Sedikit saran dari saya bang.klo bisa diperkecil lagi lubang pendorong,pasti lebih kencang tembakan air,dan daya dorong tentu lebih besar.🙏
@jblcontrol28crossover76 Жыл бұрын
During your test I noticed the water discharging in a broad cone. I think you'd produce more thrust if the discharge was focused into a tighter stream. Adding a short straight section to the tail end might help with that. Also noticed that cone of water was "swirling" (spinning?). Make your stator assembly more effective so that more of the engine output energy is used pushing the water straight back and less is wasted swirling the water. Instead of a T fitting for the water intake, use a wye shaped fitting so that the water path is more linear and without an abrupt 90 degree bend.
@lcgcano11 ай бұрын
he's going for torque not speed with this setup.
@jblcontrol28crossover7611 ай бұрын
@@lcgcano How does one "maximize torque" from this style of reaction drive? (waiting for an answer based on the laws of physics as they exist in reality)
@kianlengkong9622 Жыл бұрын
Tutorial ini paling dicari dan video edikasi yang sangat bagus banyak selamat untuk anda sukses selalu👍👍👍👍👍👍👍
@bkscreative Жыл бұрын
Terima kasih sobatku 😊😄👍
@LaskarMujahidin-pk7xh7 ай бұрын
Mantap pemirsa puas semoga sukses
@ridwanjufri7432 Жыл бұрын
Kreatip banget bro, tolong vidio uji coba di perahu bro...❔❓❓
@bkscreative Жыл бұрын
Pasti sobat kreatifKu..😊😄👍
@sunartisunarti344111 ай бұрын
Bos berapa harga nya satu set
@harijono57932 ай бұрын
Bagus SKL dan sangat bermanfaat
@nuginina9779 Жыл бұрын
Di ujung corong pembuangan baiknya memakai plat lagi bang,,,jadi air yang keluar tidak berputar alias daya dorong menjadi lemah. Kalau memakai Strip Plat di belakang air akan keluar lurus dengan demikian tenaga dorong akan bertambah. Sekedar masukkan saja bang
@bkscreative Жыл бұрын
Ok, mantap👍 Terima kasih atas masukannya sobat 😊😄👍
@MrSTITAN11 ай бұрын
@@bkscreative no wa ada k ?
@felishaazzahra4947 Жыл бұрын
Mantul bang tak coba terimakasih ilmunya abang kuhh👍👍 Gobjob👍⭐
@stajercs19 Жыл бұрын
Отличная идея для самодельной моторной лодки. На впуск лучше поставить сетку, чтобы не засосало какой-нибудь мусор, или водоросли.
@aridimas Жыл бұрын
ide yg sngt kreatif keren👍👍
@user-ib1ok9ru9o Жыл бұрын
Получился хороший погружной насос для подачи воды на поля. Идея хорошая и полезная
@marcosjuniorgouvea531421 күн бұрын
Parabéns meu amigo, excelente vídeo, wue o abençoe sempre com muita sabedoria e conquistas, 🙌👏👏👏👏
@BENGLASBERKAHCHANNEL Жыл бұрын
Mantap..kreativitas anda aku suka❤❤
@gombanggombang403026 күн бұрын
mantap sukses selalu
@SpencerGaming7580 Жыл бұрын
dude i respect your work and efforts you put into building this this, but it will be uneffective as it could be. The whole design is contrary.
@wolneymateus5833 Жыл бұрын
the first part you soldered is incorrect. the blades should not be inclined. the water should come out in line with the tube
@heyndrajays214610 ай бұрын
Mantap buat mesin mini jet boat memancing
@sudarsono993 Жыл бұрын
Mas sy baru gabung vidio nya .maaaaantep sukses terus buat perahu pancing mas salam dari madura Pamekasan jawa timur
@bkscreative Жыл бұрын
Terima kasih sobatku, Salam Dari kalbar, pontianak 😊😄👍
@kayakfishingbangkalan51 Жыл бұрын
Salam madura
@roblescurbappealconcrete Жыл бұрын
Great work young man. Very impressive. Thank you
@bkscreative Жыл бұрын
At your service sir 😊😄👍
@MukhlisMaulana13 Жыл бұрын
Sukses selalu, Saya Suka Kreatif membangun.💪💪💪👍🏻
@yantoyatiman7990 Жыл бұрын
Mantap lurrrr
@yudianjasmoro742110 ай бұрын
Muwantep nih buat kolam koi
@hamsinsanjaya4332 Жыл бұрын
Mantaap jd terinspirasi
@andrianpaskal4404Ай бұрын
Spil naik perahu dan jalan di air nya bang🙏🙏 penasaran sekali
@ariswanharista5416Ай бұрын
mau Tanya kalau penyedot yg di bawah di kasih saringan kah atau tidak.. bgm kalau tersedot sampah
@iwanmurtanto1798 Жыл бұрын
Pengen buat satu untuk perahu mancing dilaut..😊pake mesin pengerak merk Honda Thailand 7pk..
@alisyibromalisi976 Жыл бұрын
Kalo pake mesin induk semisal panther, lebih joos. Ditunggu kelanjutan video nya. Sukses selalu
@bkscreative Жыл бұрын
Kalau menggunakan mesin panther, diameter pipa PVC nya juga harus besar😄 Kelanjutan nya sedang Di proses sobatku,...😊😄👍
@eliseumartinsdeoliveira96387 ай бұрын
👆👆 ... Eu estava precisando de um projeto caseiro, esse veio a calhar. Parabéns pelo projeto e obrigado por compartilhar ! 👍🙏🙏
@cgd8701 Жыл бұрын
mantap mas.... terus berkarya 👍👍
@bkscreative Жыл бұрын
Terima kasih sobat kreatif 😊😄👍
@vickspearhunter Жыл бұрын
Great Mau tanya om kira kira itu mampu mendorong beban berapa KG ya??
@luisnunes5274 Жыл бұрын
Instead of a T junction use a straight Y improves flow alot.
@hermannwachholz7945 Жыл бұрын
This is exactly what i had in my mind for so long. Want to build something like this for my fishing kayak. Thanks for sharing!
@bkscreative Жыл бұрын
At your service sir 😊😄👍
@harryfp1494 Жыл бұрын
Buy an old inpeller setup or somthing it will work better than this . Even a larger scale rc impeller
@lindarigas8770 Жыл бұрын
Thats right 👍
@lindarigas8770 Жыл бұрын
@@bkscreative 🤔😘
@solimansayed6934 Жыл бұрын
youtube.com/@newmuslimss
@bapaapa7919 Жыл бұрын
Ga masuk sampah seperti plastic atau lain2nya bro?
@duyanhtivi Жыл бұрын
Tuyệt vời vòi dễ hiểu cảm ơn bạn đã chia sẻ
@myasinhasan731111 ай бұрын
Keren mesin boat ya ?
@user-cr5sn5ov1y Жыл бұрын
Спасибо друг хорошая идея
@muarabadakku9 ай бұрын
Kog kepikiran pake pompa keong yg djual Dtoko yaa..kn itu kuat bgt nyemburkn air..mudahn ada yg coba..penasaran
@bkscreative9 ай бұрын
😊😄👍
@mangdeni1726 Жыл бұрын
Keren 👍 bisa jengak jengak
@merantifishing286711 ай бұрын
Mantap bang itu kira"tahan berapa tahun klo untuk di laut klo bahan bukan stainles
@AM-dn4lk Жыл бұрын
Great project. Nice music too.
@bkscreative Жыл бұрын
Thank you sir 😊😄👍
@ferllytokk7968 Жыл бұрын
Apakah air tidak rembes yaa bang melalui pilow beringnya..
@shaneharnish1432 Жыл бұрын
Steel will eat through the plastic over time.... nice job though 👍
@OskharChagazАй бұрын
Mantap bro wwww🥰👍
@acdcfindout Жыл бұрын
Ide yang bagus
@ajatambani2999 Жыл бұрын
Sy suka kreatipmu,muantaaaap
@bkscreative Жыл бұрын
Terima kasih sobatku 😊😄👍
@andrearovelli8213 Жыл бұрын
Complimenti ‼️ Un vero gioiello di ingegneria del "fai da te" dalle molteplici applicazioni ...anche come motore entrobordo per una piccola barca! 👏👏👏👍🇮🇹
@bkscreative Жыл бұрын
Grazie amico mio😊😄👍
@handy-capoutdoors40639 ай бұрын
Ok... now I have another project on my to do list 😅 the hardest part looks like the rear support for the shaft.
@yoshehendra9826 Жыл бұрын
Mantap 👍👍👍👍👍 ini video yg selalu aku tunggu2.....moga sukses sobat kreatif✋✋👍
@bkscreative Жыл бұрын
Terima kasih dulur👍😄
@opowaeoleh8027 Жыл бұрын
Maaf cm saran T nya harusnya d potong serong biar waktu di psang di kapal biar masuk air nya los/lancar
@bkscreative Жыл бұрын
Terima kasih atas masukannya sobatku😊😄👍
@Dwi_tin_garden Жыл бұрын
Waduh... Ikannya bisa pada mabok dong itu om 😁😁😁
@rullyrll8143 Жыл бұрын
Jet propeller DIY sangat ditunggu-tunggu
@ajidarma2942 Жыл бұрын
Part 3 yg perahu pake triplek mesin jet mpdif mama gan..mo lihat eksekusinya diair
@naimanahsap7689 Жыл бұрын
Asalkan pit propeller pas dan selah udara antara jarak tabung kepropller pas ,pasti berfungsi dgn baik
@abrahamsimbiak79978 ай бұрын
MANTAP INI TEMPAT UJI COBA INI DIMANA MAS
@bkscreative8 ай бұрын
Dalam bak air😅
@robbob5318 Жыл бұрын
Great work !
@turongou Жыл бұрын
Mantap, akan tunggu test drive nya nanti. Minat modul nya
@zbigniewteterycz1571 Жыл бұрын
SUPER IDEA . SUPER POMYSŁ . POZDRAWIAM .
@suhidinniat8913 Жыл бұрын
Tanya Mas bro, kalo bikin dengan PVC 6 inch yg didukung oleh tenaga mesin lebih besar lagi perahunya akan lebih laju larinya atau sama dengan yg 4 inchi. Mohon jawaban/komentar nya. Terima kasih.
@ErwinErwin-xw1dk Жыл бұрын
Mantap.....saya minat bang,kira2 berapa buget nya 🙏
@EL_SABIL Жыл бұрын
Mas sy baru gabung nih. Mantap video nya sy menyukainya. Terima kasih, 👍🙏🙏
@user-gv4yf9un5t Жыл бұрын
На выходе должна быть плотная реактивная струя, а здесь мы видим нечто, усиленно перемалывающее и разбрызгивающее воду в разные стороны! Хороший водомёт так не делается, - это результат сложных расчётов и длительных испытаний, поэтому, во всём мире, только две - три фирмы занимаются их разработкой, все остальные только выпускают по лицензии.
@mamatchannel1788 Жыл бұрын
Terbaik bos👍👍
@bkscreative Жыл бұрын
Terima kasih sobat 😊😄👍
@user-ou3ow4eo4v Жыл бұрын
Спасибо тебе, дружище твои идеи очень полезны🇷🇺
@bkscreative Жыл бұрын
к вашим услугам, сэр😊😄👍
@vyranlaise8356 Жыл бұрын
I'm still trying to figure out what to uses that for. I see you didn't get every angle perfect to keep the balance from shaking it a part. Also you should of used lock washer. Also practice welding. Get the melted bead to flow using the power to get it hot enough to flow the bead using a walbow like walking . Put a longer shaft on it so you. Don't have to worry about the motor falling in or getting wet. Put a net on the bottom so the pump don't suck any sticks into the system. The right balance is very important. So not to vibrate the part lose or cut its way through the PVC pipes to last. Hope this helps you out.
@bkscreative Жыл бұрын
Thank you for the tips😊😄👍
@carlosalbertosilva3176 Жыл бұрын
incrível, genial meus parabéns
@anakrantau3148 Жыл бұрын
Mantap bang👍👍👍
@bkscreative Жыл бұрын
Terima kasih sobatku 😊
@alibabaabadila72173 ай бұрын
Muy bueno ....tengo una duda que diferencia tiene con una elice????? Necesita menos revolución? Tiene mejor empuje.?? Si me puede responder se agradece
@user-ip1eh6nr7b7 ай бұрын
Di produksi bos... Pasti banyak yg pesan....
@cartertrefz4585 Жыл бұрын
Pretty clever but somebody should seriously teach you how to weld
@Chloe_Gaming-fe9rv Жыл бұрын
Keren bro
@dyslectische11 ай бұрын
Humm looks great . Sombody know rpm for a electric engine to use ??
@pemancingkampoeng3625 Жыл бұрын
iya kalo posisi air mati..tapi kalo udh ada arus..biasanya lsg loyo,soal nya posisi lubang hisap salah posisi,metode nya hrs sm persis kyk jet ski,baru bisa efektif,lubang hisap hrs berlawanan arah dgn lubang keluar
@rian1621 Жыл бұрын
kan ada L pipa tinggal dipasang ke arah air masuk dah siap
@pemancingkampoeng3625 Жыл бұрын
@@rian1621 sangat bahaya,bisa mengakibatkan barang2 sampah dll masuk,bisa patah kipas,metode nya mesti sm kyk jet ski
@perangkaptikus2612 Жыл бұрын
Supeeeer.....👍👍👍👍
@eshamwanmohdakhbar1885 Жыл бұрын
Boleh uji di perahu jugak berapa kelajuan yang dapat bro..
@gmcs91 Жыл бұрын
Waow seperti basoka
@iniakusi17 Жыл бұрын
Brapa harganya klo jdi bang... Jual di online aja🤣
@user-ht1rv1ls6r2 ай бұрын
Di jual gak water boatnya om???
@maharuddinuddin3524 Жыл бұрын
Kalau pake mesin mobil pipa berapa inci besarnya yg dipake
@ryanjohnson1814 Жыл бұрын
Not enough rpm, versus thrust ratio, u really need to be able to get 4,000, 5,000. Rpm. I imagine that no successful real test with a board or Kayak has happened? Be very slow, I'd assume. Thrust to weight ratio
@LHoover Жыл бұрын
Sekarang tambahkan 600cm pipa lurus ke pembuangan Anda, ini akan membantu meningkatkan efisiensi. Sebagian besar penggerak jet air kehilangan daya total 40% tanpa sambungan air mekanis penuh normal Now add 600cm of straight pipe to your discharge it will help to increase efficiency. Most water jet drives lose 40% total power without normal full mechanical water connection
@SilviInsania-si1rm6 ай бұрын
6meters of pipe???
@LHoover6 ай бұрын
@@SilviInsania-si1rm heck yeauh! The more smooth straight pipe run you have after all your "work" to allow your water 'cylinder' to smooth out uncavitate and solidify as a water column preferably with a firm full corkscrew rotation pitched to the brush roller on your vacuum cleaner. To appropriate a line from Ben Stiller, 'DOIT'🤠 Better penny up for the SCHD80. precise engineering optional.
@belarminoskills6007 Жыл бұрын
nice idea...
@carloscameschi Жыл бұрын
Incrível, parabéns amigo.
@bkscreative Жыл бұрын
obrigado meu amigo😊😄👍
@bp.piscesboy16467 ай бұрын
itu mesin pwmotong rputlah bos 🙏🙏🙏🙏🙏
@kidsfuntoys641 Жыл бұрын
Good job,,,,👍
@bkscreative Жыл бұрын
Thank you sir 😊😄👍
@jan.lmateboer7884 Жыл бұрын
Lot's of norse. Could an electric version a solution?
@hobimancing6886 Жыл бұрын
Mantap 👍👍👍👍, kapan tes ke perahunya brooo
@bkscreative Жыл бұрын
Segera sobat kreatif 😊
@cameraman1234567890 Жыл бұрын
Quite impressive, sounds like you need less pitch, you cant reach close to max RPM
@MarceloSilva-ex9vx Жыл бұрын
Saudações... Pude perceber que deveria de ter um anel com parafusos no eixo para limitar o deslocamento do eixo da extremidade ou da bucha próximo a hélice.. tudo bem que o motor não permitirá o deslocamento, mas por segurança será ideal.
@Nicoricanmarxist Жыл бұрын
Hey i love the impeller. If you used something to hold the angle while welding the impeller, so that each fan blade had the exact same angle, I think you could improve efficiency. Dude, I gotta know what’s up with the country music?
@suhidinniat8913 Жыл бұрын
Untuk membuat lingkaran bushing dan baling-baling menggunakan plat setebal berapa mm ?
@adarshkv1744 Жыл бұрын
Which engine you have used on this,is that a grass cutter?
@bkscreative Жыл бұрын
Yes it is 😊😄👍
@junaydynaydy Жыл бұрын
Mantap bos
@bkscreative Жыл бұрын
Terima kasih sobatku 😊😄👍
@noxy.mlbb05Ай бұрын
misal buat mesin ketinting 12 pk , cocok pipa berpa inchi bang
@bernaduskailemakurfishing Жыл бұрын
Jenius sekali senior
@bkscreative Жыл бұрын
Terima kasih sobatku 😊😄👍
@bernaduskailemakurfishing Жыл бұрын
@@bkscreative gas pull bro
@bernaduskailemakurfishing Жыл бұрын
@@bkscreative sama-sama sobatku gas poll
@kbhhandicrafts66936 ай бұрын
Good idea
@MuzzaBikeFix Жыл бұрын
Very cool bro seriously
@bkscreative Жыл бұрын
Thank you bro, I'm appreciate it 😊😄👍
@daengracing11 ай бұрын
Ko mirip moto gp ya suaranya
@DavesCoolCustomBikes Жыл бұрын
I’d love to see it in action and know the speed it produced
@joseevaristodealmeidadealm309711 ай бұрын
Eu qj
@joseevaristodealmeidadealm309711 ай бұрын
Eu quero comprar as conexões Pará fazer aonde consigo as pecas