How to Replace Spark Plugs 2013-19 Ford Police Interceptor Utility

Buy Now!
New Spark Plug Set from 1AAuto.com 1aau.to/ia/MCET...
Spark is one of the four required components for an internal combustion engine to run. If your spark plugs are failing, worn, or dirty, you may experience rough starts, rough idle, poor performance, or poor mileage. This video shows you how to install new spark plugs on your 2013-19 Ford Police Interceptor Utility.
• Check here for more videos on the 2013-19 Ford Police Interceptor Utility: • Ford Police Intercepto...
This process should be similar on the following vehicles:
2013 Ford Police Interceptor Utility
2014 Ford Police Interceptor Utility
2015 Ford Police Interceptor Utility
2016 Ford Police Interceptor Utility
2017 Ford Police Interceptor Utility
2018 Ford Police Interceptor Utility
2019 Ford Police Interceptor Utility
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• 8mm Socket 1aau.to/oa/1AXA...
• Air Blow Gun
• Air Compressor
• Torque Angle Gauge
• Hose Clamp Pliers 1aau.to/oa/1AXA...
• Needle nose pliers 1aau.to/oa/1AXA...
• Needle nose pliers 1aau.to/oa/1AXA...
• 5/8 Inch Spark Plug Socket
• Ratchet 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Cloth Rags 1aau.to/oa/1AXS...
• Dielectric Grease
• Pick 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Ford Police Interceptor Utility: • Ford Police Intercepto...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@mindmythfilms1428]

My manifold is stuck... i loosen all of them bolts but the right side is stuck...

[@StonyAWACS8492]

@@mindmythfilms1428 there is a support bolt for the intake under the throttle body, its 8mm

[@lanceanglin]

Much appreciated video. Very thorough and informative.

[@NG-fj7bb]

Are there any other parts that I should/can replace while the intake is out? For example, is the cylinder head temperature (CHT) sensor under the intake? Thanks for a useful video.

[@MrRockydee07]

Should we clean the dirty engine off first before starting the job ?

[@alanstowing1]

I have a 2016 Ford Interceptor Utility Ecoboost 3.5 Twin Turbo AWD... *Former Georgia State Patrol Unit... My Engine does not have this high up in the way Plastic Plenum (Headache). My intake is low and all metal. Do not have to remove it to get to coil packs and plugs. Just loosen intercooler piping that runs to rear held down with 1 10mm bolt and remove a few hose clamps etc., Still have to be careful with rear side of engine wiring harness and clips/lines. But seems to not be that hard to do for any mechanically inclined individual.

[@dakotasaliga1817]

Is there a gasket for the plenum?

[@kinnersean]

What extra deep socket is being utilized in this video?

[@PaulMcLove]

Super‼️ 👍😉😀

[@TRQ]

+Paul McLove TV Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@StaceyLamb-e1j]

Where is the number sixplug

[@angelo_giachetti]

They dont say what vehicle theyr working on. A Chevy? Ford Taurus? Or is 'Police Interceptor' a company I havnt heard of?