How to Replace Rack & Pinion Assembly 2003-2007 Honda Accord

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/242/a...
This video shows you how to install a new rack & pinion assembly from TRQ on your 2003-2007 Honda Accord. The rack and pinion assembly transforms the turning motion of your steering wheel to the push and pull motions that turn the front wheels of your vehicle, as well as adding the power assistance. If the steering rack on your vehicle is leaking, or damaged in some way, you might need to replace it entirely.
This repair was done on a 2006 Honda Accord EX 2.4L Sedan 4-Door FWD Automatic and the process should be similar on the following vehicles:
2003 Honda Accord
2004 Honda Accord
2005 Honda Accord
2006 Honda Accord
2007 Honda Accord
Tools you will need:
• 17mm Wrench 1aau.to/o2x/1AX...
• 19mm Wrench 1aau.to/o2x/1AX...
• 10mm Socket 1aau.to/obk4/1A...
• Trim Tool Set 1aau.to/oain/1A...
• Socket Extensions 1aau.to/obGt/1A...
• Torque Wrench 1aau.to/oaN6/1A...
• Gloves 1aau.to/oaqj/1A...
• Painter's Tape
• Power Steering Fluid
• Safety Glasses
• Floor Jack 1aau.to/oade/1A...
• Funnel
• Jack Stands 1aau.to/oZQ/1AX...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Honda Accord 2003-2007 7th Gen: • Honda Accord 2003-2007...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@redrider5628]

Thanks. So far process worked great. Great video. I’m sure it was difficult to capture all the angles. Some of those areas was very hard to get to.

[@algentles5361]

HI, does the same method work for the HR drive Honda Accord?

[@UserRjt]

This the same for 3.5l v6 accord 2011?

[@MrLuvHaters]

Do you guys have a rack and pinion video for a 2014 Honda Pilot?

[@creepyscope7824]

How bout 8th gen is it the same procedure?

[@2626whwh]

Would this same procedure work on my 06 TL?

[@Lifesituations8000]

Is that the v6?

[@1chip4you]

Is this close to the same as the newer 09-10/14 accords/tsx’s with the electric power steering just without the fluid?

[@OGS_623]

Does snyone knows the exact name of the pliers used to turn the rack before installing. Last tool I nedd before seslping mines. Id greatly appreciate the help!

[@wiseguymoney]

Thank you thank you thank you, this step by step was awesome and made my life easier, and saved me about 800 dollars thx again

[@TRQ]

√ Watch the Video

[@unebonnevie]

The car model here is probably a V6 not a 4-cylinder, as V6 is more complicated. Some key notes:

[@matjoe272]

Thank you very much for showing how its done. Thumbs up.

[@hudongng]

Thank you for your v/clip, it’s useful for everyone. ❤

[@CheletoVlog]

Replacing my 2007 and the pressure lines are both 17. Also didn't need a 24 mm for removing the steering linkage. Was a 19 mm. But my new one came with those and control arms.

[@user-qx4jy3on8j]

Thank you so much for your help

[@SaidAttalah]

Amazing! Thank you for sharing.

[@christopherbrown5338]

Excellent video! Is there a way to verify if either the rack or pump is faulty?

[@jayrocksxxasap1273]

Love the work you do brother. I have a question for you... So i have a 2003 honda pilot.. Only axel that matched up was a 2002 axel... The trans side was just a little bit shorter.. But the axel that was with vins did not match.

[@sricharte89]

its all good and all, but helps if you have a lift as is makes it easier also a place to do it in, can be done on your pavement but more difficult to get underneath and do all that