How to Replace Water Pump 11-17 Chrysler 200

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@RuralTowner]

Neighbor has one of these cars & has started having overheating issues & losing coolant. Had a look into the bay for him & was expecting it to potentially be a PITA if having to go in from the top. After looking up what the WP looks like it would seem "simple" & seeing this does show it being fairly easy...but tedious getting the covers out of the way to reach the pump.

[@HeinzGuderian_]

You can disconnect both + & - terminals from the engine compartment. Both cables go directly from the battery to the lugs in the engine compartment.

[@mtsanchez27]

You don't need to disconnect the battery terminals to this job!

[@jonsteph8991]

Great video. Really need one on replacing the heater core.

[@ToyManFlyer1100]

Most Excellent video...And, you talked slow enuff where I can understand you....👍👍👍👏👏👏😊😊😊😊

[@teamtateamerica]

This is harder than it looks, I'm working on one now

[@fallenone6]

Great video very helpful, do i have to remove the dial pins inside the block with the water pump or do i just leave them on the block?

[@metropcs7250]

Why did you disconnect the battery? Nothing you can short where the pump is located.

[@alfym1094]

I didn't see when you tightened up the bolts for the water pump pulley

[@metropcs7250]

Torque for the pulley is "good and tight".

[@Evil12monks]

May I ask is this the 2.4 L. Motor or the 3.6 L. ?

[@MrEklessiast]

That’s 2.4L

[@bobbigwood7823]

Great video what engine is it?

[@brucemeskill5129]

My car is overheating and I'm not getting any codes I have removed the thermostat housing from the engine block There are now four open ports on the block. I believe two of them are coolant intake and discharge for the heater core and the other two are intake and discharge to the radiator. When I start the car there is no coolant from any of the ports being discharged Does that indicate a bad water pump

[@ToyManFlyer1100]

Sounds like a bad waterpump to me....

[@djsi38t]

No...the pump can not create pressure with the housing removed.

[@deathscreton]

Would it be possible to see this on the 3.6L Pentastar?

[@TRQ]

+deathscreton We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-TRQ

[@CharlotteJackson-bh1ui]

My car is overheating he said I need a new water pump so do that mean that I have to change the timing belt with the water pump to

[@richsmith9063]

Very helpful !!! Thanks. Did you Torque the water pump pulley bolts ?

[@davidrust7686]

Is this the same procedure on a 2013 Dodge Dart 2.0

[@TRQ]

+David Rust The part in this video fits your application, and the install should be the same or similar. Buy this part on 1AAuto.com: 1aau.to/m/Shop-TRQ

[@Templar-jj3ig]

That was probably the hardest way of getting to the battery I have ever seen.

[@ahmedshendi3941]

Who reset electronic throttle hyundai accent 2014

[@djsi38t]

And the only way to get to the battery.To disconnect just do it from under the hood....no need to access the battery itself.Actually no need to disconnect the battery at all when doing this.

[@ryoung6730]

This isnt for the 3.6 pentastar, only the 4 cylinder, the 3.6 a is vastly different setup.

[@danielmoore1668]

Why didnt you change the housing that is on the block also i had to change that and the pump it is such a sob

[@chaselemay9923]

You have the wrong year car buddy

[@jasonsdodd]

No way i'm letting my buddy do this to my car.