Thank you for actually giving real suggestions to determining the problem! My washer company site only had dumb suggestions like, ‘is the door closed?’ ‘Is the setting on low or delicate?’ Useless! But your info is so helpful. Thanks again!
@audreymeyer56163 ай бұрын
There is a latch inside the door. If the door is not properly shut then the dryer will not run, or washer will not start it will be in a standby mode. I’m curious, what else did they suggest?
@nothankyou5524Ай бұрын
@audreymeyer5616 normally, there's a button like you find on a fridge that turns the light on and off. A new type dryer probably has some type of latches, I would suspect. How did you make out fixing your washer? They're not that complicated if you have the time to just sit and look at them from the backside. About 15 minutes and a particular purpose and prior instruction, and things may start to fall into place. I hope you gave yourself a chance to fix it. Even if you got stuck, you've not failed. You've just learned what you didn't need to be concerned with regarding the repair. If you did or didn't take a shot, you learned more than you know. Next time, you'll see much improvement. Best wishes. Best of luck. You got this, I can tell!!!
@googleuser8683 жыл бұрын
Switch broke years ago. Twisted the wires together and bypassed the switch. Clutch got weak so put an extra washer by the spring and cleaned the oil leaking from the transmission out of the clutch drum with brake cleaner. Had a spring break that helps stabilize the tub on the spin cycle. Twisted a new hook on the end and reattach it with a short loop of coat hanger wire. Lots of stuff has broken on our old Roper washing machine but haven't had to buy a part yet. Lol Had to buy a new drum belt for the matching Roper drier and the control dial has been shot for years. Just hit the start button and it still works like it has since new. Takes forever to dry a full load of laundry. Heating element glows and the ducts are clean. Believe it had poor air flow from the get go. Glad there are plenty of do it yourself videos to help me keep these low quality Ropers going. Miss my old bare bones basic GE washer and dryer. Oh. And the adjetator likes to occasionally eat clothes. Down at the bottom of it are four fins with a small gap over the base plate that catches clothes and has ripped more that a couple fairly new shirts.
@rickybishop81 Жыл бұрын
Washing machine only fill and drains won’t spin
@hughjaybeats41265 жыл бұрын
Top load washer won’t spin: 1. Defective lid switch 2. Worn motor coupler 3. Broken or worn drive belt 4. Damaged stator/rotor 5. Worn clutch 6. Defective drive motor
@explorewithping57574 жыл бұрын
1. checked, good lid swith 2. checked, good motor coupler 5. good clutch
@sheilasmith11093 жыл бұрын
Dear Hugh Jay. How doe you determine what exactly is wrong? Re your answers, is it: All the above? Or which one(s), please! How does one tell which ones are defective?
@leakecece969311 ай бұрын
Bless you ❤️🙏🏾
@ammoalamo64852 жыл бұрын
My first washer and dryer (and refrigerator, upright freezer, and chest freezer) all lasted "forever", call it twenty years or more. I still have that first washer and dryer out in the shop, doing yeoman service as sturdy metal-topped tables with storage room inside, and a two good electric motors and pumps should I ever want to DIY something with them. The wife just wanted something new, with modern features. Fine with me; we certainly got our money's worth out of the old set. I think for the washer it cost about two-fifty a month, and a little less for the dryer. Small change, anyway. The new one we bought back then just died after a piddling five and a half years - cost about ten bucks a month. Still cheap, but not as cheap as the good old daze. I guess the manufacturers realized they could not stay in business building the type of quality products that would last for twenty years or more.
@ImahSillyGirlАй бұрын
EXACTLY. I'll fix my old stuff as long as I can. I'm afraid it might be the motor this time though. 😬
@Steef12 Жыл бұрын
My washing machine won't spin and/or start cycle. I can hear/see the shift actuator move back and forth and then the motor tries to spin and gets like maybe 1/4 turn and stops. It will do this a few times and then just stop. Do you have any idea?
@Steef12 Жыл бұрын
I had a replacement clutch kit and the parts fit too tight. I greased them a little bit and it seems to have fixed the issue.
@cadavher6 ай бұрын
Ah, this is exactly what mine is doing. My fault honestly, I overloaded it all the time. Will look into getting a new clutch!
@martik778 Жыл бұрын
My top load whirlpool 20 year old washer doesn't seem to extract as much water as it used to. I replaced the motor to tranny coupling which was partly broken and measured the spin RPM at ~550 rpm. The clutch seems ok, not too worn - anything else?
@gojackets48945 жыл бұрын
My Maytag washer with a stator type of motor had a little water at the bottom of it. Realized it was the bearing, problem it is you can't just replace the bearing it requires the whole tub and bearing assembly. But it was actually easier to replace than I thought. Used to have another type with the coupling, you can tell when it's the coupling if there's little bits and pieces of plastic down below and it's also pretty obvious when you lift a washer up you can actually see the coupling with the prongs broken off.
@zdflores4 жыл бұрын
I have a GE, my agitator does not spin but the bottom portion does as it’s 2 parts. Agitator is loose but unlike other videos where they take out the fabric softener cup and the plastic to get to the nut. I cannot get the plastic off as the ridges are worn down and almost impossible to get off. I’m pretty sure the agitator is just loose but I have no idea how to tighten it
@kimcostello63253 жыл бұрын
Help! Will agitate but stops before rinse and spin. couplers? are good and replaced lid switch
@odarrien2 күн бұрын
I have a White-Westinghouse that is washing and rinsing until it gets to the "Spin" cycle. Once it gets there it just stops doing anything. Its happening on the various cycle types - delicates, regular, etc... whenever it gets to "Spin" it just stops and doesn't drain...... What might be the problem?
@bellaswan1459 Жыл бұрын
well this may not be my issue just got told its making to much noise and may not be spinning so obviously need to check but looks simple to fix. i know the belt part needs fixed just been using duck tap lol but I hope this issue isnt costly for my brothers sake lol. Thanks for these videos it has help me a lot and saved me hundreds
@jeconiaA9 ай бұрын
I got XPB100-2100s Ikon Top load washing machine made in China.The washe won't spin when loaded.What might be the fix
@niruldesilva334310 ай бұрын
Hitachi SAF 1020 mechine spinning work some times but some time it is not working what will be the issue may be timer contacts problem pease advice
@galyien5 жыл бұрын
How do you get into diagnostic mode? I remember you have to hold several buttons at the same time. These shity washers wont last more than 3 years. The luckily I have a spare washer on standby that's 20 years old. However I still want to get this fixed
@kimcostello63253 жыл бұрын
A timer? What is that part, or what controls it?
@jeffm.16563 жыл бұрын
On an LG top load washing machine, is the washplate supposed to move independently of the outer washtub, or is that an indication that the splines on the washplate are stripped ? Thanks for the videos.
@chargriggs1037 Жыл бұрын
How do you get out something wrapped around the agitator?
@nothankyou5524Ай бұрын
Slowly and carefully. How did you make out. If you couldn't get it out yourself, don't worry. You'll have at least one more chance. Life is like that. You keep getting to repeat the lesson until you've completed it successfully. Then you get a whole new, bigger lesson. I never believed in that stuff, until I started believing it. Hey, best wishes!!!
@joeperkins57203 жыл бұрын
Have a whirlpool wtw5000dw1. Spin cycle was not working. Hooked spin motor up and watched. The motor is running so I suppose it is just the drive belt. All else seems fine
@Nikhil-jj7xf7 жыл бұрын
Hii very good information thanks alot but my machine also not spin but it spin for alsmot 15 sec when I force on it Manually isit pblm with my motor?
@susansevilla20545 жыл бұрын
My Whirlpool Model LSRS100HQO won't spin and just making noise, what part should I replace?
@cristobal83673 жыл бұрын
Coupler
@susansevilla20543 жыл бұрын
@@cristobal8367 Thanks
@cdcVintage5 жыл бұрын
My GE won't spin. Just makes clanking noises and moves back and forth a little. . I put a magnet on the lid switch so I can have the door open. I gave the tumbler a little push and now it's working. What could the problem be?
@bobvance47124 жыл бұрын
Check the starter capacitor
@colleenlassie26008 жыл бұрын
Great information. I have a Kenmore 400 that will not spin.. the lid switch is clicking .. the pump is draining the water out.. Of your options in this videos, what should I look for for my machine. Thanks
@midniight6 жыл бұрын
Colleen Lassie i have the exact washer with exactly the same problem. plz let me know if you've found a solution as i will do the same if i find one.
@MikesTek6 жыл бұрын
my washer is a kenmore Elite 110.27032600 that just stopped spinning, of course it is mid cycle. It is making a humming noise that stops and starts, but no spin. the tub freely moves in both directions by hand. how do I tell if the stator is what actually went bad or if it might be the position sensor or bearing? I don't want to order a lot of parts i don't need.
@lavernlyons64796 жыл бұрын
Mikes Tek I have the same problem
@doloresmontijo78905 жыл бұрын
Same
@Chuffin_ell5 жыл бұрын
Dolores Montijo water still in tub? If not, it's the motor coupling
@victoriakling75212 жыл бұрын
Amanda model NTW4516FW2 wash machine won't start
@billiekretschmer64375 жыл бұрын
I have an affinity top load washer and need to replace the springs that are located under the lid and connect to the cabinet somehow. Anyone know how this is done.
@Spartan375X2 жыл бұрын
Mine is weird, the spin cycle doesn't happen during the draining unless I open and close the lid, then it acts normal. It's annoying to run up and down the stairs just to "manually" activate the spin.
@marshablalock55607 жыл бұрын
My name is Marsha Blalock and I watched your video on washer not spinning, and I tried the demonstration but it did not work. The washer only spines out of the washer, but not on the clothes. Need to know how much you charge to check the washer out.
@ImahSillyGirlАй бұрын
Aww, This was so wholesome.
@efzalahmad9027 Жыл бұрын
My Samsung washing machine model WA18F7S8 18kg do not spin with clothes and empty machine complete the spin cycle when i put clothes in it .start spinning but as soon as it tooks speed it stops with a cling
@shimxininahi80242 жыл бұрын
Need solution why pump continues beyond the spin marker. Within 2 weeks the cycle from drainage to spin they worked intermittently where that pump stops just before spin marker and spin completes to end of cycle finishing or pump continues beyond the spin marker but won't automatically spin to the end. My question is what senses the water level had drained and the pump can stop running, then the spin can start? Just before the spin starts I could hear a transition before the spin starts slowly then increases. One note, if I now start the dial just 1-2 clicks before the spin marker then I can see the dial move to and pass the spin marker but the spin does not happen and the pump would continue until the end. Another note, if I monitored or noticed the spin cycle did not come on I was able to manually select any other spin cycle or even the same wash cycle and the spin would start the spin then it goes to the end. But now I can't do that. The pump continues beyond the spin marker. Lid switch has continuity. No spin actuator underneath. Coupling is great! Kenmore Series 70, 110.2683269. Is the problem the main selection switch or some thing else?
@rritter2910 Жыл бұрын
Possibly the timer assembly
@melaniegarcia35414 жыл бұрын
OMG! It worked! I have a GE too tho
@sudieanders74024 жыл бұрын
It donnt wash or start up.
@thadood43734 жыл бұрын
The motor on my washer (Has no belt) runs when its in spin cycle, but doesn't spin. Could this still be the lid switch being faulty?
@charismausa8 жыл бұрын
my machine fills the water and stops, doesn't spin at all. no sound no clicking sound. what's going on? thanks for the education
@marciamccullough62556 жыл бұрын
Michael Mike mine too
@valisapps12546 жыл бұрын
Michael Mike i had the same problem with mine, disconnected the water pump and there was a sock stuck in it, I just removed it and that solved my problem..
@johnnygallardo766 жыл бұрын
my sackable engages but will not spin it is somehow locked i checked lines and there's nothing in them could it be a bad motor?
@adkrick53316 жыл бұрын
My Maytag stop spinning, drains ok. has no belts, looks like a direct drive system. Model A612, serial # 027054 . I can't move the auger/spinner at all.
@empowingminds2 жыл бұрын
Excellent help.
@empowingminds2 жыл бұрын
Excellent video, clear, concise, and easy to follow.
@donfreud2125 жыл бұрын
I have a Whirlpool LSN1000kq0, direct drive. It does everything except spin. Motor runs. The drive coupler is good. It fills and agitates. Door switch is bypassed. Does anyone know what changes, or shifts, to cause the washer to spin? Is this a function of the transmission? Thanks
@donvollnogle63353 жыл бұрын
I have the exact same issue on my Whirlpool. Still havent figured out the cause.
@who8dapple5 жыл бұрын
I have a very old Kenmore #101.82680100. The washer use to wash and spin with the lid completely open. A few days ago, the tub finally stopped spinning. I ran the wash cycle again, and the washer agitates and drains, but does not spin. Is it a faulty door switch, clutch or transmission that I should be focusing on? Thank you In advance!
@vickilarouge48555 жыл бұрын
Jetli _Notme I have the same problem. Did you ever figure it out?
@itsnotthesamething4 жыл бұрын
This isn't my problem. I have a newer model washing machine, that shuts down if the load is unbalanced. You can try and try to drain and spin, but if it is still unbalanced, it will automatically refill with water, and try again. Then it will shut down, if the new refill doesn't work, leaving clothes soaking wet. I've tried removing items, adding items, etc... It is a nightmare!
@marlonesguerra99987 жыл бұрын
hi. sir mam way may tosiba top load waching machine nit spin slow the motor is moving the spin but the eror E2 how to repair
@joseserrano34487 жыл бұрын
My washing machine charges the water but does not make any cycle and in the manual could identify the problem with a count of lights that blink on the control panel but in a previous repair I lost that manual. Please could determine the problem and its solution. The light blinks 4 times is from a general electric washing machine, mod wwse5240g1ww
@gerrydunn57839 ай бұрын
My Amanda washer, fills up washes, drains the water, but don’t change to rinse cycle, for it to spin
@Lightning7474. Жыл бұрын
So basically I should just buy a new washer.
@leelew.14629 ай бұрын
That's what I said 😂😂
@jacobsjacobs41756 ай бұрын
Lmmfao
@naughtysauce4323Ай бұрын
If your a woman maybe. Most real men can do these easy fixes
@daformayorАй бұрын
Basically 😂😂 damn. Step 1: be an electrician or a state registered handyman 😢
@nothankyou5524Ай бұрын
You didn't do that, did you? If you didn't fix it, I'm positive you could have. Either way, no judgements. Not everyone has the time available to tackle a job the first time. Learning curves are a beech. But once you get a couple of repairs of any kind under your belt, things fall into place quicker and quicker. Maybe still not quick yet, but quickER. Never forget that little word "yet". The answer to "Did you get it fixed" is never "No." It's always "No, not YET." If that was good enough for Thomas Edison and Albert Einstien, I figured it would be good enough for me. Hey, best wishes!!
@lemons7938 жыл бұрын
my maytag bravos 300 series washer will not spin at 19 minutes remaining to the cycle any suggestions?
@angelahuddleston8 жыл бұрын
please help me!!! I have a maytag bravos series 300 washer, model #MVWB450WQ0 . the first code it put out was dl so my husband replaced the swithch two times. I see that in your web site it has the causes because the door wont lock so the machine will not wash. It now has the code du. We have done research and it says that it's still the switch. All the lights come on the machine but when it comes on no matter if we unplug the power cord and plug it back in the code is still there and it wont work. Can you PLEASE PLEASE maybe give me a little advice. Tired in TN and too much dirty laundry please help????? thank you so kindly for your info and videos
@repairclinic8 жыл бұрын
+Angela Gray The control board or a bad wire could also cause a dl code.
@niknikalvarez40388 жыл бұрын
Angela Gray
@theobrady24507 жыл бұрын
RepairClinic.com
@theobrady24507 жыл бұрын
RepairClinic.com my fisher & paykel just stopped working after my power went (3) times n 1 wk. what could be the problem? Machine only about 6 months old.
@senthilshunmugam6857 жыл бұрын
thank very much for videos
@yvettegrant33353 жыл бұрын
I just want to learn how to use my new washer help!!!!it's brand new, the guide is not very simple 4 a simple person lol
@ou8agame4433 жыл бұрын
What Brand and Model of Washer do you have?
@noahwahn42647 жыл бұрын
Our Whirlpool Centennial top loader has an intermittent problem where it will drain but not spin. I am assuming it has something to do with the water level sensor. If I unplug it and jostle it about a bit, it usually regains its mind and continues its assigned task. This machine has no fancy schmancy indicator lights like most of the ones I've seen ion the videos. Any thoughts?
@robertvalencia5466 жыл бұрын
Buy a new one
@worstnightmare97723 жыл бұрын
Unplug the washer for 1 minute plug it back in open the lid six times within 30 seconds should reset the motor
@cadavher6 ай бұрын
@@worstnightmare9772 is this a joke lmao
@donaldbedore18818 жыл бұрын
thanks you've been a great help
@ahmadsheikhali61775 жыл бұрын
how has he been a great help
@isabelflores93218 жыл бұрын
MAYTAG model MAV7600AHWQ its not spinning. no noise and the belt seems to be good. help please
@chargriggs1037 Жыл бұрын
How to get an item wrapped in the machine out
@imeemacaraig584 жыл бұрын
Electrolux Hydrosonic wash EWT704S 7kg it wont spin
@suechambers57374 жыл бұрын
I have a samsung top loader wont spin water out
@carolannbyrd48714 жыл бұрын
My ge moffet washer wash n spin sometimes,, won’t spin on rinse cycle
@daledemanchuk79204 жыл бұрын
i had the same problem took the lid magnet off fooled around with the other part of the magnetic switch and now working good again!
@vicgamesvt9682 Жыл бұрын
For me the issue was that the socket my washer is connected to was turned off so I pressed the "reset" button and it started working again.
@richardperkins84576 жыл бұрын
Bingo on first reason. Thanks!
@michaelchambers86455 жыл бұрын
My Whirlpool Washer LSQ8000LQ3 would go through all the cycle, but will not do the final high spin cycle
@vickilarouge48555 жыл бұрын
Michael Chambers I had the same problem. Did you figure it out?
@joycewood5575 жыл бұрын
My washer did wash the clothes but it didn't drain the water, nor will it spin.
@josedominguez78048 жыл бұрын
thanks great video
@marlonesguerra99987 жыл бұрын
Jose Miguel Dominguez hi sir. way may toshiba top load model nambe aw-8960sn spin not working drain stell okey wahs okey but run spin motor run
@marlonesguerra99987 жыл бұрын
bay oredy control clening aredy drum how fixed hlep me sir.
@teaglet Жыл бұрын
Mine just won’t spin, makes a clanking noise Didn’t spin at all
@mygt8a4re4 жыл бұрын
Thank you very helpful!
@michaelwashington3139 Жыл бұрын
Crosly washer starts spinning then it slow down and stops all other functions work
@sassypants60053 жыл бұрын
maytag washing machine won't spin mod MVWX700XW1. what should i look at first?
@kdempsey56587 жыл бұрын
but very...helpful!
@erichoward13042 жыл бұрын
Add worn hub Assembly under the wash plate for why washer won't spin your clothes out. I have had to replace my washers several times. Cheap plastic parts.
@TheCbanksdaily8 ай бұрын
I think mine needs a new belt
@EddieDaOnly18 жыл бұрын
I'm here because my washer just makes like this grinding sound I guess when you put it on spin and close the lid.
@1800will8 жыл бұрын
same as mine, have you found out the cause ? and has it been fixed
@EddieDaOnly18 жыл бұрын
No I haven't. Ended up just selling it for $40.
@matthewmccollum93377 жыл бұрын
sounds like it was just the coupler ...couple bucks.and.like 10min. of.time
@ramirovelazquez91864 жыл бұрын
@@1800will 9m .mxmmm M N. M.j V vvt .e.mmn0 u K Pp . Z opmn
@lindahoete36164 жыл бұрын
My 8kg Top load Teco making a jamming noise on wash & spin cycle .
@BenBlackEquinoxEngelhard3 жыл бұрын
Oh yeah see how easy it is? The panel just comes right off...
@Jeph629 Жыл бұрын
Not a word about a motor reset: go elsewhere.
@satyanarayanagula76437 жыл бұрын
LG only washing machine on off on off running
@lindarichter13674 жыл бұрын
They give no refunds if they tell you the wrong solution. Buy part somewhere else.
@yoda95184 жыл бұрын
Check your water pump for debris
@djdonbentley21416 жыл бұрын
I was trying to wash money in the g.e. but I don't understand why the feds are at my door
@OLOLAK_77776 жыл бұрын
Or buy a new washing machine!
@Iamunique_26 жыл бұрын
fuck off. That shit is not cheap!
@kimd8873 Жыл бұрын
Why didn't u show the other super affordable way to possibly repair the machine for around $10!!!!!!!!!! Pull off the front panel and replace the little white thingy or remove the little white thingy cover wires with duct tape to avoid ever needing repairs again - jerk!!!!! 🤬