Cummins m11 celect/ celect plus overhead valve adjustment.

  Рет қаралды 42,264

Trucker Style Shawn

Trucker Style Shawn

Күн бұрын

Пікірлер: 18
@staatsfiend
@staatsfiend 10 ай бұрын
I worked team 5 At JEP in 94/1995 assembly line and before I installed the valve cross-heads. I was finding an inordinate amount of misaligned half locks in the valve spring retainer. That got the engine pulled off the line til the repair was made. The pointing fingers between the head line and assembly was comical, I must have found a dozen or so over time until it was rectified that had me with TOP "good Catch" overall finds write-ups for the team I was at 40 percent and 2nd place was my friend Doug at 10 percent.....and down from there for other employee's. A friend from test showed me a disassemble engine that ate a valve and it was destroyed. Being a mechanic gave me the edge to spot problems where most others were just droids putting in they're time. so what did they do when production was lowered; they booted the temp (me), so some other got to stay on. The line was producing the L10 and the M11 engines at that time
@mrbuck5059
@mrbuck5059 3 жыл бұрын
Thank you. I'm doing a valve adjustment on a stupid old Minnesota DOT Snowplow that is all rusted up from salt.
@brodyzarate5591
@brodyzarate5591 Жыл бұрын
Hi when you are on number 3 valve is the injector rocker supposed to be loose
@yamahaMXrider125
@yamahaMXrider125 Жыл бұрын
can i remark my accessory pulley by going off of the valve position? mine is A for 1and 6 so could i do cylinder one valves closed to know that i’m at “A” and remark the pulley, i’ll replace it anyway but i figure i’ll need to clock the position regardless.
@delferdslinkey6657
@delferdslinkey6657 3 жыл бұрын
Trouble weak Jake brake on m 11 plus , need know adjusting .
@jamaluddin-b9z5c
@jamaluddin-b9z5c 10 ай бұрын
How to check compression of Cummins QSM11 engine? And what about standard compression pressure??
@donmccord
@donmccord 3 жыл бұрын
I’ve got jakes to deal with need to find the specs on that I guess before I do it
@jesusvalerio6786
@jesusvalerio6786 9 ай бұрын
Do I need to do that to replace a power steering pump base on my 350 engine
@donmccord
@donmccord 3 жыл бұрын
Mines due too need to get it done before my ecm gets back from the tuner and I put that 450hp custom tune on the poor lil motor lol
@truckerstyleshawn
@truckerstyleshawn 3 жыл бұрын
That will be nice! Hope you got a ism block stiffener
@donmccord
@donmccord 3 жыл бұрын
@@truckerstyleshawn oh yeah got it ordered yesterday
@truckerstyleshawn
@truckerstyleshawn 3 жыл бұрын
Where did you get it tuned?
@donmccord
@donmccord 3 жыл бұрын
@@truckerstyleshawn place called heavy diesel tuner in Cleveland Tn nice folks but damn expensive 1,499 for custom tune and rebuild of ecm but can’t find anyone else that will mess with m11 celect
@Son0fLib3rty
@Son0fLib3rty Жыл бұрын
Hey yall i got a 2001 cummins ISM. The oil starts out at 65 psi then drops into the teens after warming up and it drops at the filter head Ive ruled out pump, guage, leaks, injectors, jakes while everything on the valve train looks good. I had a 12 hour diagnostic that ensured the internals had normal ware. I recently had the injectors in cylinder 2 replaced as well as a rocker arm on the same cylinder replaced. I used the truck for two days and had to bring it back to the same shop. The mechanic informed me that there was a wire broken on the number 2 jake assembly. And now insists that it wasnt from the work they did but dosent know whats wrong with it please any suggestions will be greatly appreciated
@truckerstyleshawn
@truckerstyleshawn Жыл бұрын
I would pull the oil pump and shim it or Chang it out. That’s what I would do.
@adilazeem4307
@adilazeem4307 Жыл бұрын
I have qsm 11 engine knocking problem abosorve above after1500 RPM give us suggestions
@jerryjimenez4626
@jerryjimenez4626 2 жыл бұрын
Think I can get a link for that diagram and manual
@jamaicanorthcoasttrucking3854
@jamaicanorthcoasttrucking3854 8 ай бұрын
My m11 engine start run and just shut down and don't know the problem
Truck Repairs: L10/M11 Cummins STC valve and injector adjustment
11:34
Watch Wes Work
Рет қаралды 358 М.
HOW TO: CUMMINS N14 OVERHEAD SET / VALVE ADJUSTMENT
14:55
andrews_method
Рет қаралды 101 М.
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 48 МЛН
Интересно, какой он был в молодости
01:00
БЕЗУМНЫЙ СПОРТ
Рет қаралды 3,8 МЛН
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 27 МЛН
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 117 МЛН
Cummins M11 injectors - Assembling, disassembling and testing
14:52
Камминз14 регулировка форсунок!
4:52
Дмитрий Америка
Рет қаралды 30 М.
NT 855  175 kwi COMMINS. Valves and injectors adjustment
16:21
Hydraulic mechanics 777
Рет қаралды 59 М.
Cat C13 Valvetrain and Overhead installation and adjustment.
24:01
Insane turbo barrel makes 30+ psi boost on FIREWOOD
10:03
Camp Dogs
Рет қаралды 2 МЛН
Cummins N14 Valve Lash & Injector Adjustment
5:47
Flannel Philip
Рет қаралды 66 М.
Cummins M11 valve adjustment
5:56
NV CTE Diesel Technology 2
Рет қаралды 6 М.
M11 Cummins setting valves and injectors
13:32
Jake Ziegler
Рет қаралды 71 М.
Will a barrel of engine flush clean a sludgy engine?
12:54
Garage 54
Рет қаралды 1,4 МЛН
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 48 МЛН