. I do it for the musel power
@LARSDIAGAUTO15 күн бұрын
Thank you for this vidéo 😉
@DailyTipsFix11 күн бұрын
I will give it a try.
@AlanAlan-sz5zd28 күн бұрын
Hardest way i ever seen to change a tire, and I have changed a lot of them by hand
@nedcramdon130625 күн бұрын
Ya, that was almost excruciating.
@jigc2324 күн бұрын
Upload a video
@rudyflores939521 күн бұрын
show it
@ronwilliamgeraldarnott5717 күн бұрын
Put some dish soap on and it will help lots 😂😂
@NasaInventions2025 күн бұрын
Wow, this looks so quick and easy! Who needs a tire shop when you have this trick?
@28704joe25 күн бұрын
People who's only tool they have ever used is a fork.
@a___________r41423 күн бұрын
It is more or less a joke ... it never will work in any way perfect! A lot of such videos ... show it only for small tires and steel rims ... and even these conditions will hardly work!!!
@garryhegarty888917 күн бұрын
My son just users a medium bench vice ,and it works both do ,,.
@FixItFast117 күн бұрын
How is that? Is it easy for him? I would like to see
@squarewheel1426 күн бұрын
We used to use a bumper jack to break the tire bead to remove tires about 45 years ago when I was more broke than I am now, LOL.
@neilgroves53424 күн бұрын
Used to do this back in the 80s WITHOUT gloves!
@lotossacramento29 күн бұрын
Всё гениальное - просто 🤙
@omarfongvillarreal172127 күн бұрын
VERY GOOD INGENUITY, FRIEND, TO GET OUT OF A TROUBLE. GREETINGS
@user-cv2bh4gj6h25 күн бұрын
You do not need a jack to break the seal just stand on the tyre and then use the cord to pull the off of the rim much quicker a tyre fitter showed me this trick way back in the 80s
@HeidiLamb-i4y16 күн бұрын
Good example of how to make a file a multi use tool. Kind of like chisels. They make excellent screw drivers. Right?
@flashsushi184324 күн бұрын
Anyway to balance the tires without using a balancer?
@user-ms7um1ge5j18 күн бұрын
The modern way is to pour in glass tire balancing beads, available online. I use a funnel and tube inserted into bottom of tire tire before inflating. Deliver beads to bottom of tire. Keep beads out of bead sealing area. I got a small bucket of beads, motorhome to do. It came with chart of tires and measuring cup.
@sidjames582725 күн бұрын
Somebody please get this man a valve stem remover
@a___________r41423 күн бұрын
no ... that's the advance notice - in the next video the tire change will only be done with scissors!
@НиколайИванов-с8ъ27 күн бұрын
Посмотрев как специалист завязал "бабий" узел на верёвке , понял бессмысленность дальнейшего видео....
@alanm893225 күн бұрын
Such a shame you didn't watch for another 30 seconds... I will certainly be trying his method. (Obviously with a _man's_ knot). You also missed him using a file as a tyre lever, which I'm sure would amuse you!
@user-fk6ku3hy5f25 күн бұрын
@@alanm8932 Как жаль что ты не живёшь рядом 😂 , я бы тебе показал как разбортировать колесо обычной лопатой. Это занимает пол минуты времени, безЕбли верёвками😂. Или обычным металлическим уголком и кувалдой бортируется грузовые колёса..
@modrisadijans38324 күн бұрын
@@user-fk6ku3hy5f Да просто киркой и ломом отжать . Видео англичанина умом не блестит.
@olegkusmin972023 күн бұрын
Без проблем сами делали. Ничего нового
@USCG.Brennan5 күн бұрын
You should lubricate the edge of the rubber tire with soapy water to make it slip off easier.
@geoffreycurtis130727 күн бұрын
A minute ? Check the length of the video and actually it’s a very clumbsy way in my opinion
@GordonMilliord25 күн бұрын
Do you have a better way? I'm waiting.
@Guvament_bs23 күн бұрын
@GordonMilliord to break the bead I used to put the wheel under the car and jack up using the cars weight rather than the rope. If you have a flat tire you must have a car.
@ГеннадийЦиклаури23 күн бұрын
Дурью мается.
@robbynv990023 күн бұрын
Put the tire between your ass cheeks and fart.😂
@Игорь-е4ч5м28 күн бұрын
Я всё ждал, когда же он разожжёт костер и начнёт танец с бубном вокруг него!
@SmokingPatBlueSky-hy4pl25 күн бұрын
😂❤😂🎉😅😊
@БорисРамазанов-у5е28 күн бұрын
Пока разблокировал, диск поменял цвет😂
@СергейСуховаров-к2г26 күн бұрын
Да ещё и отвёртку поменял на без ручки.
@guillaumedurand134226 күн бұрын
thanks you for the tips ! : )))
@ActionMenWorldPeacekeepers6 күн бұрын
I got a tip for everyone watching just take your car to a tire shop it's quick and easy and bring your own cheap tires you found on Walmart
@zooknz171123 күн бұрын
Surprised the file didn't break in half. Try a tire iron or flat piece of non-hardened steel. A valve core remover is a good investment as well.
@0557728 күн бұрын
Если шине 15 лет, то она так прикипает к диску, что на шиномонтажке снимают долго. На видео новая и мягкая шина, а с грубой помучаешься.
@Gary-G3118 күн бұрын
3307 - как бы не совсем новая :)
@АлексейБудихинКүн бұрын
@@Gary-G31как бы судя по остатку протектора - не совсем старая😂😂😂
@mattc622619 күн бұрын
It works but if you pinch the tread part too much you can get an air bubble and the tire can blow while driving.
@Владимр-е6л27 күн бұрын
Если у меня... За пять шесть лет колесо прокалываю.. Оно так закипит........ Никакими донкраиами...только ведешкой отмачивал и кувалдой....
@brucerobson876723 күн бұрын
Never use a file as a lever! It is brittle and will snap, possibly causing serious injury.
@mkrp420 күн бұрын
@@brucerobson8767 The entire video is BS; this tire had been removed before the video
@ruslankeller38627 күн бұрын
Огромное спасибо!! Крепкого здоровья тебе!
@Aleksey-Nosko27 күн бұрын
Так бескамерные покрышки превращают в камерные👍
@northotagogolf18 күн бұрын
I also used a car jack, but rather than use a rope, I put the jack on the tire as above, then just "jacked up" under the cars tow-bar.
@dinganejacob187819 күн бұрын
Wow 👌 👏 😍
@FixItFast119 күн бұрын
🔥💪 Yessss
@lisiatepalu773725 күн бұрын
Thankyou for your sharing information Thankyou
@JesusReidosReis-725 күн бұрын
Parabéns!você ganhou + um inscrito .
@juvillace2222 күн бұрын
Good idea 😮
@diversity273924 күн бұрын
Thanks
@BackUp-z4t24 күн бұрын
Well done.
@johnlennox-pe2nq25 күн бұрын
put the wheel and tire under your vehicle jacking point; insert the jack so that its pushing down on the tire wall now turn the jack handle - it will push down on the tire wall and break the seal due to the weight of the car. Now plin the seal gap push, a peice of wood, a spanner or some wood or lever the plastic to hold the gap in place; around a 1/4 is now released. let the jack off, and do the same to next section of the tire wall; eventually the full seal will be completely broken; Remove it, and use washing up liquid to take the tyre over the rim, and full removal
@JohnSmith-un9jm25 күн бұрын
Forget it; I don't have a lighter
@allangray632019 күн бұрын
Or scissors
@mehmetarslan261928 күн бұрын
emeğe saygılar güzel fikir
@edwardmiller575424 күн бұрын
Very very smart choice
@tasoslogo179923 күн бұрын
BRAVO
@FixItFast123 күн бұрын
🤗🤗🤗🤗❤️
@dietmarharens3811Ай бұрын
Vielleicht muss man die Innenseite des Reifens auch noch abdrücken, damit man den Reifen richtig hochziehen kann !
@FixItFast1Ай бұрын
Absolut wahr! Dieser Trick funktioniert in beide Richtungen! Danke für deinen Kommentar, mein Freund!❤️
@lodreipeina1325 күн бұрын
Chłopie! Co ty wyprawiasz? Odpuść. Pilnikiem po feldze? Nawet po wódce bym tego nie wymyślił. 🤣
@VE3UET25 күн бұрын
2 different wheels used is this show, but very good Ideas, I suprise the guy didn't take advantage of the centre of the rim to remove and install the tire
@FixItFast125 күн бұрын
Yes, my friend, you are very attentive! Everything is as you said, but everything is done at home
@michaelperez27726 күн бұрын
Une intelligence de génie 👍💪😉
@AlekseiGorcheninN7827 күн бұрын
Молодец!
@kamaljitsinghattalia25 күн бұрын
Fantastic too GOOD BRAIN WORK FANTASTIC FANTASTIC FANTASTIC TOO GOOD THANK YOU VERY MUCH MUCH FOR THE TEACHING
@FixItFast125 күн бұрын
Madly praaaad for your such laudatory comment! Thank you friend! hugged
@NoelShelley24 күн бұрын
Make 4 wedges cut from a bit of 2" x2" timber and use a 4Lb lump hammer, off in seconds, then use a pair of 20" tyre levers and soapy water. Mark valve position on the tyre for refitting. Simples ! Not so easy on an old rim that may be rusty though.
@deanyanko332620 күн бұрын
that's a good point you must scrape old rust away around inside rim bead and use rim sealer too.
@hfBMW26 күн бұрын
motorcycle tires are replaced every year. upwards of 19,000 miles I have added to the motorcycle. soft tires wear faster than car tires. maybe this trick can help me
@fidelcatsro694811 күн бұрын
Its been over 100 years..We meed to reinvent tyres that are easier to fit and dismantle
@neilscarlett3416Ай бұрын
This trick is perfect for DIY enthusiasts or those looking to change tyres faster than an F1 team
@FixItFast1Ай бұрын
This is really true, my friend! Thanks for your comment! Tell me if you managed to repeat this trick!🤗
@ELIJAH-BLAIN26 күн бұрын
Brilliant!
@INTERNA926 күн бұрын
Thanx
@سجادبلوچ-ن2ض7 күн бұрын
احسنتخیلیخیلیتشکر❤❤❤
@johnzdrazil214025 күн бұрын
Wicked Cool!!
@sircaptainchaos238826 күн бұрын
You made hard work of that
@ВалерийЯкушин-ъ3й24 күн бұрын
Молодец! Здорово!
@musicD.A.27 күн бұрын
Now after remove how you put the new tire on ???
@логик-ц3ю26 күн бұрын
Умница 🎉🎉
@randybarnes845425 күн бұрын
I always use my 25ton hydraulic log splitter and some short square steel tubing
@deanyanko332620 күн бұрын
I just call big mama to step on it ha ha
@miodragmarkovic330424 күн бұрын
Bravo
@cigknowles754224 күн бұрын
Ok if your using old wheels and tyres off the scrap pile , or in an emergency but thats about it, modern alloy wheels, i don't think so
@SergeyKolbasov-qz1ox2 күн бұрын
Главное балансировка колеса, а поменять шину на диске не проблема.
@JerzyAftyka28 күн бұрын
Gratuluję pomysłu hej
@arthurdunn145222 күн бұрын
Jack fell off at 4.18,not vey efficient, though I thought the comment about the mark on the tyre and rim was excellent. Australia 🇦🇺
@PabloCosta-xu3my26 күн бұрын
Que bueno amigo
@ELIJAH-BLAIN26 күн бұрын
I always just put the tire under the truck frame with screw jack on it. It worked but but not easy.
@jurgenalles41423 күн бұрын
Die Idee ist gut.Doch entscheidend ist später das Wuchten😊