How to replace freightliner cascadia pinion yoke seals, Front, & Rear, kenworth volvo ect

[@MrSchuu]

what silicon did you use?

[@TRUCKINGTIPSDIY]

amzn.to/3NmhUwr

[@CannibalFetusRobbery]

So glad i found your channel. I'm a new diesel mechanic and I get thrown crazy jobs like this with no knowledge on what to do. Your videos save my ass quite a bit.

[@vicpetrishak7705]

Always have a new crispy SnapOn 12 point socket on hand , not a Garbage Freight socket . In the event the 12 point bolt head strips , with a 3 pound hit the bolt head hard deforming the bolt head . Then pound the socket on the bolt head. I use Number 2 Permatex non hardening sealant on the outer metal surface of the seal . Pack the inside of the seal with grease , holds seal spring in place . Great Video ! 121/23

[@cbenson1820]

I did it myself last night and successfully replaced it. thank you very much

[@TRUCKINGTIPSDIY]

im glat it helps you, thanks for watching 👍👍👍

[@28hotrods]

From someone who does this for a living those yokes don’t come out that easy all the time even with a yoke puller.....lol

[@danieldoucet9121]

I once used a 1 inch impact with a yoke puller AND heat and got the ok to just torch it off, which I hate doing. Some people just don't put nevr seize.

[@nessperez9428]

𝑰𝒎.𝒂𝒈𝒓𝒆𝒆

[@sidneymarcosdeoliveira9232]

@@nessperez9428 p

[@johnb1121]

question on a freightliner front axle inner axle shaft bushing an seal what tools do you use??? Please Please an where s my tool box tour thanks...

[@donfichter5312]

I agree good video but those yokes can be a bear to take off never had one that easy

[@douglasfurlong1]

your videos are great...straight the the point....and very helpful, thanks so much for taking the time to do these great vids!!

[@TRUCKINGTIPSDIY]

Really appreciate it 🙏thanks for watching sir

[@winstonspratt5556]

Excellent... excellent presentation. Your videos are awesome. Thank you.

[@geoestrada5001]

This is the best video very professional and the right toolset, thanks for this great information

[@Seveneleven44]

Never saw a yoke come off that easy.

[@kellykolnes1954]

That's what I said lol .only on you tube you'll find someone get the easy one

[@jackorlando7]

I have oil leak from the same place on my Cascadia, but i realized the bearing has a free play. Can i adjust the free play somewhere behind the seal, is it adjustable???

[@jeremyashley1]

Awesome.... can you do a video on how to reseal power divider case.?

[@edgonzalez1871]

Keep it coming with the videos. Good job. Thank you..

[@TRUCKINGTIPSDIY]

thank you sir!!👍👍

[@truckin3799]

Just did mine last week, pinion nuts were crazy tight

[@supertrucker1356]

Do you suggest replacing that stabalizer bar if the bushings are a little dry rotted

[@RA-zk4gg]

You can can put a sleeve on the yoke if it have a lot of ware righ?

[@mickysmith8851]

Hope you kept the shafts in phase

[@epiphanio4430]

Thanks again brother for your videos is big help 👍🏾🇲🇽

[@TRUCKINGTIPSDIY]

You're welcome, gracias compa

[@kennethcampos1291]

I like the way you guys work, nice and cleand. Thas call perfection..

[@cristhiansandoval757]

It works with 3/4 inch gun impact Milwaukee m18?

[@d-s-ll2378]

when have locktie, use fire to heat the threads enclosing part will help release that 12 point bolts. very often people damage either socket or bolt head.

[@orlanmedina3693]

Buen video. Todos esos trailers son standard o tambien metricos? No se que set de sockets comprar

[@markmccue8472]

Good video but God help the next guy that has to take that apart . I think they use blue thread locker not red at factory.

[@dv-mitchellmcever8158]

I personally don’t recommend using sandpaper for the seal mating surfaces. When you remove material with sandpaper your relieving the mating surfaces friction fit design. It’s supposed to be a pressed fit to do its job, which is to stop leaks/prevent leaks

[@iTzNeku]

On these they reccomend sanding the seal surface to remove rust, the seals have a retaining spring that allows a minor amount of material to be taken off as long as there's no chips or large scratches (think hammering a pry bar into it) then typically the seals will fill in, most are anaerobic sealers and not just rubber as well so the mating surfaces will swell after install

[@crickwywitelessiempreandab7739]

No se te olvide revisar las niveles de aceité.

[@faircrest5860]

Good Job you're a teacher

[@4joeyfingas]

Don't know the torque specs so were just gonna send it...nice

[@TRUCKINGTIPSDIY]

What?

[@rogeliocastillo406]

Lon unico que no explica es como debe estar alineado el drive shaft. O como dicen in phase. Muy buen video

[@geoestrada5001]

Yo creo qué mientras el camión está en una superficie plana todo encaja perfectamente, y no tiene qué forzarlo, pero todo está bien entendible y adelante amigo,

[@patojo8111]

Hey 👋 Sr can give the information for the drill used on the video for the take off the big nuts on the joke thanks

[@TRUCKINGTIPSDIY]

Milwaukee M18 FUEL 1" High Torque Impact Wrench with ONE-KEY, Bare Tool Only, No Charger, No Battery a.co/d/6gQOqkp

[@LuisSanchez-ko6ul]

Es lo mismo en la de enfrente donde entra a la transmission? Gracias de antemano.

[@TRUCKINGTIPSDIY]

Si

[@adrianestrada1813]

Oiga compa una preguntita cuando lo pide que es lo que tiene que oreguntar uno como se llama exactamente el primer sello que cambio

[@mileswatkins2162]

So the socket needed for the yolk bolts are 1/2 12 point ?

[@kellykolnes1954]

Yes. Most trucks use that style . There could be different ones out there though

[@davehayes1171]

Good work bro... I Learn something and I need that same thing done on my truck

[@TRUCKINGTIPSDIY]

Thank you

[@harminderkharay8887]

Very nicely made video and nicely explained

[@johnysilver1853]

My truck has problem when I turn differential switch on I hear air does something but only one rear wheel spinning on passenger side. What can be the problem? What's need be checked or replaced?

[@TRUCKINGTIPSDIY]

Its probably just the airline fror the differential switch, put the differential switch on, go outside next to the differential and see if you can hear the air leak

[@johnysilver1853]

@@TRUCKINGTIPSDIY Thank you will try. I hope it's not internal failure

[@johnysilver1853]

@@TRUCKINGTIPSDIY I want open divider to see what is wrong. Do you know what size yoke nut socket is it usually? Also do I need replace gasket around plate?

[@indersivian1598]

Great job

[@TRUCKINGTIPSDIY]

thank you sir!!

[@utopia677]

Muy Buen tutorial gracias y saludos 👋😃

[@abenetwoldesenbet9117]

Good job bro 👏 where is your shop located???? I'm 2 times changing Seal still leaks I don't know what happened who's give me answers????

[@GurpreetSingh-sh2uo]

Can you one more video of differential main seal how can put main seal please

[@susanasolorio2297]

Bro I have a question I changed a axel differenttial yoke and everything when I started my truck it had a warning sign saying check trans... And only goes up to second gear could it be my transmission

[@kennethcampos1291]

Verry good. Brou, hi from COSTA RICA..

[@mrcaozoriz1075]

a question what given measure is the tool to remove the nut

[@shoptechnician4514]

im doing this right now because some guy drove a hundred miles with a loaded trailer on and the air bags down chewed up the seal got the bearings hot, no flakes or chunks in the fluid though i guess thats the silver lining here i dont know.

[@desmondrobin9925]

Magnificent work 👏 👌

[@TRUCKINGTIPSDIY]

Thank you sir 🙏,

[@TuneWorld57]

is there supposted to be freeplay in the drive shaft?? mines has about a 1/4 turn when the trucl is off

[@TRUCKINGTIPSDIY]

Yes little freeplay is normal

[@TuneWorld57]

@@TRUCKINGTIPSDIY is there an email i can send you a video to tell me what you think??

[@TuneWorld57]

@@TRUCKINGTIPSDIY to give you an idea if your looking at a clock mines goes from 12 to 2

[@zekers6500]

Make sure you Aline driveline because it will vibrate

[@streetglide_24c62]

What are you spraying that gasoline with?

[@makeitpay8241]

that's what i want to know too

[@envisionCamusa]

Ditto

[@tacojacker1828]

Nice 👍🏽 video man!! Keep It up!!

[@TRUCKINGTIPSDIY]

Thank you sir 🙏

[@baatarsandag5989]

where is your shop located ?

[@robertcheney6753]

Hey if you drove with the brake’s applied a little due to an air leak could that cause a seal to leak on the differential?

[@TRUCKINGTIPSDIY]

On the wheel seals?

[@lorenzorosales6243]

You have a shop out here in California?

[@smailbouadi5000]

Thank you 🙏

[@gmoering26]

What size is nut on output shaft yoke?

[@Vertikala-pc5ig]

Do you have video of steering wheel bearings replacement?

[@TRUCKINGTIPSDIY]

i will make one soon

[@glackaglack1534]

I'm dealing with the same issue.

[@TRUCKINGTIPSDIY]

hopefully this video helps you!!!

[@noniponipaa]

great video can you plz mention the corless impact gun used . i want to buy as well.thx

[@TRUCKINGTIPSDIY]

hello, i just put a link in the description, its the Milwaukee 2867 1 inch drive

[@rakape786]

Very good job, no waisted time, but I prefer a rubber hammer, why you don’t use the jaw puller kit? Is it not good for this job? I’m asking. Thank you very much. From now I’ll follow you and subscribe to your channel.

[@nolimittransport7601]

They have change that seal three times now and still leaking a lot . any suggestions?? would love to go to your shop and get it done

[@TRUCKINGTIPSDIY]

Hello, you can check the hight of the airbags make sure there not to low, also check the U joint, if its worned out it needs to be replaced, also check yoke if it has a lot of Playland that is not worked out where the seal seats,sorry I don't have a a shop, thank you for watching!

[@youtubeisawesome2487]

check your vent hose for being plugged

[@lancelotmasunda1803]

Its true that check your yoke play ,it might the bearing worn which needs to be replaced.

[@fullthrottlex2]

What’s the part no for the puller

[@israelcadenas1436]

Donde puedo comprar ese tipo de martillo?

[@TRUCKINGTIPSDIY]

Slide hammer,, ebay amazon

[@Tommytv2]

Hey a question. Do you think i can take the pinion nut off with a breaker bar. I font have an impact. Great video i need to do this right now aswell. The dealer wants 1800 to change pinion seal and 2 wheel seals. Im gonna buy all the tools i need and do it myself. I love it. Keep the videos coming.

[@TRUCKINGTIPSDIY]

hello, i dont think a breaker bar will be enough to remove the pinon nut, hopefully you can get the job done, thanks for watching!! let me know once you fix it!!

[@Tommytv2]

@@TRUCKINGTIPSDIY we bent a 40in breaker bar. So i got a 3/4 milwaukee impact. Those things are a beast👍

[@orlanmedina3693]

@@Tommytv2 so did u get it loose with a 1" braker bar? And then used a 3/4 impact?

[@Tommytv2]

@@orlanmedina3693 no the breaker bar bent and was useless. I bought the 3/4 milwaukee impact and about 1 min of holding it down the nut cracked loose. Definately worth the money. 800$ canadian including 2 batteries

[@orlanmedina3693]

@@Tommytv2 holly... I thought with a 1" breaker bar and a big pipe was gonna be able to get it loose

[@hernangarcia5924]

Thank you knowledge

[@joshuastanley5114]

Where did u get the socket? I can't find one

[@TRUCKINGTIPSDIY]

At the dealer

[@greggregorich8048]

i use wheel bearing racer to install seal

[@rogervhooperjr9997]

What is the flat rate for this job?

[@TRUCKINGTIPSDIY]

Im not sure

[@edwinmonterroza7426]

Mine was starting to leak, my mechanic replaced it and after 100 miles it was dripping so bad, he messed up the new one.

[@conleycroom8813]

Great video

[@quocbinhduongnt8646]

made in u.s.a. là số 1 anh ơi

[@TRUCKINGTIPSDIY]

thank you sir!!

[@sams1580]

How much do you charge for this job?

[@TRUCKINGTIPSDIY]

Im not sure how much they charge, we just work on our trucks

[@vladusa7171]

Perfect!

[@TRUCKINGTIPSDIY]

thanks

[@trustinthelord2248]

What year is your truck my guy

[@TRUCKINGTIPSDIY]

2013

[@trustinthelord2248]

@@TRUCKINGTIPSDIY I replace my seals in it still leaking look like the leak coming from around the lock ring what u thk

[@trustinthelord2248]

What year is your truck

[@TRUCKINGTIPSDIY]

2013

[@truthwillsetyoufree1503]

Good video vatos .....at how many miles do you have to do this seals?

[@TRUCKINGTIPSDIY]

gracias, until the seals leak , this truck has around 700K

[@TRUCKINGTIPSDIY]

thanks for watching my videos !!

[@saiff7769]

Nice job man were you using half inch m18 Milwaukee??

[@TRUCKINGTIPSDIY]

thanks you, its the 1" m18, thanks for watching

[@gurihansra3210]

Thanks sir good information plz send me more information tools thanks again

[@TRUCKINGTIPSDIY]

ill try to post more in the description, thank you

[@cbenson1820]

Thank you very much

[@TRUCKINGTIPSDIY]

thanks for watching

[@erwincorado6457]

Hey man thanks for all you videos learning a lot from you so what kind off impact gun do you for that

[@markm0000]

You can do what he did in another video and put a air hookup on the truck for a big impact gun. Let the truck idle for air and you can do anything. Inflate tires, remove big bolts, grind surfaces, etc. etc.

[@abduahmed5477]

You are good mekanek

[@TRUCKINGTIPSDIY]

Thank you sir!!

[@smud4u]

no link on the socket :(

[@denisgodoy711]

Muy sofisticado ya ratos t hubiera sacado ese sello soy mecánico de los rudos

[@TRUCKINGTIPSDIY]

18:50 asi o mas rudo?

[@denisgodoy711]

Cuanto cobras por cambiar la air compresor del cascadia

[@johnb1121]

@@TRUCKINGTIPSDIY question on a freightliner front axle inner axle shaft bushing an seal what tools do you use??? Please Please an where s my tool box tour thanks...

[@utinaisyah5545]

@@TRUCKINGTIPSDIY òĺòl

[@armandoskylar7625]

you all probably dont give a shit but does someone know a trick to log back into an Instagram account..? I was stupid forgot the account password. I would love any tips you can give me.

[@smud4u]

a like the explain thanks , is there a special tool to do these ? like an installer kit ? alguien save si hay un kit de instalasion ? me pueden pasar la liga ?

[@leonidgolomedov1646]

ВСЕ одинаковые водители, русский, нерусский все мажут герметик, смазку ПАЛЬЦЕМ....... ПИТЕР СПАСИБО ................

[@jelenekoutdoors9023]

I have never seen someone reuse the old dust cover and seal mate in my life...

[@terrellscaife2411]

Action pack video

[@ghenaghena2326]

Вроде сальник был нормальный. Сапун надо проверить было.

[@TRUCKINGTIPSDIY]

Thanks for watching sir 🙏

[@ghenaghena2326]

Дякую за відповідь пан🙏

[@jamesray3920]

Floor in a house or building you mean ground 🤔 and if over tighting bolts on reinstall you will twist the 12 point threads this is why many shops replace york due to twisted 12 point head on bolt it's probably best to just replace bolts with new ones

[@waldomiromoreira2077]

You must wear gloves when touching solvents such as gasoline

[@110texan5]

Mr DIY, this was done very incorrect by making sure no fingers were smashed U sir need seriously training. 🤣❤️🇺🇸👍

[@ghenaghena2326]

Funny good.problems supple..

[@nezaralkhayat1487]

El que le esta usando no sabe

[@TRUCKINGTIPSDIY]

Como?

[@chucktaylor4958]

KZbin University.

[@noniponipaa]

sorry cordless impact gun

[@ghostbuilder3187]

shouldve drilled

[@j06c]

What air compressor you using

[@tonymel8235]

great video

[@TRUCKINGTIPSDIY]

Thanks for watching sir 🙏