Trol-A-Matic - Easy Installation - Part 2 of 3

The installation of a Trol-A-Matic on a Honda Outboard.
I have created this page to share information with the hopes of helping you become a better fisherman and catch more fish. I do this with the heart of a teacher in mind while trying to make it simple and fun for anyone!
Thanks for watching and reply below if you have any questions. I answer all questions.
Be sure to subscribe and like the video!
You can follow me at these other sites as well:
Facebook - / fishingeducator
Twitter - / fishingeducator
Instagram - / fishingeducator
KZbin - / jerdog8574
Good Fishing!
The Fishing Educator

[@kellycase5593]

Cover the prop shaft when you're drilling to keep the chips out. Wear some glasses for the same reason.

[@TheFishingEducator]

Great tip, thank you.

[@markcameroon6613]

i had to replace 2 of the screws they broke on me i put mine on a 5.0 liter merc 305 inboard 260hp am i safe havent ran it yet

[@TheFishingEducator]

How did the screws break?

[@roymcpherson7487]

Are there any concerns going into reverse with the plate ? Thanks!

[@TheFishingEducator]

None that I have experienced...just have to use more RPM's to navigate.

[@jpprind]

Do you by chance have a part number for the troll a matic? I have the same Honda 40 horse motor.

[@TheFishingEducator]

Here is the link on Cabela's: www.cabelas.com/product/Trol-A-Matic-Trolling-Plate/699629.uts?productVariantId=1186025&WT.tsrc=PPC&WT.mc_id=GoogleProductAds&WT.z_mc_id1=00000349&rid=20&ds_rl=1252079&gclid=Cj0KCQiA2snUBRDfARIsAIGfpqGHzTjUvKd5mOSllLrs3EUouOkAIZw1fdOEJdIT9i0RP_vhY4u_s9UaAlk6EALw_wcB&gclsrc=aw.ds

[@fishbustin7926]

I wish I could install these without drilling holes in my brand new boat motor.

[@TheFishingEducator]

I completely understand. It is a hard decision.

[@alm4236]

Do you know how far back from the prop I should mount the Trol A Matic?

[@TheFishingEducator]

Put it back as far as you can, but mount it so that there is plenty of of lower unit fin as this will be under A LOT of torque.

[@jasonfox2546]

Why not put trol a matic upside down so you can mark the holes on top then drill down without removing prop?

[@TheFishingEducator]

I guess you could try that. Good idea!

[@ortega2424]

Do you like it? What are you overall thoughts? Does this unit allow you to raise it?

[@TheFishingEducator]

I like it...easy to install and use...allows for super slow speeds and no loss of performance. No, it only raises as water pushes it up as you move through the water.

[@ortega2424]

@@TheFishingEducator Thank you for the follow-up!

[@edwardtomlin8592]

Could you tell if it also helped like a hydro foil?

[@TheFishingEducator]

No...it does not...the two products are different for different applications. All the best.

[@georgebecerra6572]

How does it steer when coming into docks?

[@TheFishingEducator]

It steers good...just goes slower.

[@johnw2120]

It's a pain in the butt when there is any wind.

[@georgebecerra6572]

@@johnw2120 thanks!

[@keithlynchard6333]

Safety glasses

[@TheFishingEducator]

Good tip, thanks!

[@paulsmith5213]

Good job bad safety

[@TheFishingEducator]

Thanks, I think.