Worked on the plumbing and cranked the pressure washer for the first time on buffer tank!
Пікірлер: 64
@thomasatkins1675 Жыл бұрын
Hey Man, that looks good. Nice and simple. Easy to work on.
@allproexteriorservicesllc5338 Жыл бұрын
Thanks! It has been a productive trailer.
@powerfulimprovements3 жыл бұрын
Nicely done
@allproexteriorservicesllc53383 жыл бұрын
Thanks! A work in progress for sure.
@ga-prowashllc12.53 жыл бұрын
My brother great job on building new system I use a vent cap for Bathroom under a the sink it's has a Built-in check valve no trash can get into your tank I put one on my 330 tote it works great good job on buliding your trailer Road dog dirt relief
@allproexteriorservicesllc53383 жыл бұрын
Thanks. I never thought about vent cap from the bathroom. That is a great idea and may have to use it!! Thanks again
@mauropasillas20547 ай бұрын
Nice set up ty👍
@FamiliaGuevara11 күн бұрын
Can you share a shopping list?
@allproexteriorservicesllc53387 күн бұрын
I do not have a part list unfortunately. Thanks
@thomasatkins1675 Жыл бұрын
I have a question, will the pressure washer still be able to feed from the tote when the water is below the pressure washer line?
@allproexteriorservicesllc5338 Жыл бұрын
The water must be above the bulkhead fitting that feeds the pressure washer. Thanks
@NutcrewGaming3 жыл бұрын
Hey buddy quick question i notice you pressure washer will suck the water up from the tank when you started it. you can see the water flowing from the tube to the tank. But my pressure washer wont do that. i bought the simpson 4400 4 gpm pressure washer and no luck. Can you shed some light?
@allproexteriorservicesllc53383 жыл бұрын
You probably have a direct drive pressure washer. A direct drive pressure washer will not suck water from a tank. You need to raise the tank above the pressure washer to gravity feed. If you get a bely drive or gear drive pressure washer, then they will suck from a tank.
@NutcrewGaming3 жыл бұрын
@@allproexteriorservicesllc5338 yes sir, i do indeed have a direct drive pressure washer. what kind of pressure wash is the honda? is that bely drive or gear drive?
@allproexteriorservicesllc53383 жыл бұрын
@@NutcrewGaming I have a belt & gear drive. I like them both, but the gear drive is growing on me. Thanks
@NutcrewGaming3 жыл бұрын
@@allproexteriorservicesllc5338 awesome, thank you sir
@dantec88548 ай бұрын
What size of filter and clear hose from tank to pump did you use sir?
@allproexteriorservicesllc53387 ай бұрын
1 1/2" for the pressure washer. You could use 1" & that should work. Thanks
@nategarrison992 жыл бұрын
what size is the ball valve going to your pressure washer? looks like 1 inch?
@allproexteriorservicesllc53382 жыл бұрын
Yes it is 1". Thanks
@dcsc48952 жыл бұрын
What size of line are you feeding the pressure washer with ? looks bigger than 5/8" ?
@allproexteriorservicesllc53382 жыл бұрын
That is 1" feed line. Thanks
@braddgullickson99263 жыл бұрын
Very informative videos. I'm thinking about offering pressure/soft washing. This will be my second year mowing lawns and I was just wondering if you're still gonna mow? It sounds like there's more money in washing. I just do this as a side hustle, I work full-time elsewhere. Keep the videos coming. 👍
@allproexteriorservicesllc53383 жыл бұрын
Bradd, I do not plan to mow next season. The pressure washing has a better margin when done right. Make the move and you will not regret it! Thanks for watching
@scottwillis43283 жыл бұрын
Hey brother. Great videos. I have a small lawn care business solo operation. Adding housecwashing next year. Having to devide my trailer basically in half. Half lawn side half downstreaming side. 6x12 trailer so will be tight. What did you end up doing with the spare tire? I'm having that same issue with it having to be taken off the side to accommodate the reels.
@allproexteriorservicesllc53383 жыл бұрын
I was debating on cutting the off the channel in front of the trailer, but decided against that. I also thought about just keeping in back of the truck. But after working the trailer, I think I will move the mount to the other side. I would also recommend that you make the reel rack off the trailer as far as you can to maximize your space. Thanks for watching and let me know if I can help with anything else!
@h2owashpros1543 жыл бұрын
Did you buid those supports for the pressure washer and hose reels yourself? I need to do that for my trailer
@allproexteriorservicesllc53383 жыл бұрын
Yes, I did all the fabrication work. I am in the process of adding another stand for my 8 GPM unit. BTW, I love them being mounted on the back of the trailer for access.
@rayrussell5903 Жыл бұрын
Can i get a list for the plumbing
@allproexteriorservicesllc5338 Жыл бұрын
I don't have a list. I purchased all my plumbing from Home Depot. 2" from the tank and reduced when connected to the machines. Thanks
@brandonh.47813 жыл бұрын
Where did you get the tie downs for the inch tank? The way you bolted it to the trailer?
@allproexteriorservicesllc53383 жыл бұрын
I made them out of angle iron. I didn't like the look of straps. Thanksn
@ohmimprovement57673 жыл бұрын
Its not a street t, it's more like a sanitary t if anything. I've actually never seen one of them in the Chicago area and that's what I've done my whole life lol. Also, if it was me I would remove that 90 you have leading to the pump and use a street 45 into a regular 45 to make it a long sweep for better flow to that pump. A street fitting has one hub and one male end. 2 45's make a 90
@allproexteriorservicesllc53383 жыл бұрын
Sweeping tee vs. a regular tee. It has great flow, but i do need to add a ball valve. Thanks
@properpreparation32133 жыл бұрын
Nice build! Question... what is the bypass hose (valve) for that your run from your pressure washer to your tote? What's it's function?
@allproexteriorservicesllc53383 жыл бұрын
The original bypass hose was connected to unloader & then went to the hoe inlet on the pump. So went you left off the wand, the water recirculates but will eventually heat up. So I disconnected the connection on the inlet and plugged it then ran the bypass hose to the buffer tank. With this set up, it doesn't matter how long I stay off the wand and the water will never get hot in the pump.
@outdoordeerdogs92043 жыл бұрын
What size filters are them that your using
@GoldenState4082 жыл бұрын
Awesome clean build. Can i ask what size is line is feeding your pressure washer?
@allproexteriorservicesllc53382 жыл бұрын
Thanks!! I used a 1" line to feed the 4 GPM unit & 1 1/2" line for my 9 GPM unit.
@GoldenState4082 жыл бұрын
@@allproexteriorservicesllc5338 i like your setup and imma try to replicate that. For a 5.5 gpm do you think i should use 1” or 1-1/2”?
@allproexteriorservicesllc53382 жыл бұрын
@@GoldenState408 1 1" should work perfectly.
@GoldenState4082 жыл бұрын
@@allproexteriorservicesllc5338 thank you Sir! hope you killin it right now
@shawnjacks2072 Жыл бұрын
How did you secure that water tank down
@allproexteriorservicesllc5338 Жыл бұрын
I made some brackets that are bolted to the deck of the trailer. Thanks
@shawnjacks2072 Жыл бұрын
@@allproexteriorservicesllc5338 thanks for the reply I ended up doing 2x4 on all sides two rachet straps over top my welder was willing to make the brackets but the way I did it was much more stout imo I'm now working the plumbing and it's been a real learning lesson haha.
@DIVEBABY643 жыл бұрын
How long is your bypass hose? I have seen some say it needs to 15’ -25’. Also do you run that drop stick almost to the bottom of the tank?
@allproexteriorservicesllc53383 жыл бұрын
My bypass hose is around 3 or 4’. The only time you need a long bypass hose is on a roof pump to cool the water. I have a drop stick in the bulkhead fitting towards to bottom of the tank. Thanks
@zadok222 жыл бұрын
Hey, where did you get the IBC tote clamps to hold down the tank? I have never seen that before. Doing a build right now.
@allproexteriorservicesllc53382 жыл бұрын
I made the hold down clamps out of 2" angle iron. Thanks
@michaelc72833 жыл бұрын
Had a question on your SH tank. Do you manual fill it up? I heard that some SH suppliers won't fill up a tank if you have a drain spicket on the bottom of a tank. It has to be all solid. Just curious. Thanks
@allproexteriorservicesllc53383 жыл бұрын
I fill it myself at the local pool company.
@xtremepowerwashing18153 жыл бұрын
Love the build so far. A few tips I can give u is to definitely get yourself a sh tank with out any bulk head fitting at the bottom, the sh will eat those seals in no time and destroy your trailer..been there already..use that tank for your soap tank..def put a bigger beather hole in that tsnk... when I had a IBC tank I had about a 1/2 inch hole at the top and never had a problem with the debris getting in. Looking good. 👍🏻
@allproexteriorservicesllc53383 жыл бұрын
Thanks for the tips! Much appreciated. I will replace the SH tank hopefully soon. I did some more work today to bring it all together.
@xtremepowerwashing18153 жыл бұрын
@@allproexteriorservicesllc5338 Awesome.. and your welcome..
@maxsherro87293 жыл бұрын
Hey brother, great video. I have the same washer how are you getting by without using a pump to push wasted to your washer?
@allproexteriorservicesllc53383 жыл бұрын
The belt drive machines suck water with no problem. Thanks!!
@maxsherro87293 жыл бұрын
No way that’s awesome I did not know that!
@maxsherro87293 жыл бұрын
Anyway you could post a list on some of these items?
@allproexteriorservicesllc53383 жыл бұрын
@@maxsherro8729 It would be tough. Feel free to reach out to me for assistance.
@maxsherro87293 жыл бұрын
Ok thanks!
@zadok222 жыл бұрын
Just saw the first video. What will your fab guy charge to send me 4 of those IBC tote hold down clamps?
@allproexteriorservicesllc53382 жыл бұрын
Not sure. I can ask him when I see him again. you may want to look for a local fabricator. Thanks