Ford E4OD / 4R100 Class lesson 12 of 16

[@danieldeardorff1]

This is the best, most organised, thoughtful teacher and class of any kind I know of. He makes this complex job seem simple and fills me with confidence. I have taken many classes of many kinds up to and including graduate school in sciences - and while there were good teachers in some, none were better. Than this.

[@johnknight2336]

OK.....If you bought the Transgo kit and you don't have a foot press....DO NOT USE ITS SPIRAL SNAP RING!!!!! Its NOT the same as the Sonnax one from the kit PN# 36744-01. Gentlemen, I fought the Transgo unit for 2+ hours till I laid it out side by side next to the Sonnax one. Its a smaller diameter, slightly thicker, and is a total PIA!!!!! Mr. Willimas is definitely installing the Sonnax unit from the kit in the video. It IS possible to do this with a large flathead screwdriver BUT....... I had a much easier time when I switched to a medium sized prybar. Makes it MUCH easier to press down a spring finger WHILE shoving the ring in the slot with the edge!!!!! DONT GIVE UP!!!!! DONT GO 1/2 @$$ and put in the old snap ring!!!! YOU CAN DO IT!

[@mariopalomo5423]

The spiral snap ring is essential guys. Its not worth installing the original. Your R&R guy will appreciate it. Your name goes behind your work.

[@johnknight2336]

Seriously...with the work you've done up to this point....Why go 1/2 A$$ now?

[@timothyrials3834]

EBay has a transmission spring compression tool for 30 bucks. It took me 2-3 minutes to put the upgraded snap ring in.

[@dereksasquatchgarletts7924]

Isn't there supposed to be a snap ring to help hold the center support in? I didn't see him install one, just the bolts.

[@kyaneslace3595]

For those who can't make the tool to compress the ring you can lay a 2x4 across the case and wrap some wire around it and bell housing bolt holes and use a small bottle jack to press it down.

[@AlbertoAmezcua-vp2jy]

Master may respect

[@johnrodriguez473]

Why didn't you use the sonnax center support shim, it was in the bolt kit? It'll keep the valve body from warping

[@gravillr]

ATSG manual says to check the clearence on the overdrive clutch backing plate to case "selective" snap ring. My snap ring is 0.080" and the gap is 0.085" for a total of 0.165". ATSG manual suggests I get part# "e9tz-7b421-da" at 0.120" thickness bringing my gap to 0.045" within the 0.032-0.058" range that is required. This video does not mention any of that, and I cannot find that part. How critical is this tolerance and can I re-use the original snap ring that leave a gap with excessive tolerance?

[@josevivas6006]

Ablando es pañol

[@salvadorreyes3482]

My dad's been building for over 40 years and says the replacement center support bolts are cheap and reuse original bolts

[@leeharmon9600]

upon rebuilding my 2003 4r100 (diesel) overdrive clutch pack, I found that it only contained 2 clutches and 2 plates instead of 3. You mentioned the diesel version contained 3. My failure was within the overdrive assembly. Was this assembly possibly installed by someone else or was their a certain year they only used 2 ?

[@stevenbauman3501]

Mine also has only 2 🤔

[@kopfjager6833]

I've been trying to install the snap ring for the large intermediate piston and I can't compress the return spring enough so that the snap ring can fit into its groove. I'm not sure the cause of the problem but it looks like if the piston would move another.015 thou the snap ring could fit. I am physically unable to compress the spring anymore because the tool starts warping. Does anyone have any advice on how to fix this? Ive pulled everything out and tried to reassemble it but that still didn't help.

[@jakegandy6375]

having the same problems what did you come up with?

[@jgr33n1974]

I know this is old. If you’re talking about the intermediate piston just forward of the center support (some people online get the forward, direct, and intermediate assembly snap rings mixed up in part descriptions). I’d check to make sure you didn’t use the 3 .125” thick steels in the intermediate clutch pack. If you’ve got an e4od from before 99 or so, there are 2 sets of steels in the kit he sells (most kits). Make sure you compare your steels and use the ones from the kit which match yours. Mine took 2 thinner steels from the kit and one .125” apply steel from the kit.

[@kevinrourke1373]

I need a video on a aod 88 mustang no

[@airplanemechanic5561]

What tool can you use if you do not have a foot press to install the overdrive clutch spring snap ring?

[@ronsmith6233]

If you were to use the old center support snap ring, what are the indications that the snap ring has come out of the grove with the transmission installed?

[@malcommooney8086]

it wont move, that happened to mine

[@dannyeckelman8777]

Will the early model 99 4r100 change into the 2002 ford f:350 4r100

[@digibeanreparationdordinat4837]

Nope. Just found out myself.

[@bcwoods360]

can you also include some of the older gm models, 350, 400 , 700r4, while there are other videos out there, you have a good presentation with superior knowledge

[@icyuranus404]

go to his website and his videos come with a kit or you can purchase separately. i am amazed that this golden presentation is available for free right now this is tech school quality

[@СергейКлепицкий-ц4ч]

Люблю видео где все изложено последовательно и ясно. Отлично