Troubleshooting Twin Cylinder Air Compressor of Caterpillar 950B || Replacing Broken Crankshaft

[@МаксимКороль-э3е]

Я уже запереживал, что разборка-сборка не на песке сидя на корточках. Ан нет все в порядке - промыл узел водой, не просушил как следует и собрал на старых деталях.

[@ambibox9734]

однозначно

[@murziks1]

- ну так завтра сново приедет.

[@Romaded]

Здравствуйте,вам не всё показывают, они не глупее нас и конкуренция там дикая,как правило таких мастерских по улице с десяток- два и если плохо сделать то к тебе попросту не приедут,,,,, удачи

[@igormaevski7769]

у них ещё и верстак с тисками есть!

[@murziks1]

@@igormaevski7769 -- вау !

[@jackking5567]

Good god I'm not surprised that crank was broken! Dry bearings, hammering them in randomly with a home made spanner, lack of assembly lube on half the friction surfaces, dirt and gravel ingress from the bench, the list is endless. You'd think the workers were doing it on purpose to get more work..

[@Chazaxl]

No torque wrench in sight. I commend their effort with what they have but agreed.

[@asbestosfiber]

Yes I am sure they should wait until the snap on truck comes and buy a full set of tools.

[@asbestosfiber]

@@Sailor_Tom I didn't even say that. Lol yourself

[@mecamaster]

What do you mean no assembly lube, didn't you see the 2L pop bottle?

[@dochonni1586]

They give 3 days waranty! So everything is fine! 🤣

[@СОНЯКОШ-ж8д]

Я думал он будет верен традициям и заварит колено сваркой, а он взял и новое поставил - это жульничество чистой воды! Ну хоть подшипники кувалдой выбил и их же назад так же заколотил )))

[@КонрадКарлович-й2щ]

Читерит.в бан его!)))

[@PIMEX01]

он даже смазал колено и поршни перед сборкой-не по фен шую

[@billadmond9450]

I'm surprised that for a major repair where they replaced the crankshaft they didn't replace the bearings??

[@dtiydr]

Why? The seem to rotate thus they are perfectly fine, 20 years old doesn't matter with hardly any oil they will just work fine no need to change.....

[@billadmond9450]

@@dtiydr They seem to rotate??? LOL are you a mechanic or a nails polisher LOL

[@dtiydr]

@@billadmond9450 You obviously didn't get the joke. ;)

[@johnwilliams-sc1vf]

you cant beat precision engineering carried out in pristine working conditions !

[@johndonahue1935]

Precision bearing beating!

[@rowdog6376]

And no Milwaukee power tools in sight😆

[@WCKD.]

​@@johndonahue1935 In some vid, they installed transmission input shaft bearing using sledgehammer. They just hammered it in. :'D

[@Spookieham]

Distinct lack of lubrication in those bearings

[@SuperMechanic]

Amazing work very nice 👍

[@rosanapascoal7747]

Very good. Como admiro voces. Pela sua capacidade com pouco recurso digo questao de maquinário. Vocês sao bons mesmo.sao serios profissionais. Homens de honra. Parabéns gostei demais desse video. Aguardo mais videos seus. E bom demais ver seu trabalho ..eu amo mecânica mas pra mulher e meio complicado mas amo. Meu pai tinha oficina mas foi trabalhar com caminhão e acidentou e morreu. Dai acabou toda alegria da minha vida..abraços do Brazil.

[@Ternchannels]

very nice good job ❤️❤️🙏

[@diennuoc824]

Chào bạn .Hoàng rất là ngưởng mộ bạn.Kiến thức, tay nghề cùng với cách diển đạt của bạn thật hay.Cãm ơn bạn đã chia sẻ cho mọi người ..

[@MegaJohnhammond]

Discovery channel should have a new show for shit like this, "How It's Destroyed"

[@jackking5567]

Haha nice one!

[@mecamaster]

This is a pretty dumb question, But what sorta clothes is the mechanic wearing? that sorta hard wearing but lose/baggy stuff?

[@relaxingl25]

Вау!Новое видео,всегда стараюсь смотреть в числе первых!!!

[@rinji_ff8587]

капец на старые вкладыши собрал которые уже в хлам убитые

[@igorrudevets6463]

Да и подшипники, которые туда-сюда без тени стеснения молотком погоняли, тоже зря оставили

[@Евгенийевгений-т5д]

@@igorrudevets6463 до этого же работали)) и сейчас будут работать)

[@davidheidbrink1135]

Washing ball bearings with water, good God ,not on my watch !

[@wolfparty4234]

Bro, you gotta remember, these guys have been doing this kind of work since the crusades in the dirt!!! 🤣🤣🤦🏻‍♂️

[@wolfparty4234]

That’s holy water btw🤣

[@MudOilnGears]

As long as they’re dried and lubricated afterwards, bearings don’t care what you wash them with.

[@КонрадКарлович-й2щ]

@@wolfparty4234 спирт

[@asbestosfiber]

these dudes could fix shit you could only replace

[@NikitaPrikazchikov]

запрессовка подшипников на высоте. главное что перед этим под водой промыли! бомба. Еще сто лес проработает (сарказм). Ах какой же динамометрический ключ отличный. на скрипе работает.

[@doutordelmar]

Parabéns para todas vocês, pelo trabalho espero que tenham um bom salário, !

[@eddiereichel9354]

Its funny the guy running the camera makes more than the guys actually fixing something.

[@evgeniy007]

Ну вы чё старые подшипники и вкладыши поставили , неужели так дорого заменить ?

[@Евгенийевгений-т5д]

на катерпилар да))) месяц бесплатно работать если не год) если оригинальные канеш)) а вал явно по соседству взяли)

[@Kathir-gy1gm]

Super ❤❤❤❤ good

[@rania.s3906]

From indonesia, terimakasih?

[@kotleta4634]

Помыл бензином, помыл водой .... убогость во всей её красе ))

[@carbonarrow7]

Washing the solvent or gas right into the river.

[@aj9270]

🤣🤣 washing bearings with water AND not even bothering to dry the parts off i bet that lasted 5 minutes

[@alextakoj1807]

Так вот где делают колодки для болидов в формуле1!!! 🤣🤪

[@fredpierce9363]

They probably didn't want to ruin new bearings by hammering them in, so they just ruined the old bearings instead. Half of the world runs on crap like that.

[@edsonjanosmartinezchavez3846]

Cómo se llama el dado de tres puntas para los tapones de la cabeza?

[@bonzai2380]

Do you notice the lack of ratchet wrench for sockets.

[@homerosimpson309]

first time I see working on a table and not on the floor

[@КонрадКарлович-й2щ]

Я тоже не понял.а где притирочный песок?

[@ЮрийБольшаков-ю4ю]

Куда торопится так,что из рук все летит,а торцовочная ключи сделать не может,головками мучается.

[@ellionpadilla5283]

travajan con lo que tienen pero no ponen repuestos nuevos de que sirve poner el sigueñal al conpresor sino canvio anillos

[@rexphamdom6211]

Hi I like you bro 👍👍👍

[@BigRigIron]

Думал он тапкам поршень забивать будет, а у него есть кружка

[@MechaHolic]

Great work

[@caraddict-3179]

Молотком подшипник забивает в внутреннюю обойму...🤦🏽 Варвары...

[@aj9270]

precision pipe on the allen torque wrench 🤣🤣🤣

[@Юра-к5н3с]

Мастерская очень крутая ...верстак и головки с воротком

[@goodman1028]

А где маски? Вируса уже нет ?

[@ДавайДосвидания-м7ф]

Когда увидел, что подшипники забивает ключом - видео выключил🙈🙈🙈,а так вроде хорошо начиналось...

[@evangelorodrigues5005]

Nice 👍👌🚿

[@TShawn-g7c]

My nick name would be 6 TOEs. If i worked in flip flops. I almost lost a few toes and i was wearing steel toe boots.

[@MrMercurymark]

Top top! Muito bom 👍🏼

[@blocknyckeln]

those poor bearings they wont last so long,first he hammers them off by hitting the outer ballring well rip new shaft, you can se from the bigend bearing caps that it has been dismantled a few times that compressor.

[@mixdiver12]

Only work table in Pakistan! they have to share -)

[@telebos]

Вот так эти специалисты и аппаратуру ремонтируют, все на коленке. Вид только придают и толкают обманывая.

[@WolfgangS]

They work on a bench, not in the dirt !!

[@DEMON23027]

ну тут всё как всегда,.все бы только водой и мыли.

[@offside3737]

Air compressor for caterpillar 3306 but no repair kit no bearing kit no orders spare part the dealer CAT

[@shahrizzashah1391]

Jahanam bearing woi basuh dengan air,minyak pwn x buh..

[@bonzai2380]

Oh my god, would you please stop beating ball bearing on and off with a hammer. IT DESTROYS THEM! It reduces the bearing life by a large margin. It puts ball indentation in the races so the bearing pounds when rotating causing spalling in a short time, which is pretty much the end of the bearing. You can tell a bearing that have been hammered on right away by the loud hum sound given off when rotating.

[@abas-rg8te]

این چه طرز بلبرنگ در آوردن است.پدر جد بلبرینگ هم به غلط کردن افتاد 😂😂😂

[@flashgarage]

Кто нибудь, объясните этим оленям, что прокладку не нужно мазать герметиком

[@RA6ApARA6a]

Рекомендую отправится туда и показать как надо

[@andrewmena3118]

Whats that NOISE??? do you think its the bearings???? NOPE JUST PRETEND YOU HEAR NOTHING!!!!!!! 🤣😂🤣😂🤣😂

[@WonderfulSkills]

nice work

[@RfsdsgEsfdfg]

фигня кака то, я думал он щас с пола гаек наберёт и вал на сковородке новый сварит

[@سيدسيد-ص3م4ب]

Cool work sir thank you very much 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏

[@muhammedbahij5483]

Who heard ya lili ya lila song in the background hhhh

[@padigaluraceh9157]

Verry good

[@scheidldratza3001]

torque wrench is bullshit. I like how they put in the baerings. Nobody in Germany repairs such things. We are all environmentalists and safe our country. Throw your broken things away and buy new. That´s the real bullshit. Good luck to the workers all over Pakistan. And there is no woman, knowing everything better.

[@josegoncalvesjose9999]

❤

[@letcikigor]

👍

[@ankamanka9867]

👍👍👍👍👍👍👍👍👍

[@воланддемоор]

ох и халтура. вкладиши нахер новые ставить? итак сойдет

[@Tomor88]

Dynamometer in hand ;-)

[@ankamanka9867]

👍👍👍👍👍👍👍👍

[@peteradams8855]

Well done tip the oil down the drain you bunch of cow boys I wouldn’t let you make the tea let alone fix an engine

[@bandalantonio6694]

편집좀해서올려라 물로씻으면 환경오염인데.. 에효 유투브 돈발려고만애쓰지말고

[@fasullodavvero]

Pessimo video di pessimi "meccanici"...😱🥶🤢

[@asbestosfiber]

All the big ass babies. "they don't have this tool or that tool" "they are doing it wrong" These guys fix stuff you would just replace with a new part, these trucks go out on roads that make a goat path look like a super highway. they are getting it done. You all can sit back in your garage with your $8000 cabinets and 30k worth of tools.

[@hats-k2z]

it doesnt cost more money to do the job right

[@ar.n5695]

👎👎👎

[@re-fix9678]

Very good

[@ankamanka9867]

👍👍👍👍👍👍👍👍👍

[@carbastan1461]

👍👍👍👍👍

[@ankamanka9867]

👍👍👍👍👍👍

[@carbastan1461]

👍👍👍👍👍