Troubleshooting Backup Sensors

Troubleshooting and replacing backup sensors on a 2006 Ford F250 truck, but information is applicable to most backup sensor systems.

[@GradivusAres]

6 years later and your video still helping people. Thanks for the video man

[@mark502]

7 now 👏🏼👏🏼

[@villi6505]

I just bought a used 2006 F150 to which the dealer quoted over $500 to even attempt to trouble shoot the backup sensors that were not working. Offered up an aftermarket back up camera for $150 in place of repairing the factory system. With your video and recommendation to avoid the factory parts counter, ended up with the new backup camera plus repaired the backup sensor system for just under $40. Thank you greatly. I will be checking your posts for other mechanical questions.

[@newell2339]

Thanks for posting. Fixed my 2003 F250 using this technique. My inner 2 sensors failed after roughly 2 years (circa 2005) and I never bothered to fix the system. Decided to. Ordered a 4 pack of sensors from e-bay for ~ $21 and that included free shipping. So far so good. A couple install notes: On this make model, the inner 2 sensors are slightly more difficult to get access to due to the position of the spare tire support, but still easy. My original part numbers were 3F23-15K859-BA. The replacements were 4F23-15K859-AA but the e-bay website had a make/model checker and reported this was a suitable substitute; i.e. it should fit. Externally all the replacements fit perfectly in the bumper holder and the holding clips worked fine too. The only slight difference was the near the inner sleeve around the 3 power prongs. There was enough of a difference that the power cable didn't slide in and latch like you would expect from OEM, but with a little coaxing, I was able to get it in and latched. I also used a slight amount of dielectric grease for the reassemble. Still working after a couple days. Unless you have significant hearing problems, you don't need any tools or "listening devices" to hear the clicking sounds when troubleshooting. He only used what he did to help shoot the video... Nice job and thanks for taking the time to share it.

[@KILLER9676]

Used this guide to detect fault and fix sensor on Jaguar X-Type. Once I could hear which sensor was defective, I ordered a single sensor from eBay and replaced in about 3 mins. Saved myself a fortune! Thanks

[@DeathScouter]

Steve A Glad to hear it! I love knowing that my videos are helping people out.

[@myklein75]

Thank you for the informative video. I just bought a "new" 2006 F350. The backup alarm did not work. After watching your video I ordered 4 sensors on ebay for $41.00. After receiving, I tested and discovered only one was bad. I changed it first, problem solved. It took me longer to get my small screwdriver, creeper and flashlight out, than it took to repair the sensor. Thanks again!!!

[@DeathScouter]

myklein75 Great! That's the reason I make these videos. So many repairs seem intimidating and all we need is someone to show us how easy they actually are.

[@bubbatennessee7531]

Thanks bro ! I used your trick to find out the dead sensor on my 05 Nissan Titan. The ticking sound is really faint, I used a paper tube between my ear and a sensor to hear the sound. Thanks again, now I only need to buy ONE, instead of four, replacement sensor.

[@jspry4800]

Many thanks, DeathScouter! I just picked up a 00 Excursion and the parking system is non-functioning. Definitely saved me a lot of troubleshooting. Shout out to Hans C. as well, the phone app worked like a charm!

[@kathleenwilson8948]

Watched your video, figured out which sensor was bad, and ordered the part from Amazon. I just replaced the bad one in 5 minutes following your instructions. Thanks!!

[@DeathScouter]

+Kathleen Wilson Awesome! I'm so glad to hear my videos are useful.

[@noinsertnamehere3460]

+DeathScouter Myself as well! Thank you!

[@devanthomas3859]

Thanks for sharing. This is my exact problem - 2006 F250 with 3 malfunctioning sensors. Same deal with my dealer - they wanted about $160 each and I bought all 4 from China on eBay for $48 total. They'll take a couple of weeks to get here, but well worth it.

[@lesballard7682]

Excellent, worked perfectly fine, 3 of the 4 on my 06 Freestar clicked, one did not, removed the rear fascia, swapped it out and the back up assist works perfectly fine. It was just that simple and easy and I'm sure about $300-$400 at a certified shop

[@suncrestbuilders]

Wow! I ordered the part online and just installed the new sensor myself. I'm pretty sure you saved me hundreds of dollars. Thank you!!!

[@DeathScouter]

Julie Johnson You definitely saved yourself a lot of money. Well done!

[@DC-nd7qz]

I kept thinking that my glasses were fogged up while watching this video

[@danmadigan6930]

Traced to speaker on PAM module and was bad put temp speaker in and it works. Will get Ford speaker for $20 on ebay. What a pain but fixed. Thanks for the information and help

[@DeathScouter]

As I said in the video, the inductance wand I used was to amplify the sound so it could be heard on the video. If you put your ear down to the sensors and cover them (to simulate backing too close to something) you should be able to hear the ticking with the "naked" ear.

[@lasershow215]

+DeathScouter how have they heald up over time? I'm looking to replace mine with the ebay ones

[@DeathScouter]

+Bill Kelso I did have a sensor fail after about a year. I ordered a 2nd set of 4 (still only $35) but this time I didn't bother with my wand since I discovered how easy it is to simply swap the sensors. I decided to replace 2 and re-tested the system. If it was fixed (and it was) I would keep 2 new ones as spares. If it wasn't fixed, I would roll the 2 I took out with the remaining 2 (and still be able to keep 2 new ones as spares). SO, to your question, 1 of the 4 ebay specials didn't last more than a year.... but I don't know how that compares to "Genuine Ford".

[@DeathScouter]

No issues so far. Since the original video, I replaced 2 (suspect only 1 was bad, but replaced them in pairs to speed up troubleshooting). So far, so good.

[@charlesthomas8383]

My backup sensors went out about 3 years ago and I took it to the dealer. It cost me $260. What a fool I was. This time, I ordered the parts (set of 4) for $39. I checked out the video and did it myself. As far as I know they replaced one sensor. The first sensor I replaced fixed the problem and now I have three spares for the next time one goes out. It should be against the law for them to charged $260 for a 2 minute job and a $10 part.

[@DeathScouter]

Knowledge is power. So glad my video helped you out! What a great way to start the new year.

[@aundraharris2158]

Thanks good video I fix my own

[@lochlanabdullah5937]

i guess it is quite randomly asking but do anyone know of a good site to watch newly released tv shows online?

[@jazielkamryn7735]

@Lochlan Abdullah I watch on FlixZone. You can find it on google :)

[@simoncolson3503]

@Jaziel Kamryn Yea, have been using FlixZone for since march myself :D

[@bobbystanley8580]

Thank you so much for taking the time to make this video!

[@ldynasty.5024]

Great video. Helped me a lot. Thank you.

[@brucewalters8974]

DeathScouter.... Thanks for the troubleshooting video on the backup sensors. After watching it, I followed your instructions to check out the sensors. I don't have the amplifier, but was a relatively quiet place when testing. What I found was that I didn't hear anything from ANY of the sensors. I could presume that perhaps all four sensors are bad, but before ordering new ones, I was wondering if and what else I might check just to make sure it not something other than the sensors. Any help would be greatly appreciated.Thanks....

[@victormorales9150]

My light slip and vdc and brake is on can u mahe bideo for fix that

[@nycalix]

Thank you for the video it help a lot in diagnosing the faulty sensor on my Mountaineer

[@richshorter1969]

Thanks! Now I know what the problem is. I pulled it out pretty easily, but I don't have a replacement yet.

[@annehoffman960]

I just had a sensor replaced at the dealership under warranty. Do you know if there's any reason the taillight would have been removed? I have a 2014 f150 with the backup camera and sensors.

[@pmedina701]

thanks for the info. 2003 f250 with same issue. gonna buy some sensors next week :)

[@driftaaja5383]

Thank you for making this video! lets see if changing the sensor works!

[@robertrowlin9854]

I’m having the same trouble with my 2006 f350 lariat dually. I’m going to get the sensors too and do mine thanx for the tip.👍🏻

[@robertrowlin9854]

Blue f150 is gone my f350 is gun metal gray l

[@DeathScouter]

A set of 4 from ebay remain cheaper than a single one (plus labor) from the dealer. As the sensors are the most common problem, I would say that starting with a sensor swap is your best bet. Thanks for watching.

[@Mike38901]

Thank you for this!! Very very helpful information, saved me money

[@hansc.242]

You do NOT need the Inductance Tool !! I just find out that you get the same Results with a Cellphone and the (Android) App SUPER EAR OIDO from Liberation Studios. Plug in your Earphones and hold te Microphone of the Cell in Front of the Sensor. Move around a little bit. If the Sensor is Good = you hear a rapid ticking Noise. If not = the Sensor is dead. Have a nice Day

[@DeathScouter]

That's cool. I didn't know that app existed. Thanks for contributing to the discussion! Was the app free??

[@hansc.242]

Yes. At least the Androidversion is. Don't know about apple

[@TheOGRobertCarrasco]

Thank you for sharing this tip!!

[@terrygrant3206]

;the hole on the side of your head works just as well. and does not require batteries.

[@aishaabdullah2385]

Hans C. Thanks

[@StephenMattison66]

04:12 Neat trick your camera did there as you panned the Sun it overlayed a black dot over the Sun. I'm wondering if this is just for the viewer's pleasure or if it's actually a way to protect the camera...

[@isabelalvarado6845]

I have a Ford Expedition. my sensors gave been working fine until 2 days ago. It just keeps beeping and nothing is behind me. do you have any idea what it might be

[@jeffmee763]

Got the same problem it looks like the sensors on my right side or faulty new ones of Ebay do the same. Jeff

[@young10again]

10-4 on the dealer ripping you off!👍👍👍👍

[@TheLusaso]

"I'm doing post film editing because the other shots did not come out clearly" the video inside was still blurry as all get-out lmao 😂 jk but seriously thank you this video is pretty helpful and I have a Chevy not a Ford

[@sydneypendergrass4645]

Have 2004 f150. Went through and can hear all 4 sensors clicking. Any other suggestion? Great info in the video

[@dianeblomker9139]

2002 ford Explorer limited. only 1 didn't work before. but I had my mechanic replace all 4 cause it takes 1 hour to take the whole bumper off. started beeping fast even tho nothing behind me shortly after u replaced them. now none of them are working?? any ideas where to go next?? all 4 can't quit at one time can they. that's why wondering if a fuse or wiring I need to have him check. we watched your video

[@rickdff62]

Mine just went out and found this. Thanks so much!

[@jasonvandervalk3679]

Every vehicle ive ever driven hasn't had back up sensors! I just ues my eyes! If these sensors are covered in dirt do they still work?

[@faroukboucherit6006]

Thank you so much sir ! , I just fixed my backup sensors

[@Shane23Armada]

What was the issue. My 2013 armada back up sensor keep beeping constant any idea ?

[@troycruikshank1027]

Thanks for the sweet video. It totally helped me out

[@hildakv2009]

I have recently started experiencing this problem. I so t have a wand but I was able to hear a ticking sound on all the sensors. Since u said towards the end of the video that u identified about 3 bad sensors but with the here he wand u only heard one wrong...could this mean that there could still be a problem with the sensors on my truck? What other problems could it be

[@TheKingOfHalo]

I'm trying to install this system on my 2000 explorer. I have the bumper with sensors and I plugged it in to the stock connector. I also plugged in the parking button and rear module. All the wiring was already in the truck so it was plug and play. But the switch light is always on "off". The only thing I couldn't find was the speaker for the backup noise. I'm guessing that's what's causing the system to stay off, since the speaker isn't plugged in. I can't find anything on the RSS speaker for a second generation explorer though :/

[@alaanoureddine3759]

I replaced all 4 sensors on my Ford f350 2006 but still the parking beep is not working and the parking off light is still showing.any suggestions please?

[@MrGrerm]

In the uk we call them "the main steelers"

[@briandowdall6495]

I installed new sensor but no dice. How do I test the wiring from the harness to the sensor?

[@danieloldag7624]

What if I can still hear all 4 clicking? 2003 ford excursion. Parking assist light still on.

[@kathleensepar1665]

On a 2007 STS where is the diagnostic unit. Under the seat or in the trunk?

[@dopedickinsonbb8359]

Do one of these sensors make the engine light come on??? Cuz mine were working then not an now my engine light cut on at same time

[@TheOGRobertCarrasco]

Thank you for posting this!

[@texanbalaban6777]

No special equipment needed; pulls out inductince wand haha

[@DeathScouter]

I guess you missed the part where I said I was using it for the benefit of the camera/microphone... but thanks for watching. :)

[@texanbalaban6777]

@@DeathScouter i gotchu B0$$, put my ear to mine and none of the 4 were clicking, gonna replace all 4 and move to next diagnostic step. Good Video, thanks for postin 😀

[@uasea13]

Hi I have a diesel engine, so I can not leave the key turned to check the sensors. Any ideas how I can check if sensors are ok? Thanks.

[@tylercovell8440]

No special equipment...... oh just an inductance wand 😂

[@joec2420]

He said in the video at least twice that the inductance wand was just to amplify the sound so the camera microphone would pick it up.

[@matthewbittenbender9191]

On mine I can hear the ticking very faintly but the ticks are half as fast. The far right one is barely making anything. The sensors are clean but not operating consistently.

[@presidantscrooge3769]

Have a 98 Chevy suburban was beeping in reverse it stopped but senors not on bumper could they be in reverse lights I can't find them

[@westcoasttanker]

Good video thanks for that.How about the sensors by the spare tire. Did you have to lower your spare or could you reach in there?

[@DeathScouter]

Everything was within reach. Thanks for watching.

[@ralph9987]

I love that inductance wand! Do you have a link to where I can get one. Didnt find anything o my usual supplier webpages :(

[@owenlewis8166]

This is typical tool that telecom techs use you can find them on Amazon search fro telecom toner

[@elmeradams8781]

What else can they diagnose?

[@naffael]

Where is the link to find this sensor. All the ones I see are hard wired and small a round piece not an "L" type bracket for my Ford. Please help.

[@dudleydorite7678]

I can't get my sensor button on dash to light up. wondering if sensors would case this

[@290wayne]

Thanks for the help.... I ordered them from EBAY! The only problem it took 3 weeks to get them from CHINA! I took one apart.... had SALT inside that destroyed them....

[@OGSumoVIBE]

This video saved me $$$! Exact scenario you described here. Hey quick question. I had the little plastic mud flap piece hanging below my front bumper of my Ford Excursion damaged, and now it fall off. Any idea what that part is called and where I can find another one? I don't know what it is so I can't search for it obviously.

[@DeathScouter]

LOVE good feedback. Thanks for watching. If you are talking about that piece of plastic that runs all along the underside of the bumper, its called a "valance" or a "spoiler". Not sure what year you have but did a quick search and found this for you. Price from $17 up to $85 www.carid.com/2005-ford-excursion-bumpers/

[@xxxmikeyjock]

replaced the sensors on 2005. still no go.going to have to check the speaker and module next

[@mcampbell6755]

system beeping when backing up but interior camera is flipping out......keeps rolling fast and doesnt stop............any suggestions ? 2012 escape. thanks

[@lakika76]

Hey, thanks for video, can you send me link or name of replacement sensors that you recommend. The ones in Amazon have mixed reviews, and ebay has a lot of different sellers/options, I'm afraid to buy something that might not work well. Thanks!

[@mikehernandez8454]

pls help my ford f 150 2914 has a backup camera but the plug in the back of tail gate came unpluged were do i plug it back to

[@Deerector]

I heard clicking on all the ones your put by the wand... I don't get it ????

[@cindiecornelius6840]

replaced one bad sensor. also replaced the switch, put it in reverse and the switch still turns off.. What else can I do?

[@adolfohurb]

I have a buick whit factory sensors but I want to change the factory stereo and if I do that I loose the beep the ligth works but the beep goes to the stereo and then to the front driver speaker and I don`t know how can a chanse the stereo whit out loosing the beep

[@tonyc4981]

ITS ALIVE!!!!!!!!

[@geoffclewley989]

My parking aid bleeps continually (intermittent). Rover 75 2004. At other times it works perfectly, and once saved a small child's life. Is it possible to change a sensor without removing the bumper?

[@DeathScouter]

Geoff, I have to confess I'm not experienced on the Rover, so I don't know what it takes to access your backup sensors. All the systems are fundamentally the same, being that if you have any defects, troubleshooting starts with suspecting the sensors. Sorry that I'm not answering the question you asked.

[@kevon9849]

Could my sensors be too close to one another??

[@bobcottone9674]

I have a Mercury Sable (2008). When I checked on eBay for the part number (4G1Z-15K859-AAA) the cheapest I could find was $175 for 1 sensor. Is there a better deal available? For that kind of money I'd rather install a backup camera.

[@DeathScouter]

You can find brand new ones (set of 4) for $124 (www.paintedoemparts.com/store/p1688/Painted_Parking_Sensor_System.html?gclid=CM6VpNrV99ICFZaPswodrcYFog). Individual ones are same price (wow!) on ebay and Rock Auto. There is an ebay auction right now for used ones @ $85/each. Otherwise, you can try calling around to junk yards and seeing if they have them. Not sure why, but your make/model is pretty expensive.

[@MrSmakboy]

Thanks for the video, this describes the problem with my 2004 Ford Freestar exactly. I don't have one of those audio testers and I cant hear anythings from any of the sensors. Is there another easy way to test them? In the end I might just buy 4 and swap them all ; )

[@DeathScouter]

MrSmakboy Sorry for the delay in responding but I hope you got your sensors fixed. Did you swap them all? I don't have an alternative method if you can't hear the ticking. Mine happen to be loud enough that you can hear them with the naked ear. If you know someone who does telephone work (that where I had my wand from) they will have an inductance wand you can use. I don't know what else to offer you. Sorry.

[@montu492]

Thanks for the reply. Whenever I put the reverse gear the left side sensors continuously make ticking sound as if something is placed very close to them. I have checked it a billion times and nothing is there for miles behind the sensors but still they make that sound continuously. Please help.

[@DeathScouter]

If there is something happening on "one side", then you could try moving the right side sensors to the left, and left to right, and see if the problem follows the sensors or stays. Virtually all backup sensor issues are due to 1/more sensors going bad, so we may do this work without actually fixing something. Would be nice if you had anyone with a similar truck, you could swap sensors as a troubleshooting step, otherwise, you may need to buy a couple and rotate them through until you find the 1 that's broken.

[@naffael]

does anyone have a link to where I can buy the sensors? i just can't find any for my 2006 Ford F-150 pickup. Thanks

[@dianeblomker9139]

Bought 4 new sensors on Ebay - replaced them on my Ford Explorer. After 1 day not working. All four not working. Is there a fuse that is related to the sensors or what else can I check

[@DeathScouter]

+Diane Blomker Did they work for that 1 day? If so, your problem is definitely with the sensor(s) and not any other components. If it worked after changing them all out, you may have had a new sensor blow after the 1st day, which would take the system offline again. If swapping them all out NEVER fixed the problem then let me know what year your Explorer is and I'll try to look up which fuse is for your sensors. If it's not the fuse or the sensors, I would take a look at the wiring or locate the control board.

[@MrJackmelling]

what if no senser is clicking ?

[@allentraylor5659]

i don't have a "wand" either. I am wondering if i can just disconnect them one-by-one to see which one clears the fault ...OR.... are they wired in "series" and will not work with one removed (like xmas-tree lights) ??

[@DeathScouter]

Allen Traylor If you get your ear close, you can hear the ticking and you don't need the inductance wand. I used that simply to amplify the ticking so the camera picked it up. All 4 sensors work in series which is why 1 bad one takes the entire system offline. For $30-$40 bucks, it might be worth the time savings to buy all new ones and be done with it. If that fixes the problem and curiosity starts getting the better of you, then you can spend some time swapping them out 1 at a time to find out which ones are defective and you may end up with a spare or 2. It all depends on what your time is worth to you.

[@allentraylor5659]

Good points.. My 2006 Chrysler 300c is a bit mor complicated with and L.C.D . indicator display, just ONE of those sensors cost me $40.00 , it was intermittent but now its like its shorted out, I'm assuming the issue is the same...I'll give this all a try.... Thank you

[@leroyhelton7011]

I checked all the sensors and they were all ticking but still they are not working. Any suggestions? I tried the relay switch also but that didn't help either.

[@DeathScouter]

I'm still going to bet on 1 of the sensors being broken. You can get a 4 pack from ebay pretty cheap so I'd swap 2 at a time to find out which one(s) is bad and then end up with a couple of spares.

[@onsbymiles4516]

How much did you pay for inductive amplifier probe?

[@DeathScouter]

I bought this one years ago for $40. I just checked online and Amazon has them for $55

[@danmadigan6930]

I only could hear 1 sensor clicking, bought 4 off ebay. 1 was bad out of the box so put old one that was clicking in. Now all 4 click but parking light button still lit. If i press it light goes off for less tha 1 second. Is this a switch or module problem. Thanks for the troubleshooting hints

[@DeathScouter]

Sensors are the most common problem. If you swapped the sensors and the system is still "off", then I'd suspect the control module. I've never swapped one, so I can't tell you where to find it. Sorry.

[@danmadigan6930]

I pulled code today shows short between sensors and pam. Ugh have to start tracing wires

[@DeathScouter]

UGH... start with the areas where physical damage could occur. Start with the sensors and work your way back. At some point it will get difficult because the wires will get bundled/taped together and feed into the overall wiring harness running up to the computer. GOOD LUCK.

[@danmadigan6930]

Traced to speaker on PAM module and was bad put temp speaker in and it works. Will get Ford speaker for $20 on ebay. What a pain but fixed. Thanks for the information and help

[@markatkinson6236]

if the video was in focus it would help...

[@DeathScouter]

Message received. The camera auto-focuses and sucks up close. I've now switched over to the HERO 8 so my new videos will be crystal clear. I appreciate the feedback.

[@sipapito]

They all tick ok have continues beep when put on reversed than stop. Help!

[@elmeradams8781]

They could be dirty

[@TidalWaveDan]

Hey, 8 years later, how’d those “cheap eBay” sensors hold up? I’m asking because too many people say, “stop being cheap”, “Buy OEM”, “cheap Chinese crap”, and all kinds of dumb shit. Wanna know how those sensor held up.

[@barryhallsted]

Focus?

[@montu492]

What if the sensor makes the ticking sound even when there's nothing infront of it?

[@DeathScouter]

Ticking is normal... does it "tick differently" when you cover it?

[@peshewa0529]

I replaced all of mine and they do not work ! So whats the problem ? I have a 2007 F250 Super Duty.

[@hamiltonfamily69]

peshewa0529 I have the same problem. I have never found an answer.

[@kennyg.4329]

I don't know if you'll get this or not but if you look in some of the ford forums they'll tell you some trucks had a little speaker independent of the audio system that went bad. I'm gonna bite the bullet and get the ford dealer to plug in and run a scan on the system because all of mine aren't working

[@jeffmee763]

Look for the control box if you follow the wires you will find the box it's normally the problem.

[@MercedesE63S-AMG]

What if all 4 are clicking but it still says off on the control? Then what?

[@sammygarcia5909]

Did you figure it out cose I have the same problem 😕

[@MercedesE63S-AMG]

@@sammygarcia5909 I haven't done anything further with it but it's either the speaker or the device itself. Either way I believe on the Explorer they are one piece anyways. On excursions & etc I think they are separate so you can replace the speaker or whatever the main device is called.

[@COOful3]

Replaced all 4 on my dodge...still a problem

[@newcoyote]

Ugh! I hate it when I see "Problems with ABC systems are almost always caused by XYZ". Whenever I try to diagnose something, it always Always ALWAYS turns out to be some weird rare flaw and never the "most common" anything. Every. God. Damn.Time.

[@DeathScouter]

I feel for you. I just spent more than a thousand with a dealer who couldn't figure out my soft brake pedal on a different vehicle. "Most of the time... its the master cylinder" Well, not this time, and then not the vacuum assist, and then not the ABS module....

[@blankreg1525]

HAHA- MY DEALERSHIP WANTED $251 JUST FOR A SINGLE SENSOR!! I ordered a 4-pack of eBay for 25 bucks.

[@DeathScouter]

Yup... same experience I had. Sad isn't it? No need for dealers to screw us so badly....

[@BARFYADAMS]

I'm replacing my bumper but want to reuse my old backup sensors. Does anyone know if it's possible to remove and reuse the backup sensor bumper mount holder?

[@DeathScouter]

+BARFYADAMS That will likely change per vehicle. I know on my Jeep Commander, the sensor holders are glued to the (plastic) bumper skirt, so they are incorporated into the bumper design and not detachable. I would suspect that (as with my Ford truck) a plastic holder that is in a steel bumper is probably able to be removed and reused.

[@BARFYADAMS]

+DeathScouter It's a 2006 F150 Lariat. The bumper is the same as the one in your video.

[@DeathScouter]

Just a follow-up on my "ebay special" backup sensors. Since making this video, I just had 1 of my sensors fail and need to be replaced again. I'm not sure how the quality of my "ebay specials" compare to OEM since I bought the truck used, but the ebay price is STILL $35 for 4 new sensors, so I found and replaced the bad sensor and now have 3 spares.

[@DeathScouter]

BARFYADAMS We've had constant rain here (Baltimore) so I didn't spend a lot of time under the bumper looking to how to reuse the mounting holes. As soon as it dries up a little, I'll get back under the truck and see if I can figure out how to remove the mounts.

[@BARFYADAMS]

+DeathScouter ok thank you

[@lutherjohnson1423]

Anyone know how I can disable this system from my truck? I have a plow on it and it gets really old to listen too

[@DeathScouter]

As you can see, there was an "off" button to turn it off for the times when you have a trailer or other reason why the sensors wouldn't be needed. I'm not sure if your vehicle is the same.

[@lutherjohnson1423]

@@DeathScouter yes my truck is the same, however I'm looking just to unhook it permanently. I've normally got a trailer on it and it gets annoying turning it off every time

[@zombieallen]

Anybody have any idea if bad sensors would cause the system to act like something is behind me when nothing is? I can't seem to find anyone else who has this problem.

[@DeathScouter]

+Allen Reed Typically they die, but I don't see why a bad sensor wouldn't do what you're describing.

[@beanybain]

did a new sensor fix your beeping . I have same proplem

[@zombieallen]

Yes it did, actually.

[@beanybain]

+Allen Reed thanks big help

[@gregalbert3895]

my back up sensor goes off when nothing behind in reverse ??

[@pnwoverland253]

Greg Albert is your tailgate down?

[@gregalbert3895]

Forget tailgate. My backup sensors don't come on as soon used too.It seems to get me much closer.

[@andysmoore]

Think I need glasses.

[@the1spyderryder]

Camera stayed focused on table top

[@binkalink420]

Wow, I couldn't bare watching that whole video.

[@bryanbryan7080]

jesus! learn how to focus.

[@billbill8355]

talk toooo much mot vlear on wire harness

[@larsschroter6994]

focus you fack

[@dave-3187]

if you're going to do videos you need to get yourself a decent camera

[@DeathScouter]

I appreciate that. Thanks for the comment. I do the best I can with the best I've got.