Toyota Camry 2013, 2014, 2015 Air Mix motor // Blend door motor AC or Heat Control Actuator

Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#2013camrybelnddoor #blendoormotor #camry #toyotacamry #bleddoormotor #heatdontwork #acdontwork #airblendmotor #acnotcold 3acfix #2014camryblenddoormotor #2005camryblenddoormotor #2012camryblenddoormotor

[@AB1DE]

Thank you for this! When you search ‘2014 Toyota Avalon Blower Motor’, I got all the Camry, Corolla and 4Runner videos. Glad I found this! Appreciate ya!

[@RBTheMechanic]

Cool yes they are very much similar prolly diffrent part nunber

[@jameswhite1319]

As always thanks for your time sharing ☮️from Houston Texas

[@RBTheMechanic]

Welcome

[@BluRibbonReviews]

Thank you for the straightforward video. I still see that you respond often. My 2016 Toyota Camry SE from North America started blowing warm air out of the driver's side but ice cold out of the passenger side vents. I have single-zone climate control and no rear vents. When I'm driving for a while and the AC gets to its coldest on the passenger side, I notice that the driver's side is only 10-20 degrees Fahrenheit warmer than the passenger side vents that are blowing ice cold. Does this point to low freon? I don't believe the AC has ever been serviced. On a separate note that may not be related, my circulation servo starts clicking loudly and rapidly. Checking the OBD2 shows that when it's trying to close, it will get stuck on the second to last pulse and keep trying to close, causing a clicking noise until I disengage the recirculation button. Strangely enough, it doesn't happen every time. Sometimes when it's hot out, it will work just like normal and not click. Other times, it will start clicking immediately. It also clicked very loudly when the car was off a few times after the car was switching to the fresh air vent while parked. Regardless of the circulation motor being loud and clicking 75% of the time and having to turn it off and use fresh air only, the driver's side is always warmer 100% of the time now. From what I can tell, the blend door motor is working fine, as I can switch from cold to hot, and it changes in both vents. But when switching back to cool, only the passenger side vents get cold immediately. Sorry for the long message; I just read all the other responses, so I tried to provide as much information as possible for my single-zone AC issues.

[@RBTheMechanic]

Well that could be possability low refrigeration even check pressure could be faulty read due to hot at pressure so 1st step recharge the system and hopefully it’s good

[@BluRibbonReviews]

@@RBTheMechanic yep that'll be getting done on Tuesday

[@BluRibbonReviews]

@RBTheMechanic I did recharge my AC, and that fixed the cooling issue for both the driver and passenger sides. My question is, is the clicking coming from the recirculation motor? What would that part be called if I wanted to replace it myself? I have single climate controls and it only happens when I press the recirculation motor. When recirculation is off and it's only pulling in fresh air, the motor doesn't click. I see that there are multiple different doors, but I can't find one that's just called the recirculation motor. I noticed that when I see the recirculation flap open and close, the clicking only happens when the flap is pushed to the closed side to recirculate air. When it opens to fresh air, there are no issues or clicking. So I've seen it called a few different things like a blend door actuator, but for my 2016 Toyota Camry single-zone climate, I'm looking to replace or at least disconnect the circulation motor to leave it closed in the meantime so it doesn't have power and continue to click when I need recirculation mode.

[@ezenglishwith]

Good video bro, I have Toyota Camry 2014 and air is not blowing to windshield or legs, only blows to face through front vents, took it to mechanic and all of them said blend door actuator. Can you actually make a video on how to replace it, I have the part, i tried to take the old out out but I couldn’t

[@RBTheMechanic]

I can’t just make a video I would need a vehicle for repair but the motor that changes air direction is called mode door motor it changes the air mode direction the blend door motor blends hot and cold to make the temperature you want and some times tapping on the motor works

[@foot2theballs]

Awesom video-no fluff, and very informative! I'm diagnosing a B1273 engine code on my 2015 Camry right now, and I need to check my servo motor. Did you say that if the motor is NOT working, the center white piece WILL move when you put your finger on it?

[@RBTheMechanic]

To feel that it’s turning if u can hear it or see the arms moving

[@foot2theballs]

@@RBTheMechanic interesting-I would have thought if that piece and the arms were moving, that would mean it was working right. Thanks for saving me some headache haha, I appreciate the reply!

[@atifalyafai4860]

Thank you very much. I was half same problem and I fix it.

[@RBTheMechanic]

Welcome

[@RBTheMechanic]

You're welcome!

[@fisherbrown903]

Thx mr. Rb same model

[@RBTheMechanic]

U welcome

[@copaseticguerra9646]

Thank you so much.

[@RBTheMechanic]

You're welcome!

[@bluesdirt6555]

Great video ! Is that the same part on 2011 Camry xle ?

[@RBTheMechanic]

No I don’t think so might be diffrent design

[@elflakko9422]

Hello sir could you please help me? I have a 2016 Toyota Camry SE that won’t blow cold air just warm but the pressures are fine and it has no leaks but I still had it evacuated and recharged, sadly still no cold air just warm air so I checked the blend door actuator and saw it move but only a quarter turn when I moved the setting from full hot to full cold. I’m not sure what it can be since when I turn it to full hot, it does get very hot but when I turn it to full cold is when it just gets warm. Is it supposed to be turning that little or is it maybe jammed up? Thank you 🙏

[@RBTheMechanic]

Well I’m not sure what ur seeing with door it suppose to open up check power to ur compressor

[@hungvungoc7253]

my driver side didnt have heat . only cold . and i saw my blend door actuator still run ? what else should i check ?

[@RBTheMechanic]

U have single or dual temp control? If u got dual u need to check both also check heat control valve

[@KevinC-fb8lp]

Hey RB are there two blend door actuators?, I’m getting warm air on the driver side vents and cold air on the passenger side. Your video shows the passenger side but I’m wondering if there’s a driver side one and if so where would that one be located?

[@RBTheMechanic]

If u got dual control then each side has one also some times low Freon could be the cause only half of the systym will get cooled

[@KevinC-fb8lp]

I don’t have duel control climate, so maybe it’s just that one by the blower motor only

[@1capuchino]

I have same problem..wonder was the problem?

[@RBTheMechanic]

@@1capuchino bled door see if it moves as u turn temp up and down

[@JosueGonzalez-ti4mo]

​@@KevinC-fb8lpdid you ever find the solution?

[@fisherbrown903]

Is it the pcv valve. I need to add 800 m oil every 1000 miles , I change oil. Every 5000 miles I c pcv hose got lot of oil. And under intake manifold. , I use the uv dye too

[@RBTheMechanic]

Replace the cake and keep an eye on it

[@febinshibu3821]

My 2014 Toyota Camry LE started blowing warm air out of the driver's side but ice-cold air out of the passenger side vents. It has single-zone climate control and no rear vents. I recently purchased the car. Does this indicate low refrigerant or a bad blend door actuator? There is no noise.

[@RBTheMechanic]

First think it maybe low on refrigeration

[@febinshibu3821]

Thank sir ​@@RBTheMechanic

[@Sweetmicky23]

My camry xle 2016 makes a ticking noise coming from that area while I’m driving and accelerating and it would usually stop when I start braking. Sound doesn’t happened all the time while driving but it’s getting annoying, have any idea on what it could be??

[@RBTheMechanic]

Not sure maybe bled door acuator

[@Sweetmicky23]

@@RBTheMechanic I have a video

[@tiphneydiaries4848]

Ok so they do spin even if they may not be working? So maybe I do need to change it. 🤔I'm confused i thought because i heard sound and saw movement that i should not change it but it's the lady thing i 😮know to try. Unless i have a leak.

[@RBTheMechanic]

They should turn like lot if u turn the setting lot

[@tiphneydiaries4848]

@@RBTheMechanic ok it is turning when I change the temp. I just tested and no freon in there. Now I know why line not cold. I have the new blend door should I change it? Or is it just a waste of time to change it since it is moving when I change from hot to cold? Or just try to add freon and my coolant is low also.

[@RBTheMechanic]

@@tiphneydiaries4848 do ac service with ax machine vaccum for 20 minutes and recharge. And coolant got nothing to do with ac

[@tiphneydiaries4848]

Tried all of these. I got the clutch to move but compressor was not kicking on. I still nothing cool. Was told by 2 mechanics I needed compressor. Put compressor on and still no cool air. Said drier was clogged.

[@Darth_Raider_]

Great to the point video. Does anyone know the location of the actuator for the driver side on a 2012 Camry?

[@RBTheMechanic]

Should be down bottom opposite side that’s if u got dual control

[@Darth_Raider_]

@@RBTheMechanic it not duel climate. I just figured it had one on driver side cuz my driver side blowing hot and my passenger is blowing cold 🫤

[@DhatboiiJay239]

I am literally having the same issue on mine! I hope you get an answer because I am curious as well@@Darth_Raider_

[@RD_Channel24]

@@Darth_Raider_ I also have a 2012 Camry and I am having the same exact problem with my AC where its blowing hot to my driver side and the passenger blowing cold.

[@Darth_Raider_]

@@RD_Channel24 I wish I could help u, but my Camry still blowing hot on driver and cold on passenger n I can't figure it out 😭

[@nickbrian2595]

How many blend door actuator has 2016 Toyota Camry le? I found it for passenger side but I couldn’t find for driver side.I checked back of pedals but I couldn’t see that.

[@RBTheMechanic]

Maybe it has single motor do u have dual temp control on dash

[@RBTheMechanic]

Not about how many if u are able to control both side temp then it got 2

[@nicenow25]

​@@RBTheMechanic oh right

[@erniebartolome5848]

Aloha from Hawaii.. I have a 2017 Toyota Camry. Why does my AC blows cold on the passenger side and warm on driver side? How can I determine if my blend door is at fault?

[@RBTheMechanic]

Check to see if the bled door turns by turning the temp up and down also if u put it on full hot it will give u hot and when u turn the temp down it will get cooler that will indicate it’s turning so do check it visually other wise it could be low refrigerant

[@erniebartolome5848]

@@RBTheMechanic so if it’s not turning, then I need to replace the blend door motor?

[@RBTheMechanic]

@@erniebartolome5848 before u replace it remove it and use it turn it slowely by hand the door u can check that way don’t force anything

[@erniebartolome5848]

@@RBTheMechanic thanks bro🤙🏽

[@RBTheMechanic]

@@erniebartolome5848 welcome

[@mgomez5606]

RB, do they sell kits to fix them?

[@RBTheMechanic]

What u mean by kits this is purchased as a part assembly

[@geletmote]

My camry hybrid 2010 is getting a delay to my AC controls when I power up the car, never had this issue, will this fix the problem? What do I have to do?

[@RBTheMechanic]

Prolly not this either will have heat or ac set to one temp

[@user-eb5mb7og8z]

Did you find out what it was?

[@geletmote]

@@user-eb5mb7og8z its fixed itself up, have had some bad mechanics at toyota recently all they are after is the $$

[@jasonlaw1048]

I have one problem on my car... When i set the ac temperature to low i can feel the air flow become stronger... When i set to 25 degrees above i can feel the air flow become weaker...is that normal for dual climate system?

[@RBTheMechanic]

It might be normal to keep less cooling

[@jasonlaw1048]

@@RBTheMechanic tqvm for the answer.... Really appreaciate it... 👍👍

[@leeshelenberger7240]

@RB, where is the driver side Blend door Actuator for 2012 Toyota highlander located?

[@RBTheMechanic]

If u got dual control for temp there’s one on each side if u got single temp control then there’s only one

[@leeshelenberger7240]

I'm not sure if i have dual control temp

[@RBTheMechanic]

@@leeshelenberger7240 can u adjust temp on both side ?

[@leeshelenberger7240]

@@RBTheMechanic no

[@leeshelenberger7240]

@@RBTheMechanic only one knob

[@hussnainali_official3700]

I have a camry 2012 XLE and i have 2 issues. One when i turn on the car HVAC takes 20 seconds to bootup. Two when i change the direction of vent it does not change, the air just keeps coming from all vents. Could this be due to HVAC Actuator?

[@RBTheMechanic]

U need to check if ur mode door motor is operating first

[@hussnainali_official3700]

@@RBTheMechanic how can i check that?

[@hussnainali_official3700]

​@@RBTheMechanicI just replaced driver side actuator no change. Can you tell where the door motor actuator is?

[@RBTheMechanic]

@@hussnainali_official3700 might be by drivers foot well

[@jamesmast5243]

Hey I bought and installed a new one but the new one starts turning then just starts clicking. Did I not align something correctly? Help I’m dying over here!

[@RBTheMechanic]

I would take it out and connect the connector while it’s out it will find its spot and then insert it I don’t think u did anything wrong

[@jamesmast5243]

@@RBTheMechanic thanks! I did that but it’s still clicking. Ordered another better one. We’ll see if that does it.

[@RBTheMechanic]

@@jamesmast5243 u still got the original old one?

[@jamesmast5243]

@@RBTheMechanic yes I do.