Most of the time, clearing the port leading to the ignitor will fix the problem. But, if your stove has been in use for a few years, you might need to replace the ignitors. This tutorial will take you through all of those steps.
Пікірлер: 60
@johnjude268510 ай бұрын
Lots of information and hints should be easier after watching and learning from you Thanks
@MrDilley7778 ай бұрын
One thing that I don't understand is when you tried the old ignitor at the beginning, it was clearly sparking, so explain why changing the igniters with new ones that spark too like the old ones, why didn't the old ones light the burner?????????? Don't you see that does not make sense!!!!!!!!!!!! 😮😊😅😂😢 I'm so confused. Hardy, har. Har, Har, can somebody explain that to me.
@HomeImproveman8 ай бұрын
over time, the igniters wear down, just like a spark plug. If you have ever put in a spark plug, you may have set the gap and those gaps must be accurate to 100ths of an inch. Being slightly off will impact the quality of the spark. You may still have spark but it is not strong enough to ignite the gas. The new igniters tips were noticeably larger than the ones I removed so I would guess that the spark was weaker. I am not expert and this is my own guess.
@trixienuno528Ай бұрын
Thank you! I used the safety pin method and it worked like a charm. 😄
@TheMaxAwesome4 ай бұрын
Sometimes it is not the igniter. Best thing to do when troubleshooting is swap out all the parts one by one to identify the root cause. In the case of a range, you have the igniter, which is a pain to swap, the base that channels the gas, and the plate that covers the base. These last two are easy to swap with any other burner that is the same size. In a recent case, I found that my igniter and plate were fine, but the base was either worn down or warped, and therefore not channeling gas the right way. Replacing the igniter would have been a huge waste of time and money!
@kueichenglee75832 ай бұрын
Thank you
@RickL_was_here25 күн бұрын
I just swapped out an igniter for a client on his Fisher Paykel that the cleaning lady broke. This happened a long time ago so the thing wasn't used. Everything was fairly greasy so there was some cleaning involved. Anyway, the thing wouldn't light even though I could clearly see the spark and could smell the gas. I used a bbq lighter to test for gas dispersal and everything looked fine.... There was a gasket that separated the burner base from the entire top cover and it was badly damaged so I have him getting one of those in case it's a leak causing the issue and will try again. If I remember, I'll come back to share the result and/or possibly a solution.
@12lesfloАй бұрын
One suggestion is to take a picture before you disassemble the items.
@ScottShimamoto3 ай бұрын
I ABSOLUTELY LOVE that the burner screws and the screws underneath were different sizes.. There is ABSOLUTELY no reason for that other than some product designer was STUPID!!! haha
@Eclectic83 ай бұрын
Or intentional. I've had to replace some of those bolts and they were very unique and, though small, very expensive.
@ScottShimamoto3 ай бұрын
@@Eclectic8 the keep it simple stupid principle has been ignored since the beginning of human history
@RickL_was_here25 күн бұрын
I'm not a fan of engineers.... At all. Working as a sparky, working on vehicles, just repairing stuff. These people need to be forced to do 6 months working on whatever it is they intend to be designing. Frig.
@scottshimamotomortgage94624 күн бұрын
@@RickL_was_here haha.. that would be a fitting punishment!!
@amvillegas52 ай бұрын
Cleaning the channels and the secret hole above the igniter did the trick for my stove. Thank you so much for your video!
@HomeImproveman2 ай бұрын
❤ the "secret hole." Glad it helped.
@collinfleming93837 ай бұрын
Very helpful, thanks!!
@omara97719 ай бұрын
Hi hey you help me with this video thanks
@JosePerez-yg6mp6 ай бұрын
You Da Man! Struggling for the longest time with two of my burners and never knew about the little hole. Fixed it right up. Thank you so much for sharing.
@gordonellisjr3317 ай бұрын
I agree 100% with your view of becoming a rely on someone else society. I am the eldest son of a do it yourselfer and was the mandatory gofer/ helper whenever there was a project to be done. I am very grateful as the lessons I learned early on have only helped me along in my life. It has made me who I am today. I appreciate the video as I was curious what was involved with the igniter replacement. I did a quick google part search before finding this video and saw the assembly you refer to in the video which got me wondering why I would need all of those parts to replace an igniter. Again thank you for the valuable information.
@HomeImproveman7 ай бұрын
It's nice to know that these videos are appreciated. Thank you for your comment.
@smwrbd2 ай бұрын
Good job. I appreciate you leaving the mistake in . 😊
@LT546563 ай бұрын
This is exactly the video I needed to watch. Now I just need to see if I can locate the parts I need to replace! 😊
@dudleywood94144 ай бұрын
I did exactly what you said and I am very thankful for your advice. The burners work perfectly! Again thank you.
@HomeImproveman4 ай бұрын
You're welcome!
@carlosj458126 күн бұрын
Excellent video, can you please share the ebay link. I have the same stove model. Thank you
@HomeImproveman26 күн бұрын
The exact link is gone, the seller must have pulled it, but this looks like a similar item, www.ebay.com/itm/375346146447?
@rafjones9 ай бұрын
Very helpful. Thank you for posting this.
@stargazer00014 ай бұрын
Totally skipped the part where you show how to remove the igniter from the frame..
@RickL_was_here25 күн бұрын
The one I just did had a little metal 'A' shaped piece that I had to squeeze the two sides together and pull it out, releasing the ignitor.
@pppauliii1 Жыл бұрын
Well done video. And a nice call to action. thanks
@traceymanzano401519 сағат бұрын
Electrobe change
@tellsthetruth8947 ай бұрын
Thank you for this excellent video. Your oven range design is nearly identical to mine. I am glad you showed that the burners have to be removed to raise the top by removing the two screws in the base of the burner. My front left burner that is used mostly will not ignite the gas unless another burner is sparking. Unfortunately, the head of 1 of the 2 screws in that burner had sheared off, making it impossible for me to remove, especially because the top of the shaft is below the surface. If you have any suggestion on how to remove the headless screw it would be soooo much appreciated. The anealed/hardened shaft of these screws is so small that it's very hard to drill into it. Your help in how to remove this headless screw shaft will be very much appreciated. Thank you
@HomeImproveman7 ай бұрын
That's a tough situation to find yourself in. Unfortunately, appliance repair is not my specialty. Good luck.
@g.borgia5100Ай бұрын
Google that problem, many have had the same, and a solution must have been found
@kueichenglee75832 ай бұрын
Thank you
@craighendrickson79382 ай бұрын
Why won’t anybody take off the piece after they take off the cap? As if it’s not just laying on there too?
@DemocracyDiesInDarkness9 ай бұрын
This was exactly my problem! Thank you for posting this very helpful video.
@willyD2002 ай бұрын
What name stove arr you working on ?
@gardeningwithkirk3 ай бұрын
❤❤❤Good morning from Gardening with kirk
@mattd77707 ай бұрын
Safety pin in the gas hole fixed it for me. Thanks!
@teymurgulmammadov78009 ай бұрын
14:09 thanks from Baku.
@leslowell588 ай бұрын
Thks, good job. Got a lot from video.
@johnkhuumailbox4 ай бұрын
hi, I have the same stove model but could not find the igniter part number on the part list. Can you please send me the ebay store address which you bought the igniter. Thanks.
@HomeImproveman4 ай бұрын
The item listing on ebay is gone, but this was the title of the listing - Frigidaire Range Ignitor P# 316536602 316536614 316536610 316536600 316536622
@g.borgia5100Ай бұрын
The company does not sell just the ignitor, as he mentioned in the video. They sell only the whole burner unit for about $100.00. That's why he bought the ignitors from ebay
@greenthumb47556 ай бұрын
If the igniter is sparking why would you replace it?
@HomeImproveman6 ай бұрын
just like a spark plug in a car, the distance between the electrodes increase over time and usage. Spark may still be there, but it is weaker because of the increased distance. Clearly, the choice to replace them was the correct choice because it solved the problem.
@sharonmiller1899 Жыл бұрын
Thanks for this. Couldn't find the port but scrubbed the silver piece and that did the trick.
@bethperrotta7 ай бұрын
If I have propane gas, can I just turn off the tank out side?
@HomeImproveman7 ай бұрын
That will work, just be sure to turn on one of the heating elements to give the gas that is stuck in the line an opportunity to escape. Hold a flame up to the heating element to ensure that the gas is completely off. You should also have a valve behind the stove that you can use to shut off the gas..
@km62063 ай бұрын
not clear why you can't try cleaning the igniter before you replace it.
@HomeImproveman3 ай бұрын
Definitely try this, but a quick examination will often show this is futile. Propane and natural gas burn cleanly and leave no discernible residue to foul the igniter and because the igniter is recessed, it is rarely soiled by food.
@g.borgia5100Ай бұрын
Looking at both ignitors he holds up. The new one has a little pin at the top which has worn off the part that doesn't work
@alittax10 ай бұрын
Shouldn't you have turned off the electricity and gas to the stove?
@HomeImproveman10 ай бұрын
You are correct, I should have mentioned turning off the gas. But, you need to keep it plugged in so that you can see the ignitor attempting to spark. While replacing the components, you could unplug the unit, but the only time there is electricity going to the ignitors is when you have the knob turned to 'light' and the voltage is quite low.
@davidhuang57339 ай бұрын
Do u need to turn off gas completely to replace the igniter?
@JivaJavaCafe9 ай бұрын
No, but to be safe it is a good idea. If it is difficult to access the gas shutoff, you can leave it on, but be very careful of moving the control knobs while doing the work. In fact, if you must leave the gas on, put tape over the gas knobs so that they do not move while you are working.
@AnthonyPaul-fq5tk Жыл бұрын
eBay doesn’t show just the igniter without the other assemble. Can you send me the name of the vendor you received just the igniters?
@HomeImproveman Жыл бұрын
I believe this is the one - www.ebay.com/itm/325831101176?hash=item4bdd0c0af8:g:umQAAOSwgZJfd26X&amdata=enc%3AAQAIAAABAKMqB5iuVvvpvEE60ZfDvtcvxPz5HqfeZFOecLTuvnLNaBLyz02pjTJU7CNucc30wSowhX%2Fy97A9%2BAa9uoZzfK64KvNNjipGbwY19q6NRQgcoeMUXnB6Zv%2BQqMkwL9Eo8LS3Gp4ddZFuCwPi429uszzaOOqIIJLH9neOcxdEAvigHGHvy%2B%2FVycjDqdUgzabKsQaDcm8yDZritnIs%2BUVYVWsNdg19wR3MyWbZUVYGMdTjuspsnSNn9k4yVsg%2B9T3XE0qJ9A2upAahQ8uvTfUSTkLe4dHXHfLV5jwpvWwxH37eYXtynP%2BnVq6csUkIQF5KAZRUDl3qv98VLrwlb1Uy5Z4%3D%7Ctkp%3ABk9SR8bUv5XeYg
@g.borgia5100Ай бұрын
The vendor was not a company. An individual, I believe, because the ad has been removed