Try to break this Reverse Chain. RZR 1K Transmission Build.

  Рет қаралды 68,586

SolitudeCustoms

SolitudeCustoms

Күн бұрын

Пікірлер: 70
@TheDean78
@TheDean78 6 ай бұрын
Any problems with it together after the time going. Gears the clearance is really close with the chain and gears ?? Info thanks
@littlechicken963
@littlechicken963 6 жыл бұрын
As a motorcycle tech I have used Yama bond on everything from Harley’s to polaris it’s the best product I have ever found . The sealant Polaris uses is crap .
@mountie816
@mountie816 5 жыл бұрын
Excellent video.Thank you. I only recently learned it had a chain reverse. It was mentioned on the Highlifter review.
@nicksamay1514
@nicksamay1514 5 жыл бұрын
I have a Polaris ranger 1k I’m wanting to delete turf mode and im wanting a upgraded reverse chain and a gear reduction ... can you verify that I can use rzr parts and show me the what I need I to do to make sure I order the right parts ... thanks in advance
@TRPOffroad
@TRPOffroad 7 жыл бұрын
How much did this setup cost? Wanting to do something very similar to mine.
@Solitude313
@Solitude313 7 жыл бұрын
Cody Brooks He brought the parts to me, but I think the Chain was around $5-700 depending which wheeler you have, the GR was like $200, and the HD Plate was around $50
@TRPOffroad
@TRPOffroad 7 жыл бұрын
Gotcha. I appreciate it
@spencerdavis7523
@spencerdavis7523 6 жыл бұрын
General 1k, arched arms, 3 inch brackets and 35s. Chain wouldn't last very long would It?
@snellvilleshoerepair
@snellvilleshoerepair 6 жыл бұрын
How much would you charge to replace a reverse chain? Just a factory chain, no the sprocket and gears
@jonb3977
@jonb3977 Жыл бұрын
can you rebuild my trans with the same upgrades as this, how can I contact you?
@19mckinley96
@19mckinley96 4 жыл бұрын
Do U know of a gear reduction chart? I have a XP 4 10000 (2014) I’d like to get a reduction but I really don’t want to loose any top end!! Suggestions??
@nathanrobinson1174
@nathanrobinson1174 5 жыл бұрын
Is there a gear reduction to commander trans or any bullet proofing that needs to be done ?
@ceciltuley8843
@ceciltuley8843 2 жыл бұрын
Nice video and good idea for reverse chain upgrade. I have a broken chain too- and I need to get my transmission out of the UTV But - first and can't find a video that helps with my model. Do you or any of your viewers know of a video or specific printed manual that will show how to remove a transmission in a 2016 RZR Trail 900 EPS 50" wide UTV? There are lots of videos for other years and models but this 900 has a diagonal frame bar beside the transmission that others don't have that restricts removal, and the Air box is very different than others that I have seen in videos. Anybody have experience with this model?
@darcyward8891
@darcyward8891 3 жыл бұрын
I have a 2016 rzr xp 1000 and looking for the lowest gear possible could you tell me the factory part numbers that I need. Thank you
@jamesansley3983
@jamesansley3983 7 жыл бұрын
Have you found any replacement bearings (timken, sks) for the trans? I've read that the factory bearings are bad about flattening out over time.
@Solitude313
@Solitude313 7 жыл бұрын
james ansley Yes I did. Seems like a great kit that I will be getting next time.
@sebastianmanuele1251
@sebastianmanuele1251 7 жыл бұрын
Thank you so much. I am planning on pulling my transmission some time. Any tips or tricks that you could fill me in on?
@Solitude313
@Solitude313 7 жыл бұрын
Sebastian Manuele I've got 2 other transmission videos like this that you can refer to that should be some help, expecially the 570 Gear Reduction video
@gabrielvillarreal4122
@gabrielvillarreal4122 5 жыл бұрын
Hows it going great work man I always like seeing good tranny upgrade videos . I have a question since your very good with trannys I have a 2014 Polaris ranger crew Diesel , and motor is good but for some reason once the transmission goes into any gear and drives a little bit I cannot get out of that gear unless I turn off the sxs ., then it shifts smooth into any gear but once i get it rolling into any gear Im stuck in that gear until i turn it off . I know this might be out of subject but Im out of ideas I changed the primary and still the same any hints or ideas thanks in advance .
@Solitude313
@Solitude313 5 жыл бұрын
Hey man, thank you I appreciate it. It kind of sounds like your belt is still engaged when at Idle. Theres a roller bearing in the primary that may be hung up. Can you take your clutch cover off and take a look?
@crazyscott71
@crazyscott71 4 жыл бұрын
any problems with that chain setup. im doing the same parts on my xp900
@hpperformance2819
@hpperformance2819 5 жыл бұрын
How did you remove the bearings?
@jdmmiami94
@jdmmiami94 7 жыл бұрын
Where did you buy the bearing retainer plate?? Please and thank you!!
@Solitude313
@Solitude313 7 жыл бұрын
All of these parts came from BioHazard ATV or Specialized UTV
@TrevorFusonAdventures91
@TrevorFusonAdventures91 7 жыл бұрын
how much was it for the kit and,install.
@AllThingsOffroad69
@AllThingsOffroad69 5 жыл бұрын
Is the gear reduction for high or low gear?
@thefloridaman2348
@thefloridaman2348 4 жыл бұрын
all gears
@ICU-th7qj
@ICU-th7qj 5 жыл бұрын
I am thinking about upgrading my reverse chain should I get a gear reduction also? It's a 900s 2016
@Solitude313
@Solitude313 5 жыл бұрын
I would while you are in there. A Gear Reduction is always worth it.
@c.decker8540
@c.decker8540 3 жыл бұрын
Can you put a link for the reduction parts??
@beachboardfan9544
@beachboardfan9544 6 жыл бұрын
So with this beefed up what is the next weakest link, the crank?
@Solitude313
@Solitude313 6 жыл бұрын
No, there is a couple.. output shaft, axles..
@sebastianmanuele1251
@sebastianmanuele1251 7 жыл бұрын
Please make another video putting the transmission back into the bike. I would really appreciate it
@Solitude313
@Solitude313 7 жыл бұрын
Sebastian Manuele This was actually a bench job for me so I didn't pull it but when I do I'll video it.
@MustardSnowman
@MustardSnowman 6 жыл бұрын
Do you put it in neutral before taking case apart???
@Solitude313
@Solitude313 6 жыл бұрын
Guy Schroeder I do yes.
@MustardSnowman
@MustardSnowman 6 жыл бұрын
Thanks guys, anything I should be aware of before taking case apart ? Just want to make sure
@samandrews1395
@samandrews1395 4 жыл бұрын
Ranger 900 xp no higher and no reverse could this be same problem
@chadclm
@chadclm 7 жыл бұрын
bet that was a gilbert hd plate i had the same problem with mine not aligning it mad it a pain but for 40 bucks oh well i guess.... next trans vid can you show how to set the phase on the output shaft
@Solitude313
@Solitude313 7 жыл бұрын
It seems like the idea work but this is a BioHazard ATV Plate. Like it said it went on just took a bit to
@bobcat1
@bobcat1 5 жыл бұрын
The issue I wonder with this upgrade is Yes, he will never break his reverse chain again. But he will need a complete replacement transmission when the shaft bearings wear causing the gears to crash due to the lack of clearance between the gears now.
@FreezLeHD
@FreezLeHD 7 жыл бұрын
Hello solitude; I was wondering if you have any videos how to remove the transmission in the 1000. Mine is leaking right now and wanting to pull it and replace my reverse chain at same time. I appreciate any help you can give buddy! God bless!
@Solitude313
@Solitude313 7 жыл бұрын
Kinda of, not really a walk through but this is the start . kzbin.info/www/bejne/lXm7ZKmPoJ2spMU
@FreezLeHD
@FreezLeHD 7 жыл бұрын
Sweet man thanks! Do you always put tranny in high before you split the case? Any other special tools besides a clutch puller or bearing puller?
@Solitude313
@Solitude313 7 жыл бұрын
The Manual Says to put the cases together in High, but its not really needed untill you go to set the Gear Selector. If you put the cases together in say R its not hard to find H and then set the Selector. Yup thats it, other then a Clutch Puller pretty much.
@FreezLeHD
@FreezLeHD 7 жыл бұрын
Thank you so much for the help man; keep the good videos coming!
@codycollins123
@codycollins123 7 жыл бұрын
how do you like the Porter-Cable power tools
@Solitude313
@Solitude313 7 жыл бұрын
They are alright. I wish it had a 3/8 Drive instead of the chuck tho.
@russellbaeza4489
@russellbaeza4489 7 жыл бұрын
I'm about to pull my transmission to replace the bearings It's a king like something is jumping in there I put it in neutral and it's fine I put it in gear and it start acting like it jumping a gear or something any ideas ?
@michealmolder8752
@michealmolder8752 7 жыл бұрын
If I was going to sell a good one how much would it be worth
@Solitude313
@Solitude313 7 жыл бұрын
Micheal Molder Not sure honestly. Ive just rebuilt.
@blfjr2005
@blfjr2005 6 жыл бұрын
What type of trans fluid do you use?
@Solitude313
@Solitude313 6 жыл бұрын
The Universal Hydraulic Fluid from TSC.
@blfjr2005
@blfjr2005 6 жыл бұрын
SolitudeCustoms thanks for the reply
@Buckbuster88
@Buckbuster88 5 жыл бұрын
Can we get an update on this?
@Solitude313
@Solitude313 5 жыл бұрын
It stretch and started popping. It has been warranted and replaced. Going strong as of now.
@Buckbuster88
@Buckbuster88 5 жыл бұрын
@@Solitude313 I have a general. Nothing wrong with mine right now but I plan on upgrading it. May just go with SATV double chain
@sebastianmanuele1251
@sebastianmanuele1251 7 жыл бұрын
Ok. Thanks for everything
@djnemesis82pluss1877
@djnemesis82pluss1877 7 жыл бұрын
Yeah mine busted out the case but I fixed it with alloy 5
@Solitude313
@Solitude313 7 жыл бұрын
Yea he got lucky with this one
@djnemesis82pluss1877
@djnemesis82pluss1877 7 жыл бұрын
SolitudeCustoms it's an easy fix if you come across the situation I put up a video on it check out super alloy 5
@tjt603
@tjt603 7 жыл бұрын
that is a specialized ATV chain
@Solitude313
@Solitude313 7 жыл бұрын
tjt603 That it is, bought it from Biohazard. Later found out they didn't care to disclose that info. A bunch of people thought they made the chain the way they were talking about it.
@tjt603
@tjt603 7 жыл бұрын
SolitudeCustoms yeah Brent the owner would try something like that.
@Solitude313
@Solitude313 7 жыл бұрын
tjt603 Yea, kinda got that from this. I don't think he sells them anymore after speaking to Specialized at Mud Nats.
@calebwarden9582
@calebwarden9582 7 жыл бұрын
that's specialized atv chain
@itsquick2
@itsquick2 5 жыл бұрын
It’s pure B//S that all these problems exist with these over priced wanta-be hopped up golf carts...
@OleNasty79
@OleNasty79 7 жыл бұрын
Just put that chain in my Ranger
@Solitude313
@Solitude313 7 жыл бұрын
They are pretty dang nice. Shouldnt have any problems
@jordanh4113
@jordanh4113 6 жыл бұрын
How are you re pressing the bearings?
How To Rebuild a Polaris RZR Transmission | Part 1
40:51
Rocky Mountain ATV MC
Рет қаралды 42 М.
STOP This!! You Are Ruining Clutches!!
8:05
Hunterworks Inc.
Рет қаралды 150 М.
Mom had to stand up for the whole family!❤️😍😁
00:39
This dad wins Halloween! 🎃💀
01:00
Justin Flom
Рет қаралды 9 МЛН
Cool Parenting Gadget Against Mosquitos! 🦟👶 #gen
00:21
TheSoul Music Family
Рет қаралды 32 МЛН
Kluster Duo #настольныеигры #boardgames #игры #games #настолки #настольные_игры
00:47
RZR XP 1000 Transmission Disassembly Broken Output Shaft - Part 2
17:42
Stop Buying 15% Gear Reductions for you UTV's
7:45
Hunterworks Inc.
Рет қаралды 43 М.
Polaris RZR Transmission Part 1: How it Works
11:44
SXS Garage
Рет қаралды 26 М.
Polaris Ranger 900 Full Transmission Build Part 1 |3BR OFFROAD
31:17
How To Adjust the Valves on a Polaris RZR 900 & 1000
24:58
Rocky Mountain ATV MC
Рет қаралды 123 М.
BRAND NEW RZR 1000 DESTROYS TRANSMISSION AND REVERSE CHAIN MUDDING
15:54
Arkansas Mud Kings
Рет қаралды 18 М.
Turkey Day Ride In P Town
8:43
42Copperhead
Рет қаралды 3,2 МЛН
Mom had to stand up for the whole family!❤️😍😁
00:39