How to Replace Front Wheel Bearing 2006-2011 Chevrolet HHR

Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com 1aau.to/ia/1ASHF00135
This video shows you how to install a new wheel bearing on your 2006-2011 Chevrolet HHR. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2006 Chevrolet HHR
2007 Chevrolet HHR
2008 Chevrolet HHR
2009 Chevrolet HHR
2010 Chevrolet HHR
2011 Chevrolet HHR
Tools you will need:
• Pry Bar 1aau.to/od/1AXAA00020
• 14mm Socket 1aau.to/of/1AXAA00015
• 15mm Socket 1aau.to/of/1AXAA00015
• 19mm Socket 1aau.to/oe/1AXAA00043
• 30mm Socket
• Trim Tool Set 1aau.to/of/1AXXX00004
• 1/2 Inch Air Impact Gun 1aau.to/oe/1AXAA00252
• 3/8 Inch Air Impact Gun
• Swivel
• Torque Wrench 1aau.to/og/1AXAA00044
• Anti-Seize Grease
• Brake Parts Cleaner
• Large Hammer 1aau.to/oc/1AXAA00091
• Wire Brush 1aau.to/ob/1AXAA00079
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@glenjenkins21]

I’m doing this to my HHR right now. I just wanted to see what the process looks like. Thanks for the video.

[@flint303]

Way more easy than I was thinking. Thank you for this. 🔧

[@jeep0312]

I like how everything was already passed the torque spec 😂 I’m over here like yeah I’ll be sure to torque it all to spec 😉

[@crookcounty1978]

Just take the calipers off with the bracket... one less step

[@Nancy-xg9nc]

Great video! Now all I need is a lift...😁

[@ericfischer2640]

It could be done on the ground off Jack Stands....

[@Blakethegoat]

Thanks for the videos… I guarantee I won’t get it done with zero f bombs like you but hey I’ll get it done 😂

[@marshajohnson1710]

Thank you so much for this video

[@pinzguy4937]

Great instructions!

[@Court420]

Very helpful thank you

[@MrJackson66]

A slide hammer and a wheel hub attachment will pull the old bearings out much easier than a normal hammer...

[@user-dn4uv2bb9o]

Great job

[@vnesssblk1]

I'm having problems with my 2007 HHR LT (2.2) front-end... The Steering shakes and rattles in the Steering column (driver side) Can you explain what is causing this? I also need new ties and haven't had a front in alignment since 2019. 🫤It's costly and sometimes depressing going to the dealer... To find out there's tons more to straight shoot any problems)... SometimesI feel is all about making more... ijs..Mo' money and repair(s)☹️. A garage replaced my catalyst Converter with a pipe job🤬 Ran Loud!. I stopped going to them. Please advise.

[@thehorrorsociety]

I'm going to buy the tools to do this project. I don't own a impact wrench. Do you think this job can be done with electric or should I go pneumatic? I'll probably buy used in either case. Air tools and a compressor seem less expensive in my area than cordless. I'm honestly good going either way. Any suggestions on which way I should go? (either way, even buying high end tools new is still a lot cheaper than having this done at a shop).

[@tetris3289]

Need to invest in new calipers jesus that rust

[@Cmpateb]

I was going to try looks like a headache 😩

[@Blakethegoat]

Not too bad

[@waynemonmanning4550]

Good 👍 video