Toyota Tundra A/C issues repair update

[@madmike4]

My 2007 tundra had been stuck in the defrost mode for 5 years now and I just live with it as long as I have Ac and heat . I’m not tearing that dashboard apart . No way Jose’😂

[@4runnerandtundramods359]

Today is 6/7/22 The book hours for this job is 7hrs. My trusted mechanic only charged me 6hrs labor for a total of $835dollars parts and labor. Parts were $180 for the actuator. Im pretty handy I just didn’t feel like tacking this project. Some times you just gotta pay! Im in Northern Va

[@domeniconelli8382]

at the 6 minute mark you said, "We can control the air flow direction now, which is lovely." HAHAHA Lovely...I can't wait to get that control back. I'm installing my new servo tmr. Gonna need to get some heat up on the windshield before winter kicks in.

[@jamiesloan5902]

I found both the driver side, and passenger side assemblies. My truck is blowing cool air ONLY. All of my vents are working properly. I can watch the gears move, as I change air locations. It's just not getting hot, the way it should. This is really frustrating. Any ideas, or suggestions would be greatly appreciated. It's like the main flapper isn't directing the air from the heater core. It's just luke warm air.

[@roadtoadtwo]

Mine "08 Tundra is similar, there is no heat on the driver side floor or vent, just cold air but the passenger side seems fine. Did you find a fix for it?

[@deezerdeezer]

@@roadtoadtwo Did you get it fixed?

[@deezerdeezer]

@@roadtoadtwo For me, replacing the servo motors (the entire plate) fixed it. Followed these instructions: www.tundrasolutions.com/threads/climate-control-system-delay-after-startup.192498/

[@briannaolinger2281]

so my question, was it just syncing needed or did you replace something. I have the delay and vents not working, but after I turn the truck off about 45 seconds later I can hear the components moving back and forth. in the 3 videos I see what you did, but don't know what fixed the problem. I have a 2007 tundra, and have everything removed but the servco, and just want to know what the fix is. Thanks for listening...

[@extremeoffsetrims]

You got the longest Video with the best explication, but Jesus you talk slow :) . Thanks foe the Video :)

[@jgreen6781]

Any advice on on reattaching a broken lever from one of the shafts inside the air box? I was thinking of using a screw. Your opinion would greatly be appreciated. Thank you.

[@gerardotorres9960]

Hola tengo una Toyota tundra 2007 y no está enfriando el lado del pasajero y él del conductor si,si fuera tan amable de decime cuál es la faya sé lo agradecería

[@rickfillion5666]

where is this part???? NO info on how to access, remove and replace even if replacing with a new one. Thank you for the info for those who want to struggle with syncing and putting all back together in hopes of no more issues. I'm happy to buy the new synced part for a couple hundred. If I knew where to take out the old, and put in the new. Why has TOYOTA made this a huge secret and so difficult. I'm not trying to repair the door actuator. As in driver door. That's some of the info that comes up. Nothing with my problem. help ???

[@brittg21039]

Please help!! I'm having the same problem with my 2007 tundra. When I turn the ignition to on there is a delay as well. The temperature initially defaults to 75 degrees and the air blow to the floor vents. I'm able to control the different modes. The system does not remember the settings. I want to try and the repair myself but I'm not sure how to sync the vent doors once the servo gears are set. I have alldata for the truck but can't find the necessary info in regards to removal and installation of diver side servo. Any help would be greatly appreciated!

[@blackmoses5235]

Brittany Gamble did you ever get the problem fix?

[@JamesPullman]

Brittany Gamble did you ever figure this out. I have an 08 Tundra with the same issue

[@rodrigosandoval9571]

@@blackmoses5235 can you help me I have a 2008 tundra first the ac button started blinking and it was blowing air but not cool or hot then it just quit working now it doesn’t even turn I check all the fuses and they are all good what could be the problem any help I would appreciate thanks

[@kirkmorin1974]

your the only person on KZbin with info on this problem thanks for the info . Can you tell me where i can find a schamtic for the levers and gears on this truck i have a 2011 tundra simalar problem ?

[@blackmoses5235]

kirk morin Your welcome bro...try alldatadiy.com thats where I got the schematic for mind.

[@craigborden764]

Any tricks on getting those vent arms lined up so they mesh properly when installing the ac servo plate? I have the AllData schematic, which is the same as the Toyota Factory Service Manual that I have. The problem is those arms don't want to stay put and you can't get hands on them when the plate is in place. Thats where I'm stuck at the moment since I can't seem to get the vent arms properly engaged with the gears on the servo plate.....

[@randolphcirilo4800]

Craig Borden .. Craig did you ever figure it out? I read somewhere that if you want to keep those arms in the spot where its aligned, to turn the air flow knob all the way to the left or dash vent position.

[@nxtgen2b416]

Had this same issue with my 08

[@jamiesloan5902]

I'm getting ready to tackle this same problem in my 2008 tundra. Where are those things located? Is the passenger side one behind the glove box? Is the driver side one next to, or beside the gas pedal? I wish you would have shown the location of these modules. I guess I'll just start tearing things apart, until I find them.

[@patrickniedermeyer2112]

Agreed. I assume this is behind the glovebox, but he never mentions it or zooms out and I dont recognize what's in the frame.

[@deezerdeezer]

Check out this post www.tundrasolutions.com/threads/climate-control-system-delay-after-startup.192498/ Yes, the drivers side is right of the gas pedal and the passenger side left of the glovebox.

[@brandongregory4849]

both motors are moving. the little gear above the servo acts like the floor doesn't exist. it pauses at vent , then when switched to defrost it sticks for a sec on floor then jumps right to defrost

[@blackmoses5235]

Brandon Gregory Sounds like you may have a gear stripped or rod broken. Remove your ventilation tubing for the floor on the driver side and watch the operation of the vent door

[@galileamoreno9102]

+Black Moses allí más

[@randysilvagni4103]

I am doing this now! Can you share the sheet to synchronize the air box levers and the assembly gears?? Thanks

[@deezerdeezer]

Check out this post, has the info attached: www.tundrasolutions.com/threads/climate-control-system-delay-after-startup.192498/

[@brandongregory4849]

what would cause me to not have floor heat but everything else works??? 2012 tundra dc

[@blackmoses5235]

Brandon Gregory In this video you will see the servo with the B on it, thats your problem. Check to see if that servo is operating

[@BrandonBrooke453]

I’m trying to install this but I freaking can’t. I need help man!!!! How did you install it? I need instructions

[@frosty1211]

Brandon Brooke did u ever figure out how to get it back in? I’m having the same problem.

[@BrandonBrooke453]

Bryson Bowman nope. It’s way too hard. I’m gonna have a shop do it

[@ED-vk3sg]

Reassembly is a challenge. I have gone to all data and paid $30 and can't find anything on the synchronization. I need assistance on where the doors should be positioned to reassemble. Can you help?

[@blackmoses5235]

E D alldata has the info

[@randysilvagni4103]

Did you ever find the info on alldata??

[@dgymboh]

Alldata doesn't show one of the mix door levers (controlling the rear floor vents maybe?) that engages the race in the largest of the gears on the damper servo assembly. Any advice on where to set that one? They sure didn't make this easy.

[@deezerdeezer]

Check out this post for more info: www.tundrasolutions.com/threads/climate-control-system-delay-after-startup.192498/

[@daedma3]

hi man i need your help please .in the minute 1:40 you said that you took off the bottom servo motor .can you take off that servo motor without taking off the whole thing? that servo motor is not working in my tundra.

[@blackmoses5235]

It's best to get the complete servo assembly and replace with new because the assembly has to come off anyway

[@daedma3]

Black Moses ok thank you but if i want to take off just that servo motor.is it possible?

[@blackmoses5235]

Yes that's possible but you still have to remove the servo assembly

[@deezerdeezer]

You can't remove the motors without taking off the entire servo assembly first, because the clips are on the side facing the heater box.

[@daedma3]

@@deezerdeezer you right i had to do remove the assembly but i did fit and now my truck works perfect .every one with patients can do it .

[@luissolis5652]

this was a nightmare