got me one, but you have to handle those very carefully or else you ruin your tire. If the tire is really tight you run the risk of damage (tearing off the rubber protection off the steel threads.... which in turn damage your inner tire).
@ospreymanlott79754 жыл бұрын
I've used it quite often, no way you will damage the tire using this
@tony10speed4 жыл бұрын
I tend to agree with you as do some others. However, used properly and with care, it should perform quite well without damage to the tire. Regards, Tony
@davidlevine71644 жыл бұрын
I've been changing tubes for decades, but I got a new wheel and after pinch flatting 3 tubes trying to get them on this new wheel, I bought a tire bead jack to carry in my back pocket along with my pump. I watched my bike mechanic use it and he was able to install a new tube easily.
@tony10speed4 жыл бұрын
Anything you saw him to that might add or not included in this video? Thanks, Tony
@EleniLixourioti4 жыл бұрын
I have learned so much through your videos, thank you for sharing your knowledge and experience with strangers from across the globe!
@tony10speed4 жыл бұрын
I hope to continue to pass on my experience. Thank you. Regards, Tony
@TheBlatt63 жыл бұрын
Nice to see the 1st Cav patch.
@tony10speed3 жыл бұрын
1st Cav, Medivac, 1971-1973 at the end of the Vietnam War. Our motto: "So Others May Live." Regards, Tony
@@TheBlatt6 Great to hear from you. Regards and be safe, Tony
@henriclouisemeldgard50484 жыл бұрын
I used to start tire mounts at the valve and usually had this problem and some pinched tubes. Switched to finishing at the valve and eliminated almost all tight tire mounting problems. If you start at the valve it prevents the tire from seating into the center rim groove and maximizing the slack required to slip tire over the rim.
@tony10speed4 жыл бұрын
You are correct. However, when using the Kool Stop Tire Bead Jack, I've damaged the valve a number of times when ending at the valve itself. I have some new neat version of Bead Jack (a smaller version and not from Kool Stop) and we'll test them starting away from the valve and starting at the valve and put that on video. But your comment is very well taken. Thanks and regards, Tony
@berlin36moto3 жыл бұрын
Found this especially true when mounting tubeless tires. (conti 5000 TL opposite the valve was almost impossible, towards and ending at the valve gives you a few mm more) Learned 30 years ago to never end at the valve - but now I changed.
@sdgreg79324 жыл бұрын
Thanks Tony. I had a very hard time getting some new Continental 5000s on my rims recently. This tool looks like an excellent possible solution. I’ll order one immediately. Don’t have many flat on my riding routes but would be worth the money for the two or three sets of worn out tires I replace each year at home.
@tony10speed4 жыл бұрын
When you use it, go slow and be careful not to damage the tire side wall. If you want to carry it with you on a ride just cut off about 1/3 of the handle. Let me know if you have any questions on it's use. Regards, Tony
@jasonfarrar15133 жыл бұрын
I was distracted by that indi fab next to you. Dream bike!
@tony10speed3 жыл бұрын
Wait until you see my 1990s Litespeed Classic! In mint condition with new 1990s decals from Litespeed. Will post it soon along with pictures of the inid fab. Both titanium vintage classics. I obtained the custom indi fab when Independent Fabrications moved to New Hamshire. We worked together to spec out the size. I then added all components, a light speed carbon fork (which I happen to have in my workshop) and more. The 1990s Litespeed Classic was a triple which I converted to a compact (new BB, crankset, pedals and seatpost). Fits like a glove. More to come in an up coming video. Regards, Tony
@jasonfarrar15133 жыл бұрын
@@tony10speed oh that sounds delicious! Did you use 90’s components? J
@tony10speed3 жыл бұрын
@@jasonfarrar1513 Not completely. I used what I had available in my shop. A NOS vintage Shimano spindle bottom bracket, an Origin 8 170mm crank (I converted the bike from the original triple to compact double which I prefer) that also fit the spindle bottom bracket, and replaced the Ultegra brakes with Shimano R-7900 dual pivot brakes which are far superior to the original Ultegra (replaced them for safety -allowing better braking). The wheels had been already replaced recently with excellent Bontragers front and back. The rest of the bike was cleaned, lubricated and added new decals. The idea was not to restore it completely to it's original but rather set it up for me to ride in *comfort and safety*. Regards, Tony
@johnshadle48176 жыл бұрын
After a lot of problems with installing 700x25 Gatorskins I found that the The Kool Tire Bead jack works pretty well, but there's another problem. When you pry the bead on, the part of the bead opposite begins to pop out again. You can chase that space clear around the tire. What worked for me was to use a CABLE TIE to grip around the tire where it pops out, so it doesn't pop out again. I've seen a wire wrap used to this purpose. The tight tie is not-removable, so you have to cut it off when you're done. I keep a single edge razor blade in my tire kit along with the tire levers. The Kool Tool carries well in my small triangular frame bag
@tony10speed6 жыл бұрын
John Shadle - Haven't had that problem but your solution sounds reasonable. Thanks John. Regards, Tony
@tony10speed5 жыл бұрын
Put on the tire by hand as far as your can. Then finish up with the Kool Tire Bead Jack. That should eliminate the "chase."
@keithguiste26594 жыл бұрын
Kool STOP
@Martyn3834 жыл бұрын
@@tony10speed in place of cable ties, use a toe strap from a cycle pedal, few use the old style toe clips now so the local bike shop may have them hanging around ? handy for other jobs as well
@tony10speed4 жыл бұрын
@@Martyn383 Thanks Martyn. I also bought a bunch of Velcro strips at Lowes, use to tie up cords or garden hoses (about $5). They also work great. Regards, Tony
@jimwright3253 Жыл бұрын
As someone with arthritic thumb joints, the Tire Bead Jack shown is just the thing to allow me to get my tire back on the rim without stressing my thumb joints. The little plastic tire irons that I still use to get the tire off the rim to fix a flat still are the best tool for that, but they are terrible for getting the tire back on after. My only complaint about the Tire Bead Jack is that it is a bit too large to fit in my seat bag. I ended up having to use velcro straps to attach it to my extra bottle cage. I wonder if a smaller Tire Bead Jack meant to fit in a bike seat bag could be made? perhaps something similar to the original, but with a shorter handle, or a handle with an additional joint allowing it to fold?
@tony10speed Жыл бұрын
You could cut off part of the handle of the Tire Bead Jack so it will fit in your saddle bag. If your tires are 28mm or less in width, you can try the EZclincher tool (ezclincher.com). See: kzbin.info/www/bejne/iqrZeqmcna2JgLc Let me know if either solution works for you. Regards and safe cycling, Tony
@johnvalderama5223 жыл бұрын
thanks for sharing, it a great tool installing road bike tires. some tires are difficult to install. i will definitely get one. have a safe ride always.
@tony10speed3 жыл бұрын
Also consider the EZ clincher tool which is small enough to fit in your saddle bag. See: kzbin.info/www/bejne/iqrZeqmcna2JgLc&ab_channel=TonyMarchand Regards and safe cycling, Tony
@jj95east3 жыл бұрын
Subscribed based on your energy. Stay healthy friend.
@tony10speed3 жыл бұрын
Thanks for the complement. Regards and safe cycling, Tony
@cwmson83814 жыл бұрын
TM - thank you for the video and hope you are staying well. I got a Kool-Stop tire bead jack, which saved me after pinching holes and gashes in multiple inner tubes, in addition to scratching up my aluminum rims trying to use metal levers. I don't bike a lot, and I finally had to replace my old (early 90's) Mitsubishi City Slicker 26 x 1.50 road tires on my old Trek 930 Singletrack mountain bike / MTB on 26" Trek Matrix Single Track wheels. Not sure if tire dimensions have changed, but I had a super tough time getting on the new Kenda Kwest K-193 tires. Have a spare set of the same wheels with 26 x 2.10 knobby tires that are also tight, and the Kool-Stop worked for those also, but the jack's movable lever could use a bigger bend to get around the bigger tire - had to deflate the inner tube and getting over the bigger tire wasn't easy, but still better than using levers. I used spring clamps to keep the other side of the tire bead from slipping out while I used the jack, but I agree with another comment about using cable ties for when away from home and having a small knife to cut it off when done.
@tony10speed4 жыл бұрын
I was able to buy a bunch of "removable reusable" zip ties on Amazon. Then there's no need to cut ties off - you press part of the tie, it comes apart and can be reused. Some tires and wheel are just harder to manage then others. Before I buy (in my case build) a new wheel, I always look for a deep central grove in the rim. That way, on can shake the bead into the center rim as you install the tire, which makes a little more room (slightly smaller circumference) to help me get that last part of the bead in. Then I make sure all the air is out of the inner tube, and either by hand or with one of my tools (Crank Brothers Speedier Lever of Kool-Stop), get the rest of the bead on. Regards and safe riding, Tony
@cwmson83814 жыл бұрын
@@tony10speed Good idea with the reusable ties. I guess a velcro strap would work also. Thanks again.
@bubsblues59404 жыл бұрын
I wish I had had that tool the other night while installing a particularly difficult new tire. I broke two basic plastic levers and destroyed an inner tube in the process. What finally did the trick - believe it or not - were two common stainless steel kitchen spoons. The rounded handles were sturdier than the plastic and didn't risk puncturing the tube, and the bowls of the spoons slipped easily under the spokes and worked like the hook ends of the levers. Not ideal, perhaps, but pretty good in a pinch.
@tony10speed4 жыл бұрын
Not a bad method. They do may stainless steel tire levers (I have several pairs), but I'm always worried about pinching the tube. You can also carry the Kool Stop Tire Bead Jack with you in your saddle bag by cutting the handle to about 1/2 its length. Regards, Tony
@sophiescyclingandwalkingch42944 жыл бұрын
Great tool, it made the job easy😁 thanks Tony.
@tony10speed4 жыл бұрын
Glad you found it useful. We will have a new video coming out on a "min-version" of the too that you can store in you saddle bag. Regards and safe cycling, Tony
@sophiescyclingandwalkingch42944 жыл бұрын
Tony Marchand thanks Tony you keep making them. I’ll keep watching them 👍🏻
@ospreymanlott79754 жыл бұрын
Since I got Williams Wheels there's absolutely no way I can get the tire back on without this. I carry it in my camelback side pocket. In fact, its almost impossible when I get a flat to pry one side of the tire off with any kind of lever. So I have to remember to squeeze both sides of the tire to the center of the rim and even then its very hard to get a lever under the tire lip. That might be a useful vid Tony, getting a tight tire off to get the tube out. Thanks for this vid!!
@tony10speed4 жыл бұрын
Good idea. Thanks, Tony
@icarusicarus90392 жыл бұрын
Thanks for d the video, Question: Does it work for a rim 29 and tire size 2,25?
@tony10speed2 жыл бұрын
The Kool Stop Tire Bead Jack is best for clinchers up to 32 mm. Most find it difficult to use on wide tubeless tires (and may damage the rim tape if incorrectly used). The best method for installing tubeless tires involves moving the bead to the center of the rim: kzbin.info/www/bejne/ZoCYYZxuqqiknJY and kzbin.info/www/bejne/jIa0c4aVgNqnfKc Although I did find a video where the Kool Stop was used for Gold Race 29er wheel set: kzbin.info/www/bejne/g4fIc56VfMyXl6c Regards, tony
@landryhc4 жыл бұрын
Tony - thanks for showing the youngsters that an "experienced" guy can still learn (and teach). I bought a tire jack after seeing your other vid (using an actual tight tire) - I figured there had to be an easier way. Whatever happened to kevlar beads? Those were much easier to mount.
@tony10speed4 жыл бұрын
The beads are the parts of the tire that grip the rim when the tire is inflated to keep the tire in place. At lower price points, tires come with wire beads made of steel. I use Continental Gatorskin with wire beads. They don't seem any more difficult to put on then Kevlar. As you spend more, tires feature flexible beads made of synthetic materials, such as Kevlar, a DuPont material also used in bulletproof vests. Tires with flexible beads are called "folding tires" because the beads allow the tire to be folded (wire-bead tires can only be folded partially). They're also called "Kevlar bead tires." Besides saving weight, Kevlar beads usually make tires a bit easier to install and remove, too. How to choose: If you want the best, get folding tires because they're lighter, which makes your bike easier to ride. If you want a good tire at a sweet price, you can usually get top tire designs for less simply by buying the version with wire beads. Regards, Tony
@fredlast45475 жыл бұрын
I find some washing up liquid on the rim helps a lot.
@tony10speed5 жыл бұрын
You're correct. It does. But if you get a flat out on the road, you'll need to carry some with you. Any ideas on how you might carry some along? Regards, Tony
@AndrogyneMichinaga4 жыл бұрын
I have some washing up liquid in an old medicine capsule bottle.
@jonathanhawker74542 жыл бұрын
Hi Tony - presumably even if you carried this or an EZ Clincher shown in your other video, neither could get a tight tire off the rim so you'd have to carry a lever too? And do you know if these are safe to use on carbon rims? Many thanks for your wise advice
@tony10speed2 жыл бұрын
Yes, you would need tire levers for removal when carrying the Kool Stop or the EZclincher for tire installation. Using a wide thin PLASTIC lever such as those by Pedro (yellow) or Park 2 Carded Tire Lever and always, taking your time, should not damage the carbon rim. Some carbon fiber tubeless rims an be a challenge. Here's a video that may help: kzbin.info/www/bejne/mGfGdaKErsupsMk I, myself, stay away from metal tire levers although I have several types in my tool box. Good question. Regards and safe cycling, Tony
@TiFiber5 жыл бұрын
Great video of a nice little tool and do you think it would be safe to use with carbon fiber wheels? Thanks.
@tony10speed5 жыл бұрын
They do indeed work with both carbon rims and tubeless tires, but like all tools, can be dangerous/damaging in the wrong hands. You don't need to use a bead jack to break a carbon rim, after all. I've seen it happen when plastic or metal tire levers are used. The bead jack is meant to center the tire in the rim for easier installation, but be gentle and go slow. My preference with carbon rims is to find a combination of tire and wheel that allow installation by hand. Regards, Tony
@mcring543 Жыл бұрын
End at the valve stem. This provides more slack since both beads can sit in rim valley where you started.
@tony10speed Жыл бұрын
You're absolutely correct. However, with the Tire Bead Jack, maybe due to it's large size, there is a great chance of damaging the valve as you get close to it. This and fact that it's large size prevents it from fitting in ones saddle bag are a disadvantage to the Tire Bead Jack. The EZclincher is a smaller tool, allow better control, and is less likely to damage the valve. Take a look at the following video and let me know what you think: kzbin.info/www/bejne/iqrZeqmcna2JgLc Thanks for your comment, Tony
@mcring543 Жыл бұрын
@@tony10speed Right. I meant that the extra slack might be enough to not need a special tool. Thanks. I appreciate your videos.
@reecerobinson60664 жыл бұрын
Thanks for the video Tony. I had some new Conti GP 4000S tires a couple years ago that I couldn't fully install onto my new fancy deep set wheels. Out of fear of damaging them I took them to the bike shop and they whipped out a tool (I think they called it a bead puller) but my guess is this is what they had. I'm going to order one of these so I'll be ready when we can get back to group rides.
@tony10speed4 жыл бұрын
Be sure to practice at home so you're ready to use the tool when necessary. Good luck and have fun. Regards, Tony
@videotowatch20005 жыл бұрын
Schwalbe tire levers are the best for this application and they are standard size to fit in a saddle bag.
@tony10speed5 жыл бұрын
Mixed results however on difficult tires. Watch for an up coming video on a similar product in 2 weeks. Thanks for your input. Regards, Tony
@buckettraveler83984 жыл бұрын
Just ordered one. I have a wheel set that seems impossible to get any tires on. Thanks for this
@tony10speed4 жыл бұрын
Just one word: It works on most tires and rims but there are a few combinations tires/rims that are still tough. Luckily the tool is not expensive. Let me know how it works for you. The feedback help me and our viewers. Regards, Tony
@buckettraveler83984 жыл бұрын
@@tony10speed will test it in a few days, don't have a reason to take my tire off right now
@ZillaYT5 жыл бұрын
It's Koolstop, not Kool Tool correct? Or is yours a different brand.
@tony10speed5 жыл бұрын
There are several makes of "Tire Bead Jack" out there. Mine is ancient, made by Simson. Another is the IMFUN Bike Tire Lever that does the same job. The most commonly sold is from Koolstop as you mention. I'll put a notation in the title and description. I appreciate your input. Regards, Tony
@marksondag208510 ай бұрын
I have the Tire Bead Jack and it's a life saver. You're kidding about packing that in your pocket though, right? That's a shop tool only for me.
@tony10speed10 ай бұрын
Some individuals cut off about 1/2 to 2/3 of the handle and carry it incase of a flat on the road. I will give it a try myself. You want a tool to take with you so you don't get stuck on the road. Also consider a similar tool called the EZclincher: kzbin.info/www/bejne/iqrZeqmcna2JgLc Regards and safe cycling, Tony
@flpirate455 жыл бұрын
I'm getting one or two next week. Thanks
@tony10speed5 жыл бұрын
You're very welcome.
@manoz61942 жыл бұрын
I've encounter a combination which I think even this can't even solve. Mavic allroad wheels and a tubeless Schwalbe almotion tyre. Even the first bead was difficult to get on and with ordinary levers more than 1/4 of the tyre won't go in. I'm too afraid to damage my rims
@tony10speed2 жыл бұрын
You could give the Kool Tool Tire Bead Jack a try. But first look at this video and the method used (let me know if it works): kzbin.info/www/bejne/jIa0c4aVgNqnfKc
@pokemon5552223 жыл бұрын
Wow I wish I knew this existed when I was regulalrly changing from a road to a trainer tire last winter, my Schwalbe Pro One tyres were such a pain to get on but this porbably would have made life so much eaiser
@tony10speed3 жыл бұрын
You also maybe interested in the EZclincher for tires upto 28mm. It works on the same principle but is smaller and can fit in your jersey pocket or saddle bag. See: kzbin.info/www/bejne/iqrZeqmcna2JgLc&ab_channel=TonyMarchand Regards, Tony
@fouresterofthetrees2873 жыл бұрын
Can this tool handle larger rims/tires, like 40 mm?
@tony10speed3 жыл бұрын
Should work fine following the tips from Larry Grimme: kzbin.info/www/bejne/g4fIc56VfMyXl6c&ab_channel=LarryGrimm Regards, Tony
@Andrew-on5do6 жыл бұрын
I ride a cannondale slate and the tires on this thing are incredibly difficult to get on. Picked up one of these from my lbs.
@tony10speed6 жыл бұрын
Richard Swagger - should work, just a little bulky to carry. The Var tire lever is smaller and does the same thing, but is not as easy to use. Let me know how you make out. Regards, Tony
@brianbreighner46245 жыл бұрын
I ride a slate as well and I agree, the Panaracers are extremely difficult to seat onto the Mavic rims. I'll be buying this tool.
@ytwos13 жыл бұрын
For me, new clincher tires are sometimes a pain. I came from a bicycle repair family and have been doing it every now and then since small. This tool would certainly help. But when the same tire is on a rim for some time reinstalling it after a flat (on the road) usually is easier. Tire is now round and often a bit more plyable. This tool is not for on the road. Bring some simple plastic tire lifters. Cheap and cheerfull.
@tony10speed3 жыл бұрын
Yes that's true. But if you want something to take on the road, take a look at the EZclincher for clinchers 28 mm or less - in the video below. This works similar to the Tire Bead Jack but fits in your saddle bag or jersey pocket: kzbin.info/www/bejne/iqrZeqmcna2JgLc&ab_channel=TonyMarchand Regards and safe cycling, Tony
@joescheller66806 жыл бұрын
dont know much about byck tires but on regular tube type the valve stem end is always last as to not damage stem????
@tony10speed6 жыл бұрын
That is true Joe. But with the Kool Tool, I try to stay away from the valve as I finish up the tire. The Kool Tool may damage the valve of the tube as you move it around that area. But it is a large tool with lots of force, so it works no matter where you finish installing the tire. Good question. Thanks, Tony
@davewyman4 жыл бұрын
Joe Scheller I always start with the stem. It can’t be damaged if it’s inserted first, before mounting the rest of the tire.
@VictoriaAlfredSmythe4 ай бұрын
Simson Tyre Mate
@tony10speed4 ай бұрын
Tire Bead Jack from Kool Stop, Simson or IMFUN Bike Tire Lever essentially the same as noted in the video discription. Here in the US, we call it the Kool Stop but in the UK, it's the Simson.
@jake309665 жыл бұрын
Would this work for MTB tyres and wheels
@tony10speed5 жыл бұрын
It should work on MTB tires with tubes. Haven't used it with tubeless tires myself but a few individual have with success. Anyone tried the Kool Tool with tubeless?
@MTBXCSKI655 жыл бұрын
I'm having trouble using this tool to install a Bontrager XR2 Team Issue TLR MTB 29 x 2.2 on a rim. The bead jack is too small for the large tire casing. My 27.5 tires also have large casings. Maybe it would work better on my 26er because the casings are smaller. Road tires are smaller so it works fine on those.
@tony10speed5 жыл бұрын
Thanks Gary. That's good to know. Regards, tony
@jamesone60986 жыл бұрын
I put it in my Jersey pocket if I'm riding my wheelsets that have really tight tires on them. It's better to have it and not need it than to need it and not have it and end up stuck out on the road walking.
@tony10speed6 жыл бұрын
I agree. Thanks James. Regards, Tony
@jamesone60986 жыл бұрын
Thank you Tony for your informative videos.
@tony10speed6 жыл бұрын
Glad I can help. Please subscribe if you haven't already. Regards, Tony
@finnatwood72403 жыл бұрын
Dont forget to stretch the tire before hand
@tony10speed3 жыл бұрын
Tires are very difficult to stretch. What is your method if you don't mind me asking?
@randallsmith78854 жыл бұрын
This is certainly better than cutting a tube with a tire lever...
@tony10speed4 жыл бұрын
The Kool Stop Tire Bead Jack is my last resort on difficult tires. Be careful not to damage the wide wall of the tire as you move around to install the bead. Go slow. You can carry the Kool Stop tool in your saddle bag by cutting the handle end in half. Regards, Tony
@informedchoice2249 Жыл бұрын
That was an easy rim. Try it on a 26" Marathon on a mountain bike wheel, then I'll buy it!
@tony10speed Жыл бұрын
I will have to leave that to you since I don't have a 26' Marathon to work on.
@rodrigolucia75406 жыл бұрын
Really cool gadget, however I don't think it is very practical to carry it, it's more for the shop
@tony10speed6 жыл бұрын
Agree. But if it takes the Kool Tool to put the tire back on in the shop, what happens if the rider gets a flat out on the road? Although I use the Crank Brothers Speedier Lever which easily fits in my saddle bag, one of our club members swears by this tool and always carries it with her on rides in case of a flat. Only practice changing flats will allow one to know what tool(s) (if any) work best for them. Thanks for the comment. Regards, Tony
@rodrigolucia75406 жыл бұрын
Tony Marchand I thought of that, if you need it to put it then on the road with out it good luck hahaha. Regards from Spain!
@tony10speed6 жыл бұрын
Rodrigo Lucía Totally agree. Enjoy, Tony
@m.amonroy44653 жыл бұрын
When you know how to install a tire, you don't need any tools just your bare hands, I can install the tightest tire using only my hands, just move the tire bead to the center of the rim.
@tony10speed3 жыл бұрын
You are right that most can be installed by hand. But I've come across a few (a Continental Gaterskin tire on a Victory Rim) where the center grove is minimal and some tool to assist is a help. Also, some individuals like my daughter, have small hands and may not have the your strength. So, all I can say is keep up the good work. Regards, Tony
@vinnerdinner Жыл бұрын
that looked like a very easy tire to install. better to show a difficult one
@tony10speed Жыл бұрын
Gatorskin wire bead tires are notorious for being difficult to install. It looks easy because of the use of the Tire Bead Jack. How difficult depends on the tire/rim combination with a Gatorskin tire/Victory rim being the most difficult. The Kool Bead Jack was the only one to get the tire on the rim. Unfortunately I did not have that rim available to demonstrate since it was in use by a client out on the road and I don't think he would have appreciated me borrowing the wheel in the middle of his ride. You might want to try out the Kool Bead Jack on some of your difficult tire/rim combinations and let me know what you think? We can all learn by other's experience. Regards, Tony