As mentioned no service manual available at time this video made… 2024 TransAlp service manual lists 25 N-m (18 lbf-ft) as torque value for bottom bridge pinch bolts… Thanks for the incredible video!
@berticusmaximus83818 ай бұрын
Great video and I like that you put the actual lighting test first.
@3dcycleparts8 ай бұрын
We're learning. Always more to improve on. Thanks for the feedback!
@Wheelo40Ай бұрын
Hey one of the great instructional videos. Thanks. You definitely sold a set of lights! I read the comments and deleted a question about having both the lights and the 12 volt plug. You sell a splitter. Thanks again.
@3dcyclepartsАй бұрын
Thank you! Yes, you can run both, you'll just need our splitter so they can be connected behind the cluster.
@human15138 ай бұрын
Very thorough explanation.👍
@user-xm9lh3ze1p5 ай бұрын
Would be great if you had something for the rear tail and brake lights. LED brake strobe module? Not enough lights on back.
@garethgay91338 ай бұрын
you guys are amazing
@3dcycleparts8 ай бұрын
Well thanks! We try our best.
@nasadiora2 ай бұрын
hola donde puedo comprar esos focos ?
@patkennedy19 ай бұрын
A nice clear video, and appears to overcome one of the shortcomings of the Transalp - it's abysmal headlight performance. Plus your mounting means that we can have the lights without the big upper crash bars. Just a couple of questions. Firstly, does this system mean the 12V accessory plug cannot be fitted, or is there room to fit both to the connector behind the gauges, which the accessory plug also employs? And secondly, how much does the conversion kit weigh, for the weight-conscious? Also, if I may just add - tightening one pinch bolt of a pair can affect the tension on the other bolt, such that after torquing the second bolt to spec, the first one's tension should be re-checked. Sorry to be picky...
@3dcycleparts8 ай бұрын
Thanks for your feedback and questions. I believe the total weight is between 2 and 3 pounds but I'll have to double check. We make a splitter that allows you to run two electrical accessories off of that front connector. With that you can run the lights and the 12v outlet. I just need to get those up on the website.
@meinungsfreiheit202328 күн бұрын
can then the fog lights be switched on and off on the dash, or is there a separate switch /button to install?
@jeanjacqueslebrard35298 ай бұрын
Bonjour excellente vidéo et super montage pour les feux Combien coûte le kit J'habite en France Merci d'avance
@markchoitz4439 ай бұрын
great install video, can you mount these on Hepco/Becker crash bars? Or do you have another light assembly that will do so? Thanks
@3dcycleparts9 ай бұрын
You could do that, you'd just have to get crash bar mounts of your choosing if you wanted to change up the mounting. Denali makes some nice ones.
@NinjaHorns8 ай бұрын
How many hours are the lights rated for?
@tomekes65844 ай бұрын
Thanks for the vid manual. I have a 12v socket and heated grips (both Honda's) - is it still possible to install these lights in my bike? Or do I need a power splitter?
@3dcycleparts4 ай бұрын
You would need our splitter to run the 12v outlet and the light kit together. The OEM heated grips have dedicated connectors on the bike. Thanks
@tomekes65844 ай бұрын
@@3dcycleparts thanks for explaining. Great you have the splitter as a product.
@KairyuRider4 ай бұрын
Do you sell just the wiring and mounts? I have lights that I like.
@3dcycleparts4 ай бұрын
Yes, they're both listed on our website. Thanks
@andygravesstructures45657 ай бұрын
I ride in NYC, and pot holes are horrible. I want a set of these auxiliary lights to run all the time, high or low beam. Focused more at the area in front of the bike. Can your harness accommodate that set up?
@3dcycleparts7 ай бұрын
We can build a harness that does that, it would have to be specific to the lights you're gonna run. Email support@3dcycleparts.com with what dual intensity lights you're gonna run and we can go from there. Or we can build the whole system for you.
@b.toscano41487 ай бұрын
Hello guys. Thank you for your video, it's very useful. Question: I can see the engine error light on the top left corner of the screen within the first seconds of the video, when you're showing the brightness of the lights outside. I believe it comes up because the CANbus spots an additional device/circuit. I also believe you have sorted it out and got ride of the error. Did you have to plug the bike to a diagnostic device and erase it or was it just an intermittent error that went away automatically? Or am I completely wrong? (That's very possible too) Thanks again!
@3dcycleparts7 ай бұрын
The lights do not cause any check engine lights to come on. We were developing 6-8 products at once and something else we did had triggered the light and I didn't realize it was on until editing the video. Thanks
@b.toscano41487 ай бұрын
@@3dcycleparts Thank you very much for your reply 👍🏻
@marcofrancardi1055 ай бұрын
hi there. I wonder if you can help me. I damaged the bottom front light Six pins connector plug. Iknow it's a sumitomo sealed plug, but I can't find the proper model specs. Is there any code by wich it is idendified? Thank you for your help.
@3dcycleparts5 ай бұрын
Email me a picture of your damaged connector to support@3dcycleparts.com
@nateskeen82175 ай бұрын
Since this kit uses the accessory power port.. does it have a pass through to allow the installation of the OEM Honda 12v plug?
@3dcycleparts5 ай бұрын
We have a splitter adapter on the website! www.3dcycleparts.com/2024-up-Honda-Transalp-XL750-Auxiliary-Power-Splitter-p613407023
@nateskeen82175 ай бұрын
@@3dcycleparts awesome, thanks so much!!
@RevansNightmare6 ай бұрын
Do you know if the light kit and power plug will be compatible with the VERIDIAN cruise control
@desertracer22545 ай бұрын
It will. I have both on my '24 Transalp.
@janoseperjessy17299 ай бұрын
Doesn't it blind the oncoming traffic?
@3dcycleparts9 ай бұрын
If you had your high beams on it would. You should never have your high beams on when there is other traffic around though.
@garrystacey99258 ай бұрын
Cannot find a connector under the seat, American and Australian market different?
@Grasshoppa978 ай бұрын
It’s in the far back. Behind the tool kit. Has a soft rubber protective cover
@irarabesc3 ай бұрын
yep, they are different
@brigitteduclos72646 ай бұрын
Quel cite vend ce prouit merci
@centralcoastcruiser20846 ай бұрын
Wish you had full time running lights not just high beam so to be seen better in the daytime.
@3dcycleparts6 ай бұрын
We run the high beams in the daytime. Why would you need to run low beams during the day?
@centralcoastcruiser20846 ай бұрын
@@3dcycleparts maybe you can run your high beams all the time but many auxiliary lights are too bright to run on high beam full time and it is better to run low beam. The object is to be seen better during the daytime and at night switch between low and high. Anyway, that is what I'm looking for.
@garethgay91338 ай бұрын
do you make one for the honda 750 X-ADV? please say yes
@3dcycleparts8 ай бұрын
We don't. Sorry!
@garethgay91338 ай бұрын
oh pity @@3dcycleparts. I use my x-adv all the time and the roads here Sardinia are not lit and are very bendy
@fox111qc9 ай бұрын
I don't understand why the fuse get plugged in the accessory plug under the seat.
@3dcycleparts8 ай бұрын
It's an open circuit that must be closed there to get power up front. That how Honda designed it, I've got some ideas as to why but it would just be speculation. Thanks!
@irarabesc8 ай бұрын
It’s specific to the US version of the bike that has two acc sockets, the first is under the front dash and the second is under the seat. But only one of the sockets can be used a time, the other socket has to be shortened. The EU version of the bike has only one acc socket that is under the front dash, it doesn’t need any shortening.
@gronno5 ай бұрын
EU spec has a power outlet under the rear seat, USB C type.