Tundra AC Flap Actuator Motors Fixed

  Рет қаралды 28,373

WARREN

WARREN

Күн бұрын

Пікірлер: 37
@RaulDuke-b1j
@RaulDuke-b1j 2 ай бұрын
This guy over here, doesn't just replace it with a new but tears it apart and replaces the broken component. Who does this these days? Freakin' awesome
@RazbagLLC
@RazbagLLC 4 жыл бұрын
You Sir are a genius. Thank you. Also, I loved hearing your kids in the background. You’re a good dad to be so patient 😁
@tomadkins2799
@tomadkins2799 3 жыл бұрын
John Caleb Warren You are the man !!! You just saved me thousands !!!!! I watched this at least 10 times, ordered the servo part and was nervous as im not a mechanic but I dove into today and just like you said, an afternoons worth of work, took about 4 hours but I could not have done this without your well made clear instructions, I really appreciate you posting this video, It worked !! my 2008 Tundra now has climate control options restored, !!! Many Thanks !!!!
@AroniousP
@AroniousP 4 жыл бұрын
I used this video to tear apart my truck today and a guy on Tundra forums to align the new servo assembly correctly (temp control motor went out). Very helpful video and key to making this a relatively painless 6 hour job. Found a new servo assembly from Toyota for $120. Thanks very much for posting!
@joelferguson6423
@joelferguson6423 4 жыл бұрын
Excellent video. You have helped many Tundra owners for years to come!
@QuickenMac
@QuickenMac 3 ай бұрын
Thanks for this video. I had put this job off for 2 years as I suspected how difficult it would be-and it is. (And I do industrial maintenance as a day job.) This is an all day job as it likely will take it several tries getting it all to line up and working. I personally didn't have any luck trying to line up the inner blend door by sticking something through the alignment hole. What eventually worked for me is lining it up, and using a long piece of electrical tape in about a 7 o'clock direction away from gear to hold in place, When servo assy slides in flush and isn't rocking. I put screwdriver in hole as I tightened down. Then, I pulled on tail of tape sticking out from under assy to remove.
@harrykong
@harrykong 2 жыл бұрын
Wow I’ve had this problem for years and just stumbled on this video. Thank you so much for making this 🙏
@Navin.R.Johnson
@Navin.R.Johnson Жыл бұрын
Excellent instructions! Saved me a TON of time. Thanks for posting!
@michaelc1063
@michaelc1063 4 жыл бұрын
Word of the Day: FENAYGUL
@johnny102015
@johnny102015 4 жыл бұрын
Thanks for the video big time. Content and commentary was 👌😂. Gonna go try it out to see if I can get the same results. Thanks again
@richard1973
@richard1973 2 жыл бұрын
Thank you so much!!! I was able to fix mine.
@mellowkoopa
@mellowkoopa 20 күн бұрын
This is great. I'm curious... My actuator motor died. Do I NEED to take off the whole assembly or can I just pop off the motor and put a new motor on?
@drewmanning1025
@drewmanning1025 Ай бұрын
You have one on how to do the hot to cold flap? My gear is broken. NO HEAT
@trevorcapon8700
@trevorcapon8700 3 жыл бұрын
Hey John, I have smoke billowing out of my vents when i shut the truck off. It is smoking because of the constant feed of air from the blower... and the mouse nest that i BELIEVE is down there. No other problems. When the heater element up against the floor boards / firewall warms up, something is smoking. I have previously gone about as far as you have without removing the flap motor assemblies. My question is: Your video is not intended to show further access to the venting assembly, however, do you know if i can gain MORE acsess by removing the flap motor assemblies? Currently I am fishing a grabber tool like in your video and a fuel-line attached to a shop vac down the vent DIRECTLY after the blower motor. I can see in there with a light and a mirror and I have removed some leaves and pine needles already but the smoking continues. I need to get further. I really do not want to take any more apart than needed but do you have any ideas to help. There is something further down that is heating up. Ideas on how to get further????Thanks
@csotelo225
@csotelo225 2 жыл бұрын
My Tundra has the following problem. When you turn the AC switch on nothing happens for about a minute not even the recirculate light comes on. Then after about a minute everything turns on and works fine the air blows correctly from each vent when I change the knob setting. I noticed in the video you said that there was also a recirculation actuator that is behind the glove Box.. From what I described above how would I know if it were the actuator that's behind the Center console or if it's the recirculation actuator behind the glove Box? Another thing I noticed is when I turn the car off and the air has been on or if I change the knobs from cold to hot I can hear a growling noise... it sounds like the actuator motor... That also happens when I turn the vehicle off within a few seconds then it stops. I hear that growling noise every time I use the air and I turned the vehicle off or I just start and I tried to turn the air on. Also one note. The recirculation light likes to turn itself off frequently by itself I'm constantly having to push it and turn it back on... any information would be greatly appreciated as I would like to attempt the repair myself however I don't know which actuator to replace, the one behind the dash or the one behind the glove box.. thx
@noahcao4026
@noahcao4026 2 жыл бұрын
I got it.Thank you very much!
@ryanharte528
@ryanharte528 3 жыл бұрын
My truck won't stop blowing a/c in the floor. Do you think this could be my problem? Forums say Toyota's just do that. Thanks for taking the time.
@turbo8677
@turbo8677 Жыл бұрын
The the driver side heat flap the same as the passenger side?
@keithmoon3361
@keithmoon3361 2 жыл бұрын
Excellent video. What an absolute disaster of a design by toyota. There is so much room under the dash, that this should not be more than an 30-60 minute plug and play job.
@steveg3710
@steveg3710 4 жыл бұрын
John, Great video. I have the exact problem. Could you describe in detail how you swapped out the white gear from the bad control motor to the new one and how you aligned the gears so that they meshed correctly? Dealer told me it would cost about $1000 to fix this problem, but after watching your video, I'm going to be able to fix it myself for considerably less. Thanks in advance for your help!! Steve
@benrivera4379
@benrivera4379 4 жыл бұрын
Excellent video. I see now what needs to be done to repair my a/c. I've been able to locate the actutator motor but not the black gear. Were did you find the black gear?
@JohnCalebWarren
@JohnCalebWarren 4 жыл бұрын
Both gears i was dealing with were white
@prussnblk6457
@prussnblk6457 4 жыл бұрын
What’s the name of that silver? Want to paint my Supra quicksilver or that
@jgreen6781
@jgreen6781 4 жыл бұрын
What does the lower servo motor control?
@JerryReeves-dh9hp
@JerryReeves-dh9hp 6 ай бұрын
Nice 👍
@ChristopherSmith-rn4wd
@ChristopherSmith-rn4wd 4 жыл бұрын
Thanks for the video ,I just started having the very same problem ,can you tell me where did you order that gear ? I am not able to find it online.thanks
@JohnCalebWarren
@JohnCalebWarren 4 жыл бұрын
I actually just got another used one off ebay. Had to buy the whole flap motor w/ the gear attached. I think it was like 20 or 30 bucks. Then I swapped the gear over to my motor
@dougshoemaker6300
@dougshoemaker6300 4 жыл бұрын
What was the part number? For a reference.
@mohammadlatif5414
@mohammadlatif5414 4 жыл бұрын
Hi bud I have Toyota tundra 2008 I have the same problems can you please tell me how long it takes you to do the job? And how much cost ? Thanks
@JohnCalebWarren
@JohnCalebWarren 4 жыл бұрын
It takes about 3 hours to pull the intake manifold, replace the valve assembly & reinstall everything. It cost around $250- 300 for the part
@justinfreeman1839
@justinfreeman1839 9 ай бұрын
It’s still jumping gears in the last video!
@rsanchez5676
@rsanchez5676 Жыл бұрын
Quick easy?
@lang5264
@lang5264 4 жыл бұрын
What's the name of the part exactly? I tried typing the part number in but got no results
@JohnCalebWarren
@JohnCalebWarren 4 жыл бұрын
It would either be flap motor or blend motor
@lang5264
@lang5264 4 жыл бұрын
@@JohnCalebWarren is that the parts name of the gear that failed? Mine takes time to come n on and will only blow through defrost
@lang5264
@lang5264 4 жыл бұрын
@@JohnCalebWarren i found another control unit to fit my truck on ebay it supposedly will be here on the 4th. But I'm worried I will have to try to do what you showed in the video.
@JohnCalebWarren
@JohnCalebWarren 4 жыл бұрын
Let me know if that fixes your problem after the 4th oh, because I'm still considering changing ours out
Tundra heater climate control defrost vent Finally Fixed
12:07
2005 Tundra   Vent Contols, Re assembly
13:51
JRK Services
Рет қаралды 21 М.
2008 Toyota Sienna Blend Door Actuator Replacement
40:41
Nature's Arsenal
Рет қаралды 100 М.
Tundra AC & Heater Problems Fixed
14:39
WARREN
Рет қаралды 19 М.
Cold Heat? Hot AC? Diagnose Temperature Problems In Your Car or Truck
4:52
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 250 М.
2008 Tundra with heater failure on driver side
12:04
Turning Wrenches Auto Repair & Maintenance
Рет қаралды 29 М.
Old Toyota Tundra VS. New Toyota Tundra. Which One Is Better?
43:14
The Car Care Nut
Рет қаралды 542 М.
2007 Toyota Tundra No Start FIX
17:08
Oz Mechanics
Рет қаралды 40 М.