Anyone starting this project. You do not need to remove the retaining ring on the shaft for the bearing just the ring on the housing. Otherwise this is pretty informative of what to expect.
@dballard86606 жыл бұрын
Specialty tools really make a difference when tackling projects like this. Well done. Good video. Great channel.
@cowboylou18376 жыл бұрын
Great Video! I enjoyed seeing inside the hydraulic chamber!
@stevenpeterson84444 жыл бұрын
using an appropriately sized socket and a vice would help for seating the new seal
@geedubb20055 жыл бұрын
I appreciate you putting this video up. I’ve got my seal already and going to install it tomorrow on my 2600. Dang bushhogs and tillers are hard on them. Thank you!
@YanasaTV5 жыл бұрын
Best of luck! These old tractors need maintenance but are great work horses
@100InchHammer3 жыл бұрын
What you just witnessed is what not to do. This is a very easy job with the most basic proper tools. THEY ARE NOT CALLED "C" CLAMPS! They are snap rings.
@billstmaxx4 жыл бұрын
ouch.. you didn't clean the tractor mating surface.. may as well not have put that gasket on
@davegacke69534 жыл бұрын
Yeah, I hate to say it but that was about everything you shouldn't do when replacing a seal. If you had put it in the correct way would have been about a 20 min job from start to finish. BTW if you had put it in right side up a block of wood over the seal and any kind of hammer tapping it in works a whole lot better.
@johnnelson82576 жыл бұрын
Thank you for the great video. Gives me the courage to get mine done.
@elliottmanning4 жыл бұрын
My 9N PTO has been leaking for 40 years. Think I will keep adding transmission oil for a few more years...
@chuckaustin38175 жыл бұрын
Yes I just reiterated about the spring side. But you knocked the old seal out correct but the knocked the new seal in the same way and that’s why you couldn’t get it to go in without force it to go in the wrong way. The seal has nothing to keep it from walking out. The seal should of been knocked in from the opposite end. Also no need to take off smaller snap ring unless you needed to take the beating completely off the shaft. Watch your video and you will see the mistake you made. I just don’t want someone else installing it the wrong way. You are gonna have problems with the new seal. Just stating the facts but still was a good video.
@chrisbowling75984 жыл бұрын
I never figured out why when working on stuff, people don't take a few minutes to pressure wash it. It makes disassemble a lot cleaner plus you don't contaminate the new parts when reassembly. I'm sure the new seals and bearings would appreciate a clean surface.
@mikeburke8656 Жыл бұрын
I saw the same thing. Good information anyway
@pkhoury121210 ай бұрын
Or at least get a scotch brite pad and some break cleaner to clean the mating surface. I never install a gasket unless the surfaces are clean.
@user-ku3jw7ux2b3 ай бұрын
Just spend some effott and clean the opening where the paper gasket sits..The biggest hassel is the c clip holding the bearing race into the housing. When I was reinstalling it ; it decided to fly off somewhere in my shop. Took me three hours to find it..
@johnraynor5095 Жыл бұрын
Watching that pto shaft run, looked like it wobbled. If bearing is bad, new seal won't last long.
@billyelkins4415 жыл бұрын
You need to invest in a power washer.I never work on anything until its clean.
@donttreadonme43554 жыл бұрын
Especially hydraulic systems
@jeffthomas10632 жыл бұрын
Amen!
@elfamosonerds69666 жыл бұрын
Friend I hope someday to lead the lifestyle that you have greetings from guadalajara Jalisco
@AdarshChand-qv1vb6 ай бұрын
Bula frnd Nice video
@chrismerry8384 жыл бұрын
Dude buy some tools! Seal drivers and retaining ring pliers are not that expensive. Even for good name brand stuff.
@bbbbb8164 жыл бұрын
How long did this job take? Have a fluid change coming up thought it would be a good time to change a weeping seal.
@chuckaustin38175 жыл бұрын
The seal was knocked out from the outside in and you installed the seal from the outside in instead of the inside out. The spring part of the seal goes towards the inside of the tractor. Your seal will probably walk out.
@chuckaustin38175 жыл бұрын
That is why you had such a hard time knocking it in the wrong way. Not trying to knock you I just didn't want someone else to confuse putting the seal in the correct way. Seal should go in with light taps with a bushing driver or even a socket that fits the outer ring of the seal metal surface.
@YanasaTV5 жыл бұрын
If you listen I said “you’ll see a side with a spring, that side should be facing in towards the tractor, the other side faces outward”
@beckyschwantes52873 жыл бұрын
Use a rubber mallet so u don’t damage your equipment. Don’t worry about using a screw driver as a punch.
@buzzsaw3015 жыл бұрын
Same axle as a ford jubilee. I'd imagine that the pto seal and plate gasket would also fit the 3000. You should really press the seal and bearing. Harbor freight sells a 20ton for under $200 so no excuses for not owning one. Great video
@YanasaTV5 жыл бұрын
I don’t have $200
@buzzsaw3015 жыл бұрын
@@YanasaTV that is an excuse. It will save you money in the long run if you have to press hub bearings or trailer bearings. A shop usually gets $20 to press something. Chances are that in about 5 yrs you will be replacing those pto bearings and dust seal.
@JT-qf4it5 жыл бұрын
@@buzzsaw301 Seal can be tapped in if you use the correct size driver. No need for a press on such a small seal. You can also place the seal in the freezer to shrink it. Will go in a lot easier.
@buzzsaw3015 жыл бұрын
@@JT-qf4it great advice, I have tried that on some bearing races in the past. Works reasonably well.
@rumpoh80392 ай бұрын
IT DOES NOT HAVE A TAPERED SPLINE
@rumpoh80392 ай бұрын
THATS NOT HYDAULIC FLUID ITS BASIC NON FOMING ENGNE OIL (AGRI OL)
@jonathantaylor43326 жыл бұрын
Why do remove retaining ring on shaft , your only replacing oil seal and not the bearing
@terrykelly32396 жыл бұрын
Just a few question what year tractor and what transmission is in it 4 or 8 speed , what position was the the PTO selector in Engaged or did Engaged.
@BRWfilms4 жыл бұрын
Engaged on my new Holland 3430
@yamenyamen52193 жыл бұрын
Hey, can we connect the tractor rear power socket to the trailer to help push in the mud and mountain areas if the tractor's rear power takes it in conjunction with the wheels.
@YanasaTV3 жыл бұрын
If your gear ratio on the trailer match the ratio on the rear tires on the tractor... I suppose it could be possible
@yamenyamen52193 жыл бұрын
@@YanasaTVThank you, how can I calculate that tractor tires size 18.4.30 and the trailer 1200 /20
@bradneumann90753 жыл бұрын
Where did you get kit from?
@crusader7775 жыл бұрын
I dump gear oil in mine ! Leaks out a little slower ha
@YanasaTV5 жыл бұрын
That must do wonders to the hydraulic pump 🤔
@noonespecial63865 жыл бұрын
@@YanasaTV doing this to a TO30 today and was watching a few of these vids, not that i need to , been doing these for years,, The old to30 uses 90 wt gear oil
@cowboylou18376 жыл бұрын
You’re wearing that oilskin vest again...
@galesams42052 жыл бұрын
Hey you put the seal in backwards.
@user-ku3jw7ux2b3 ай бұрын
They are not "c clamps" they are called Cir clips" or "snap rings" but they never snap..
@user-ge8iu4yg4t Жыл бұрын
What name and or model number did you use to order? I tried and got the wrong one.
@boatin155 жыл бұрын
Get the proper tools! Screwdrivers and hammers are no substitute for a cheap puller or pry bar. Your pliers to get off the retainers was hilarious! Clean off the tractor before you pull it apart to prevent dirt in the case. Bearing/seal drivers are also cheap about $15 at Harbor Freight. You basically showed every wrong way to replace the seal!